• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.129.2-129.2
• /
• 2010

AEM which were used for solid alkaline fuel cell(SAFC) were prepared by photo polymerization in method pore-filling with various quaternary ammonium cationic monomers and crosslinkers without an amination process. Their specific thermal and chemical properties were characterized through various analyses and the physico-chemical properties of the prepared electrolyte membranes such as swelling behavior, ion exchange capacity and ionic conductivity were also investigated in correlation with the electrolyte composition. The polymer electrolyte membranes prepared in this study have a very wide hydroxyl ion conductivity range of 0.01 - 0.45S/cm depending on the composition ratio of the electrolyte monomer and crosslinking agent used for polymerization. However, the hydroxyl ion conductivity of the membranes was relatively higher at the whole cases than those of commercial products such as A201 membrane of Tokuyama. These pore-filling membranes have also excellent properties such as smaller dimensional affects when swollen in solvents, higher mechanical strength, lowest electrolyte crossover through the membranes, and easier preparation process compared of traditional cast membranes. The prepared membranes were then applied to solid alkaline fuel cell and it was found comparable fuel cell performance to A201 membrane of Tokuyama.

• Journal of the Korean Chemical Society
• /
• v.12 no.3
• /
• pp.121-127
• /
• 1968

In the oligomerization of p-aminophenol under the catalytic action of the metallic complexes, the effects of the ligands are studied. When the initial velocity of $O_2$ uptake at pH 8 using Fe(Ⅲ) as the central metal and N-hydroxylethylethylenediaminetriacetic acid (HEDTA), ethylenediaminetetraacetic acid (EDTA), diethylenetriaminepentaacetic acid (DTPA), 1,2-cyclohexanediaminetetraacetic acid(CyDTA) as the ligands respectively are compared, the velocities are as the following order: HEDTA > EDTA > DTPA > CyDTA. Further when the effect of the ligands, nitrilotriacetic acid (NTA), HEDTA, EDTA, and DTPA, on the yields of oligomers are compared, the result shows as the following order: NTA > HEDTA > EDTA > DTPA. These are nearly reverse order of the stability constants of the complexes. In order to determine the composition of the mixed complexes at the initial step, the method of continuous variation is used, and it is found that the composition ratio of Fe-EDTA complex to monomer in the mixed complexes is one at pH 5-8 range. It is also found that at pH 9 or in the more alkaline range, side reactions occur to form water soluble dimer of quinone type and the catalytic action of the metallic complex markedly decreases on account of the hydrolysis of the central metal by the $OH^-$ ion.

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.1
• /
• pp.1-14
• /
• 2008

To prepare weather-resistant modified silane acrylic resin coatings for an architectural purpose, tetrapolymers were synthesized by radical polymerization. 3-Methacryloxypropyltrimethoxysilane (MPTS) as a silicone monomer and n-butyl acrylate, methyl methacrylate, and n-butyl methacrylate as acrylic monomers were used. The composition of monomers was adjusted to fix the glass transition temperature of acrylic polymer for $20^{\circ}C$. The composition of MPTS in the synthesized polymer were varied from 10 wt% to 30 wt%. On the basis of synthesized resin amber paints were prepared and their physical properties and effects on weatherability were examined. The presence of MPTS in modified silane acrylic resins generally resulted in low molecular weight and broad molecular weight distribution, and also lowered the viscosity of the copolymers. The coated films prepared from these resins showed good and balanced properties in general. Adhesion to the substrate was outstanding in particular. Weatherability tests were carried out in three different types such as outdoor exposure, QUV, and SWO. The test results showed that the modified silane acrylic resins containing 30 wt% of MPTS had superior weathering properties.

• Korean Journal of Materials Research
• /
• v.30 no.11
• /
• pp.627-635
• /
• 2020

3D printing technology is a processing technology in which 3D structures are formed by fabricating multiple 2D layers of materials based on 3D designed digital data and stacking them layer by layer. Although layers are stacked using inkjet printing to release various materials, it is still rare for research to successfully form a product as an additive manufacture of multi-materials. In this study, dispersion conditions are optimized by adding a dispersant to an acrylic monomer suitable for inkjet printing using Co₃O₄ and Al₂O₃. 3D structures having continuous composition composed of a different ceramic material are manufactured by printing using two UV curable ceramic inks whose optimization is advanced. After the heat treatment, the produced structure is checked for the formation and color of the desired crystals by comparing the crystalline analysis according to the characteristics of each part of the structure with ceramic pigments made by solid phase synthesis method.

