• 한국강구조학회 논문집
• /
• 제22권4호
• /
• pp.377-388
• /
• 2010

HSB600 및 HSB800 고성능강재를 적용한 정모멘트부 강합성거더의 휨거동을 비선형 모멘트-곡률 해석법으로 분석하였다. 연성특성이 다른 3개의 대표적인 강합성거더 기본 단면을 선정하여 모멘트-곡률 해석법으로 모멘트-곡률 이력과 휨저항강도를 구하고 비선형 유한요소해석 프로그램 ABAQUS(2008)로 구한 결과와 비교하여 모멘트-곡률 해석 프로그램을 검증하였다. 비선형 유한요소해석 시에는 플랜지, 복부판 및 콘크리트 바닥판을 판요소로 모델링하여 3차원 강합성거더 유한요소모델을 적용했으며 초기변형과 단면의 잔류응력을 고려하여 해석하였다. 강합성거더 단면에서 콘크리트 바닥판의 28일 압축강도는 30~50MPa를 고려하였으며, 콘크리트 재료는 CEB-FIP(1990) 모델로, 일반 강재와 HSB600 및 HSB800 고성능 강재는 탄소성-변형경화 재료로 모델링하였다. 강합성단면의 연성비, 강거더의 강종, 콘크리트 바닥판의 압축강도, 소성중립축의 위치 등이 강합성거더의 연성특성 및 휨저항강도에 미치는 영향을 분석하였다.

• 한국지진공학회논문집
• /
• 제13권5호
• /
• pp.51-60
• /
• 2009

안전한 내진설계를 위해서는 각 부재에 요구되는 소성변형 요구량을 정확히 예측하여야 한다. 본 연구에서는 등가정적내진설계에 쉽게 활용할 수 있도록, 복잡한 비선형해석 없이 탄성해석을 사용하여 모멘트골조 부재의 소성변형을 평가하는 방법을 개발하였다. 각 부재의 소성변형은 부재 강성과 탄성해석 결과로부터 직접 결정되는 층간변위비 요구량 및 모멘트 재분배 등의 설계 변수로부터 결정된다. 제안된 방법을 8층 2경간의 모멘트골조에 적용하고, 비선형해석을 통하여 제안된 방법의 정확성을 검증하였다. 검증결과, 제안된 방법은 비선형거동에 의한 층간변위비 요구량과 각 부재의 소성변형 요구량을 정확히 평가하였다. 제안된 방법은 부재연성설계와 같은 신축건물의 내진설계에 활용할 수 있을 뿐만 아니라 기존건물의 내진성능평가에도 활용될 수 있을 것으로 기대된다.

• Korean Chemical Engineering Research
• /
• 제54권4호
• /
• pp.487-493
• /
• 2016

양이온교환 고성능액체크로마토그래피에서 라이소자임을 분석하고, 실험결과인 크로마토그램을 통해 모멘트 분석을 수행하였다. 용리 인산완충용액은 1.0, 0.75, 0.5 M의 소금을 포함하였다. 실험변수는 유량, 용리 완충용액중 소금 농도, 시료의 농도로 하였다. General rate (GR) model을 도입하여 1차와 2차 모멘트를 해석하였다. 1차 모멘트 해석에서 평형상수 K를 구할 수 있으며, 이는 $L/u_0$ vs. $({\mu}_1-t_0)/(1-{\varepsilon}_e)(1-{\varepsilon}_i)$]를 도식화했을 때의 기울기이다. 2차 모멘트 해석에서 입자내 확산계수는 이론단수 실험자료에서 계산하였다. 모멘트 분석결과를 통해 여러 물질전달 현상이 이론단 상당높이(HETP)에 주는 영향을 알아보기 위해 van Deemter plot을 작성하고, 총괄 이론단 상당높이($H_{total}$)에 기여하는 $H_{ax}$, $H_f$, 그리고 $H_d$를 조사하였다. 그 중 입자내 확산계수를 나타내는 $H_d$가 가장 지배적이었고, 외부 물질전달 계수를 나타내는 $H_f$의 영향이 가장 미미했다.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제9권6호
• /
• pp.495-499
• /
• 2004

The analyses of peak shapes in chromatography are useful in operating chroma­tographic system. The asymmetry and sharpness of a chromatographic peak are estimated by the reversed-phase adsorption of two standard peptides (angiotensin II bradykinin) on $C_{18}$ In this work, the average particle diameters of $C_{18}$ were 5 and 15 $\mu$m, while the pore sizes were 100 and 300 A. The composition of the mobile phase was $50/50\;vol.\;{\%}$ of a binary mixture of acetonitrile and water with $0.1\%$ TFA, and the particles were packed in a stainless column ($4.6{\times}150$ mm). The third and the fourth central movement were calculated from the chromatographic elution curves by moment analysis. The peak asymmetry was determined by two theoretical calculations: the asymmetry factor by elution peak analysis and skewness with moment analysis. The sharpness was estimated by the fourth central moment. In this work, the most acceptable skewness was calculated when the pore size was 300 A. The large excess was observed on small pore size.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 가을 학술발표회 논문집
• /
• pp.707-712
• /
• 2001

This paper compares the moment-curvature relations of reinforced concrete columns subjected to various loading histories. A sectional analysis was proposed to predict the behavior of reinforced concrete columns. The proposed analysis predicted the real moment-curvature relations of reinforced concrete columns with good agreement. Four types of loading programs were adapted to the analysis. The analysed results indicated that the moment-curvature relations of reinforced concrete columns were strongly affected by the loading history.

