• 전자공학회논문지SC
• /
• 제39권6호
• /
• pp.42-48
• /
• 2002

다목적 방사선 조사장치의 설계, 제작 및 성능검사에 대해 기술하였다. 세슘-137을 사용한 다목적 방사선조사장치는 생물학에서 저선량 방사선에 대한 영향연구, 혹은 TLD(Thermo Luminescent dosimeter)의 교정을 위해 사용되어진다. 본 조사장치는 방사선 동위원소를 안전한곳에 저장하고 있다가 방사선조사시에만 조사실로 180도 회전하여 설정된 시간만큼 시료에 방사선 조사가 이루어 진 후, 사용이 끝나면 다시 차폐된 저장위치로 복귀하게된다. 제어시스템은 PLC 기반으로 구축하여 저선량율 조사장치의 시제품을 제작하였으며, 또한 컴퓨터를 통해 방사선 조사장치의 제어 및 세부 동작 상태 등을 실시간 검색, 원격제어 및 관리 할 수 있는 종합 관리 프로그램을 개발하였다. 조사실 내부 구성은 시료의 종류에 따라 최대 20RPM까지 다양하게 회전하면서 균일 조사될 수 있도록 조사실 및 챔버를 설계 제작하였으며, 조사실내 넣을 수 있는 조사체 최대 용량은 4.5리터이다. 조사실내의 방사선량의 분포도는 가프크로믹 필름을 사용하여 측정한 결과 2Ci 범위내에서 세슘-137의 경우 공기중에서 0.13cGy/min이었고 일반 물질과 등가인 물에서는 0.11cGy/min로 나타났으며, 오차는 약 ${\pm}$7%의 한도내에서 균일한 분포를 보였다. 또한 실제 누설선량은 조사실 밖 표면에서 최대 0.35mR/hr이였으며 1m 떨어진곳에서는 최대 0.03mR/hr로 허용치 이내였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권9호
• /
• pp.756-761
• /
• 2016

본 연구에서는 소형 단기통 4행정 농용 디젤엔진에 장착될 수 있는 플런저 직경 4 mm, 행정 7 mm의 연료펌프를 설계 및 제작하여 성능특성을 조사하는 것이 목적이다. 실린더 내 연소압력은 자체 제작한 모형 실린더 내에 질소가스를 사용하여 1, 6, 11, 16 및 21 bar의 배압을 형성시켜 모사했다. 실험에 있어서는 연료펌프 회전속도를 600, 800, 1000, 1200 및 1400 rpm로 변화시키면서 개발된 연료펌프의 토출구에서 1 cm 떨어진 지점의 토출압력, 30 cm 떨어진 지점의 송출압력과 송출유량을 배압에 대해 측정하였고, 펌프효율을 계산하였다. 그 결과, 연료펌프 회전속도가 증가하면 펌프의 송출유량은 증가하였고, 실린더 내의 압축압력인 배압이 증가하면 송출유량은 감소하였다. 또한, 연료펌프의 회전속도가 증가할수록 펌프효율이 감소되었고, 실린더 내의 배압이 증가함에 따라 펌프효율은 감소되었다.

• 한국산림과학회지
• /
• 제100권2호
• /
• pp.154-164
• /
• 2011

본 연구는 우리나라 험준한 급경사 지형의 단목중심의 목재생산시스템 등에 적합하고 사방사업, 임도사업 등의 다양한 산림작업에 유용하게 활용할 수 있는 다목적의 반궤도식 산림작업차 개발을 목적으로 실시하였다. 산림작업차량의 기본 차체는 최소회전반경 설계기준과 작업도 폭을 고려하여 차체프레임부의 총길이는 5,750 mm, 차체의 폭은 1,900 mm, 적재부의 적재용량은 약 $2.5m^{3}$으로 설계 제작하였다. 동력원은 3,400 rpm의 최대 96마력 출력의 엔진을 선정하였으며, 유압펌프는 2개의 주펌프와 2개의 보조펌프로 나누어 선정하고, 주펌프는 전후좌우 4개의 주행용 유압모터에 사용하고, 보조펌프는 각종 작업기에 사용하도록 설계 제작하였다. 동력전달방식은 HST(Hydro-Static Transmission) 시스템을 적용하였고, 주행부는 조향가능한 전방 고무바퀴와 무한 궤도형으로 회전하는 후방 크롤러로 설계 제작하고, 조향방식은 애커만 조향방식을 채택하였다. 주행조작부는 일반 자동차의 운전 및 운전석 형태로 설계 제작하였으며, 보조장치로 윈치와 로그그래플 및 아웃트리거를 장착하였다. 시작기의 공차시 임도의 주행속도는 저속 5.3 km/hr, 고속 7.7 km/hr로 나타났다.