• Advances in materials Research
• /
• v.2 no.1
• /
• pp.51-64
• /
• 2013

Enantioselective macromer of trimesic acid was prepared using S(-) menthol with trimesoyl chloride on polyimide (PI) ultrafiltration membrane. The chemical composition of macromer as well as polyimide ultrafiltration membrane was determined by ATR-FTIR Spectroscopy. The optical resolution of chiral alcohols was performed in pressure driven process. The effect of monomer solutions concentration, effect of air-drying time of S(-) menthol solution, effect of reaction time, effect of operating pressure, effect of feed concentration of racemate on the performance of macromer was studied. The synthesised material exhibits separation of chiral alcohols (menthol ~23% and sobrelol ~21%).

• Journal of Pharmaceutical Investigation
• /
• v.19 no.4
• /
• pp.173-178
• /
• 1989

Drug release rates from copolymer hydrogels were controlled by their hydrophilic-hydrophobic balances. As a model copolymer hydrogel, poly(acrylamide-co-styrene) was synthesized at different monomer composition. Release mechanisms of propranolol-HCI from the copolymer matrices were investisated. Swelling rates of the copolymer hydrogels retarded as their hydrophobicity increased. Swelling kinetics of the copolymer hydrogels regulated drug release rates via polymer relaxation controlled release mechanisms. Zero order drug release could thus be achieved within certain periods.

• Korean Journal of Crystallography
• /
• v.12 no.1
• /
• pp.20-24
• /
• 2001

NiZn-ferrite was synthesized usign waste iron oxide catalysts which were produced from styrene monomer process and buried underground as an industrial wastes. The spinel type ferrite was obtained by calcination and sintering of the mixture of finely ground waste catalysts, nickel oxide and zinc oxide powders. The sintered body of Ni/sub 0.5/Zn/sub 0.5/Fe₂O₄ composition at 1230℃ for 5 hours showed the density of 5.38g/㎤, and initial permeability of 59 at 1 kHz. Not only cerium oxide, which existed as a major component in the catalyst, but also unicorporated NiO and ZnO into spinel structure remained as second phases after sintering.

• Fibers and Polymers
• /
• v.1 no.1
• /
• pp.1-5
• /
• 2000

Poly(3-methyltetrahydrofuran)(3-MTHF) and poly(tetrahydrofuran-co-3-MTHF), having very narrow molecular weight distribution were successfully synthesized via photo-induced living cationic polymerization in the presence of diphenyliodonium hexafluorophosphate. Linear relationship between % conversion and number average molecular weight of resulting poly(3-MTHF) in the polymerization of 3-MTHF, carried out at -22$^{\circ}C$, indicates that the 5-membered cyclic oxonium ion, being responsible for the cationic propagation is stabilized by ion pall formation with hexafluorophosphate anion, supplied from the salt. The linear relationship between two parameters, mentioned above was also observed in the copolymerization of 3-MTHF with THF, carried out at 0 and -22$^{\circ}C$. The molecular structures including the copolymer composition and average molecular weight and its distribution is determined by reaction parameters such as monomer feed ratio and reaction temperature.

• Journal of the Korean Applied Science and Technology
• /
• v.17 no.4
• /
• pp.257-261
• /
• 2000

Monodisperse polymer particles have many industrial applications such as surface coatings for metal panels, chromatographic media, spacers for liquid crystal display panel, and fillers for cosmetics, etc.. Micron-size monodispersed poly(methyl methacrylate) particles were prepared by dispersion polymerization in methanol medium in the presence of poly(vinyl pyrrolidone) and 2,2'-azobis(isobutyronitrile) as steric stabilizer and initiator, respectively. Effects of polymerization parameters, such as monomer and initiator concentration, stabilizer type and concentration, solvent composition on average particle size and size distribution were studied.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.150-153
• /
• 2009

Anion exchange polymer electrolyte pore-filling membranes consisting of the whole hydrocarbon materials were prepared by photo polymerization with various quaternary ammonium cationic monomers and characterized on the properties for applying to solid alkali fuel cell (SAFC). Hydrocarbon porous substrates such as polyethylene were used for the preparation of the pore-filling membranes. The hydroxyl ion conductivity of the polymer electrolyte membranes prepared in this research was dependent on the composition ratio of an electrolyte monomer and crosslinking agents used for polymerization. Furthermore, these pore-filling membranes have commonly excellent properties such as smaller dimensional affects when swollen in solvents, higher mechanical strength, lower fuel crossover through the membranes, and easier preparation process than those of traditional cast membranes.