• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.750-755
• /
• 2013

In-wheel motor system gets the driving force from direct-driven motor in the wheel of electric vehicle. It is known as good system for vehicles, from an efficiency, packaging, handling and safety. This paper describes motor and inverter technologies, system configuration and control algorithms for in-wheel type electric vehicle. It is necessary to control on an interrelation perspective because this system drives two motors at same time. In system design, IPMSM(Interior Permanent Magnet Synchronous Motor) including a wide operating range and high-speed rpm is used and flux weakening control is performed in constant power range. Under the torque command from the host controller, auto control box, inverter's output torque is calculated with using torque estimation technique and applied to actual vehicle driving system. It is verified that the configuration and the algorithm are suitable for the in-wheel motor system.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1013-1014
• /
• 2007

This paper presents the design of Brushless DC (BLDC) motor using parametric design. According to the variation of magnitude of back emf and inductance, characteristic equations of BLDC motor are solved then output power, current, and torque ripples are calculated. Therefore output characteristics of BLDC motor according to motor parameter can be easily understood, and the range of back emf and inductance satisfying required output performance can be easily found. Presented design method leads to the BLDC motor design to be simple and effective, and the optimal design of BLDC motor using parametric design for 3kW with 50000rpm is presented.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1090-1094
• /
• 2007

The aim of this study is to estimate the cause of Cooling Tower vibration and eliminate the faults of fan with high vibration in spite of overhaul. The cause of high vibration was that the natural frequency of fan blade coincide with second blade pass frequency. To achieve reduction of Cooling Tower vibration, change motor speed from 1784rpm to 1714rpm, and then the vibration has reduced conspicuously.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.11
• /
• pp.1441-1446
• /
• 2012

An axial-piston-type hydraulic motor involves friction and leakage losses at the sliding parts, contact loss at the mechanism assembly parts, volumetric loss caused by the pressure drop, housing oil churning loss and compressibility from the hydraulic oil pipe resistance, etc. the friction and volumetric loss at the hydrostatic bearing between the piston shoe and the swash plate rotating at high speed and having an oil film gap of 8-15 ${\mu}m$ strongly affects the total efficiency of the hydraulic motor. In this study, a variable swash-plate-type hydraulic piston motor operating under a maximum pressure of 35 MPa, maximum speed of 2,500 rpm, and displacement of 320 cc/rev is tested to verify the optimal ratio of the hydrostatic bearing which is closely related to the hydraulic motor performance.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.9
• /
• pp.789-799
• /
• 2012

In this research, a high temperature superconducting(HTS) motor is designed which is adequate for an electrical aircraft by generating high power density and the potentiality of its application to an aircraft is studied. The designed motor is based on YBCO plates, HTS coils composed of Bi-2223, and ironless air cooled resistive armature. The HTS motor is designed to generate power equivalent to O-360 engine with 180HP at 2700RPM which is used for Cessna and equivalent to CFM56 engine with 18000HP at 5000RPM which is used for B-737. Also, power densities of HTS motors are compared with power densities of aircraft engines so that we can estimate the potentiality of the HTS motor as an aircraft engine.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.11
• /
• pp.221-227
• /
• 2002

Tapping is a machining process that makes a female screw on parts to be assembly together. Recently, as the number of small and compact products increases the radius of tap as small as 1 mm is not unusual and more accurate tapping is needed. In complying with those needs, some high-speed tapping machines with synchronizing function have been developed. This paper describes the development of an ultra high-speed tapping machine up to 10,000rpm. The key factors in the tapping speed are the acceleration/deceleration and the synchronizing errors between spindle motor and fred motor. To minimize the acceleration/deceleration time, a low inertia spindle with a synchronous built-in servo motor was developed. To minimize the synchronizing errors, the tapping cycle algorithm was optimized on an open architecture CNC. The developed tapping machine has the acceleration/deceleration time of 0.13sec/10,000rpm for rigid tapping and the synchronizing error below 4.4%. The cycle time for tapping a female screw of M3 and depth 2 times diameter was 0.55sec.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.2 no.4
• /
• pp.627-634
• /
• 1998

This paper proposes an algorithm which improves capacity of a state observer and low speed driving characteristics of a induction motor by inertia moment identification. In induction motet driving systems, it is difficult to obtain the accurate speed information by a low resolution encoder because the encoder pulses are very few in a low speed range. To improve this problem, state observer based on the Gopinath' theory which estimates speed and disturbance was designed, and disturbance rejection control was realized by application of the observer. Also, inertia moment of the motor was estimated and the nominal inertia of the observer was identified to minimize the error of estimated speed and disturbance. From the simulation and experimental results, it is showed that the proposed observer improved the transient response characteristics in low speed region below 6［rpm］.

• Proceedings of the KIEE Conference
• /
• 1992.07b
• /
• pp.1179-1181
• /
• 1992

A discrete Pl controller is implemented easily using a micro-processor, and it can be confirmed to a adaption of a system and real time processing. In this paper, a speed controller by discrete Pl control using a IBM PC/AT(12MHz) as a micro-processor is implemented and applied to a DC servo motor. In designing the discrite Pl controller, a sampling time and a speed is accepted from key-board, and is processed the control coefficient automatically, and than calculate the gain. Therefore the speed of a DC servo motor is obtained and controlled regulaly. The designed and manufactured discrete Pl control system is experimented. The result shows the good response at the 60 RPM to 250 RPM on the load using the load-spring. The speed error is under 1% on the steady load, but nearly 2-3% on the transient load.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.305-309
• /
• 1999

This paper presents an high efficiency energy conversion system for very high-speed flywheel energy storage system using high Tc superconducting bearings. Main configuration of power convertor is designed to replace of the conventional battery with EMB(Electro Mechanical Battery). PMSM(Permanent Magnet Synchronous Motor) using Halbach array is used as the energy conversion system of motor and generator. Some PWM methods for the high frequency inverter is described and the power factor effects to the torque characteristics and efficiency of the motor and generator is analyzed. As the results, it is verified that the inverter output current is well regulated to be in-phase or inverse-phase sinusoidal waveform to have the wide operational range from 2,500rpm to 42,000rpm. Proposed circuit is designed to obtain the very high speed, high efficiency and stable rotational characteristics, and to be applied to1.2r[kW]/65[Wh] system.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.6 no.6
• /
• pp.879-884
• /
• 2002

There are screw, reciprocating and turbo compressor by structure in an air compressor, essential equipment on he industrial spot. Resently it is wide that the range of turbo compressor's use in gradual, turbo compressor needs high speed rotation of impeller in structure, high rated gearbox and conventional induction motor. This mechanical system increased the moment of inertia and mechanical friction loss. Resently the study of turbo compressor applied super high speed motor and drive, removing gearbox made its size small and mechanical friction loss minimum. In this study we tried to develope variable super high speed motor drive systems for 150Hp, 70,000rpm drect drive Turbo compressor. The result of study is applied to a 150Hp direct turbo compressor and makes it goods.