• 한국철도학회논문집
• /
• 제16권1호
• /
• pp.7-13
• /
• 2013

철도차량의 실차 규모 동특성시험은 설비 구축, 대차의 제작 및 시험 조건의 설정등과 관련하여 비용, 시간 등의 증대로 많은 어려움이 따른다. 본 연구에서는 실험실 환경에서 차량 진동문제와 안전성을 평가하기 위한 목적으로 축소모델을 제작하고, 개발된 축소모델이 해당 철도차량의 동특성을 정밀하게 모사하는지를 검증하는 평가방법에 대한 연구를 수행하였다. 축소이론은 Jaschinski 상사기법의 이론을 적용하였으며, 1/10 축소모델을 구축하였다. 본 연구에서는 축소 대차의 상하 진동에 초점을 맞혀 시스템을 제작하였다. 시스템은 구동부, 보기, 대차 등 3개의 하부구조로 구성되었으며, 실제 차량으로 환산 시 400km/hr까지 실험가능 하도록 목표로 하였다. 축소 대차의 설계 및 제작과 함께, 동역학해석 프로그램인 ADAMS/View를 이용하여 고유치 해석을 수행하였다. 전산해석으로 도출된 고유진동수는 실험결과와 비교 분석되었다. 시스템이 가지고 있는 초기 5개의 자유도에 상응한 고유진동수를 비교한 결과, 개발된 상사 이론에 따른 축소모형은 충분한 신뢰성을 확보한 것으로 검증되었다. 본 연구에서 개발된 축소모델은 대학실험실에서 차량진동모드를 모사하는 용도로 기획되었으나, 추후 자유도의 추가보완을 통해 고속철도 차량의 대차와 보기구조 동특성 해석에 활용될 수 있을 것으로 판단된다.

• 한국자동차공학회논문집
• /
• 제22권2호
• /
• pp.123-133
• /
• 2014

Minimizing the cylinder wear and the consumption rate of cylinder oil in a large two-stroke diesel engine is of great economic importance. A motor-driven cylinder lubricator for Sulzer RT-flex large two-stroke diesel engines developed by authors is in need of improving the lubricating system to lubricate cylinder parts optimally by an electronically controlled quill device according to changes of engine load and revolution speed. In order to apply the developed accumulating distributor to an integrated cylinder lubricator by the electronically controlled system as the third research stage, the lubricating system is improved in the electronically controlled quill device with a solenoid valve. In this study, the effects of lubricator revolution speed, driving pressure(or plunger stroke) and cylinder back pressure on oil feed rate and lubrication inequality rate are investigated by using the integrated cylinder lubricator system with an accumulated distribution by the electronic control(I.C.S.), and the oil feed rate and lubrication inequality rate of I.C.S. are compared with those of the motor-driven cylinder lubricator by the electronically controlled quill system equipped with an accumulating distributor(E.D.S.). It is found that the oil feed rate of I.C.S. is smaller than that of E.D.S. due to the reduction of delivery velocity by the higher delivery pressure, and the variances of lubrication inequality rate for I.C.S. have become smaller than those of E.D.S. as the driving pressure in all experimental conditions increases, except for the driving pressure of 26 bar(plunger stroke 2 mm) at the cylinder lubricator speed of 120 rpm.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.44-51
• /
• 2019

The paper presents the rotordynamic performance measurements and model predictions of a fuel cell electric vehicle (FCEV) air compressor supported on gas foil bearings (GFBs). The rotor has an impeller on one end and a thrust runner on the other end. The front (impeller side) and rear (thrust side) gas foil journal bearings (GFJBs) are located between the impeller and thrust runner to support the radial loads, and a pair of gas foil thrust bearings are located on both sides of the thrust runner to support the axial loads. The test GFJBs have a partial arc shim foil installed between the top foil and bump strip layers to enhance hydrodynamic pressure generation. During the rotordynamic performance tests, two sets of orthogonally installed eddy-current displacement sensors measure the rotor radial motions at the rotor impeller and thrust ends. A series of speed-up and coast-down tests to 100k rpm demonstrates the dominant synchronous (1X) rotor responses to imbalance masses without noticeable subsynchronous motions, which indicates a rotordynamically stable rotor-GFB system. Finite element analysis of the rotor determines the rotor free-free (bending) natural modes and frequencies well beyond the maximum rotating frequency. The predicted damped natural frequencies and damping ratios of the rotor-GFB system reveal rotordynamic stability over the speeds of interest. The imbalance response predictions show that the predicted critical speeds and rotor amplitudes strongly agree with the test measurements, thus validating the developed rotordynamic model.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.26-31
• /
• 2006