• Steel and Composite Structures
• /
• 제18권5호
• /
• pp.1215-1237
• /
• 2015

The majority of connections in moment resisting frames are considered as being fully-rigid. Consequently, the real behavior of the connection, which has some level of flexibility, is ignored. This may result in inaccurate predictions of structural response. This study investigates the influence of flexibility of the extended end-plate connections in the steel moment frames. This is done at two levels. First, the actual micro-behavior of extended end-plate moment connections is explored with respect to joint flexibility. Then, the macro-behavior of frames with end-plate moment connections is investigated using modal, nonlinear static pushover and incremental dynamic analyses. In all models, the P-Delta effects along with material and geometrical nonlinearities were included in the analyses. Results revealed considerable differences between the behavior of the structural frame with connections modeled as fully-rigid versus those when flexibility was incorporated, specifically difference occurred in the natural periods, strength, and maximum inter-story drift angle.

• Structural Engineering and Mechanics
• /
• 제1권1호
• /
• pp.17-30
• /
• 1993

A practical multi-spring model is proposed for a nonlinear analysis of reinforced concrete members, especially columns, taking into account the interaction of axial load and bi-directional bending moment. The parameters of the model are determined on the basis of material properties and section geometry. The axial force-moment interaction curve of reinforced concrete sections predicted by the model was shown to agree well with those obtained by the flexural analysis utilizing realistic stress-strain relations of materials. The reliability of the model was also examined with respect to the test of reinforced concrete columns subjected to varying axial load and bi-directional lateral load reversals. The analytical results agreed well with the experiment.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.556-561
• /
• 2005

The steel shows plastic deformation after the yield point exceeds. The plastic deformation due to overloads occurs at the interior support of a continuous bridge. The plastic deformation is concentrated at the interior support and the permanence deformation at the interior support remains after loads apply. Because local yielding causes the positive moment at the interior support, it is called 'auto-moment'. Auto-moment redistributes the elastic moment. Because of redistribution, auto-moment decreases the negative moment at the interior support of a continuous bridge. In this paper, the plastic rotation is evaluated using the moment-rotation curve proposed by Schalling and Beam-line method. Moreover, auto-moment is derived from the experiment curve.

• Structural Engineering and Mechanics
• /
• 제49권1호
• /
• pp.23-40
• /
• 2014

In this article, using finite element method of analysis (FEM), behavior of the endplate moment connection subjected to axial force and bending moment is investigated. In the FEM model, all the nonlinear characteristics such as material, geometry, as well as contact have been included. First, in order to verify the numerical model of the connection, an analysis of the endplate moment connection conducted without the application of the axial force. Results obtained from FEM indicating a close and good correlation with the experimental results. Then to investigate the influence of the axial forces, the connections subjected to axial forces as well as the bending moment are analyzed. To observe the overall effect of these actions, the momentaxial force interaction diagrams are drawn. It is observed that the presence of axial force even in a small value can change the behavior of the connection significantly. It is also shown that the axial forces can alter the failure mode of the connection; and therefore it could result in a different than the predicted moment capacity of the connection.

• 센서학회지
• /
• 제16권3호
• /
• pp.211-219
• /
• 2007

This paper describes the development of 6-axis force/moment sensor for a humanoid robot. In order to walk on uneven terrain safely, the robot's foot should perceive the applied forces Fx, Fy, Fz and moments Mx, My, Mz to itself, and be controlled by the foot using the forces and moments. Also, in order to grasp unknown object safely, the robot's hand should perceive the weight of the object using the mounted 6-axis force/moment sensor to its wrist, and be controlled by the hand using the forces and moments. Therefore, 6-axis force/moment sensor should be necessary for a humanoid robot's hand and foot. In this paper, 6-axis force/moment sensor for a humanoid robot was developed using many PPBs (parallel plate-beams). The structure of the sensor was newly modeled, and the sensing element of the sensor was designed using theoretical analysis. Then, 6-axis force/moment sensor was fabricated by attaching strain-gages on the sensing elements, and the characteristic test of the developed sensor was carried out. The rated outputs from theoretical analysis agree well with the results from the experiments.