An experimental investigation of an early injection strategy was conducted on a small single cylinder common-rail DI diesel engine to reduce the oxides of nitrogen($NO_x$) emission. The main objectives of this study were to investigate the emissions, performance and combustion characteristics in a diesel engine with early and two-stage injections. The two- stage injection was conducted to reduce the wall-wetting of early injected fuels on the cylinder wall or to promote the ignition of premixed charge. The engine test was performed at conditions of 1500rpm, injection timing ranging from TDC to BTDC $80^{\circ}$. The experimental results show that $NO_x$ emissions were decreased in both cases of early injection and two stage injection compared to the conventional diesel combustion by the near TDC injection. However, soot and products of incomplete products (i.e. HC and CO) are slightly increased. Also, the second injection near TDC promoted the ignition of premixed fuel, therefore, IMEP was increased.

• 대한기계학회논문집B
• /
• 제28권8호
• /
• pp.976-983
• /
• 2004

In high-density hard disk drives, the slider should be made to fly close to the magnetic recording disk to generate better signal resolution and at an increasingly high velocity to achieve better data rate. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation. Contamination particles in the hard disk drive can cause serious problems including slider crash and thermal asperities. We investigated the number and the sizes of particles generated in the hard disk drive, operating at increasing disk rotational speeds, in the CSS mode. CNC (condensation nucleus counter) and PSS (particle size selector) were used for this investigation. In addition, we examined the particle components by using SEM (scanning electron microscopes), AES (auger electron spectroscopy), and TOF-SIMS (time of flight-secondary ions mass spectrometry). The increasing disk rotational speed directly affected the particle generation by slider disk interaction. The number of particles that were generated increased with the disk rotational speed. The particle generation rate increased rapidly at motor speeds above 8000 rpm. This increase may be due to the increased slider disk interaction. Particle sizes ranged from 14 to 200 nm. The particles generated by slider disk interaction came from the lubricant on the disk, coating layer of the disk, and also slider surface.

• Journal of Biosystems Engineering
• /
• 제34권5호
• /
• pp.363-370
• /
• 2009

Hot air heater with light oil combustion is used as the most common heater for greenhouse heating in the winter season. Hot air heaters of 256,246 units have been supplied as main greenhouse heating equipment until 2008 and greenhouse heating cost has reached to 620 billions won in Korea. In order to improve the thermal efficiency of the hot air heater and to reduce the expenses for greenhouse heating, prototype hot air heater was manufactured and tested in this experiment. The heat exchanger of tested prototype hot air heater was circular and hexagonal pipe type and inline and stagger arrangement type. Capacity of the heating was 43,062 kJ/h and total heat transfer area of the heat exchanger was $10.728\;m^2$. According to the performance test, it could supply heat of 38,240 to 35,100 kJ/h depending on the fan motor speed of 1,740~1,220 rpm, respectively. Thermal efficiency of hot air heater was 87.0% to 80.8% in the same conditions. As a result, thermal efficiency of hot air heater with hexagonal pipe-stagger arrangement heat exchanger developed in this study was higher 10.2% than that of conventional hot air heater and heating energy saving rate of 14.3% increased.

• 한국가시화정보학회지
• /
• 제14권3호
• /
• pp.38-45
• /
• 2016

Separation of particles based on different sizes, detection of pathogenic bacteria and isolation of leukocytes from whole blood are typical applications of spiral or helical microchannels. The present study focuses on developing a CD4+ T-cell counting device for monitoring HIV/AIDS patients with the aid of a helical minichannel used for a sample cartridge. For the experiment, $10{\mu}m$ sized microbeads were used for visualization with a fluorescence imaging system. Alignment of microbeads was investigated in a stationary and spinning sample cartridge filled with glycerol-water mixtures of different densities. The helical minichannel was spun using a DC motor controlled by an Arduino board with a Bluetooth shield. It was found that when the sample cartridge was made stationary, no bead alignment was achieved for a medium with density (0% and 20% glycerol) lower than that of the beads, but when it was spun at 2000-3000 rpm for 1-4 min, an alignment was obtained at the top of the channel facilitating optical detection and enumeration of those microbeads. Since an alignment of microbeads was achieved for a medium with density as that of blood plasma, the same approach can be applied for aligning and counting CD4+ T-lymphocytes in whole blood samples collected from patients.