• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.9 no.6
• /
• pp.21-28
• /
• 2010

This study shows an optimization procedure for an automatic determination on the gate position to ensure the fill-uniformity within a part cavity by using the injection molding simulation. For an optimization, the maximum pressure-difference within a part cavity induced at the stage of filling is used to evaluate degree of fill-uniformity. In addition, a direct search scheme based on the reduction of design space is developed and applied in the optimization problem. This corresponding proposed methodology was applied in the optimization on the gate location for a CD-tray molding, as a result, showed the improvement of the fill-uniformity within the cavity.

• Design & Manufacturing
• /
• v.11 no.1
• /
• pp.14-18
• /
• 2017

Recently, the injection-molded products are lighter, and thinner than ever. In this work, Injection molding simulation was conducted to analysis the filling pattern imbalance in high speed injection molding process for thin-wall injection component, 8 inches LGP. Numerical analysis shows that shear heated polymer near the side wall causes filling imbalance between center and side of cavity. Short shot experiments were conducted and compared with simulation results. Filling imbalance ratio showed a tendency to increase for wider fan gate.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.65-69
• /
• 2004

A computer code was developed to simulate the filling stage of the injection/compression molding process by a finite element method. The constitutive equation used here was the compressible Leonov model. The PVT relationship was assumed to follow the Tait equation. The flow-induced birefringence was related to the calculated flow stresses through the linear stress-optical law. Simulations of a disk part under different processing conditions including the variation of compression stroke and compression speed were carried out to understand their effects on flow-induced birefringence. The simulated results were also compared with those by conventional injection molding and with experimental data from literature.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.189-192
• /
• 2002

Recently, micro-nano system is fabricated by photolithograph method. This method can not have mass production, so this method wastes time and human effort. accordingly, the aim of this paper is to research on injection molding of micro-nano system. For injection molding process, development of micro-nano mold is required. Mold for injection mold process is maintained its shape in high pressure and temperature. So in this paper, we studied the simulation of mold fur injection molding and then we consider a result of injection molding simulation.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.45-46
• /
• 2006

In recent years, micro powder injection molding $(\mu-PIM)$ is being explored as an economical fabrication method for microcomponents in microsystems technology (MST). Technical and economic comparison was performed for $\mu-PIM$ processes. Molding experiment and simulation during the filling process were performed to evaluate several different geometries and processing conditions. The influence of material parameters and process conditions on mold filling were examined as a function of features size using microchannels as an example. It was found that the heat conductivity and viscosity of feedstock, geometry and mold temperature were the most critical parameters for complete filling of micro features.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.293-296
• /
• 2008

Injection molding operation consists of filling, packing, and cooling phase. The highest pressure is involved during the packing phase among the operation phases. Cavity pressure depends upon velocity to pressure switchover time and magnitude of packing pressure. The cavity pressure is directly related to stress concentration in the cavity of mold. Thus the observation and control of cavity pressure is very important to prevent mold cracking. In this study, cavity pressures were observed for operational conditions using the commercial CAE software, Moldflow. Operational conditions were velocity to pressure switchover time and packing pressure. Cavity pressures were also measured directly during injection molding. Simulation and experimental results showed good agreement.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.1
• /
• pp.90-96
• /
• 2009

Injection molding process is one of the most important methods to produce plastic parts with high efficiency and low cost. Today, injection molded parts have been increased dramatically the demand for high strength and quality applications. This report investigates that the optimum injection molding condition for minimum of shrinkage. Molding shrinkage is occurred by several reasons such as thermal shrinkage, a hardening process and compressibility. This report concentrate on shrinkage by a hardening process. As Change a holding pressure and holding time, checked deflections of X, Y, Z directions by shrinkage based on same condition. In conclusion, it was found that holding pressure is stronger and holding time is longer, the deflection by shrinkage is smaller because injection molding needs enough time for cooling and high density. The FEM Simulation CAE tool. Moldflow, is used for the analysis of injection molding process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.12 no.5
• /
• pp.94-101
• /
• 2013

Injection molding process is one of the most important methods to produce plastic parts with high efficiency and low cost. The objective of this study is to implement the best plastic injection molding process for LED TV speaker frame. Moldflow analysis and simulation of plastic injection molding process were carried out in order to predict optimal modeling operation conditions and then injection molded part was produced various type of resin temperature, filling time and injection pressure variation. the result was that the best injection molding condition is set as 60bar pressure, 2sec filling time and $310^{\circ}C$ degree. The study result would be useful to variety of plastic injection molding process.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1124-1128
• /
• 2008

Thin-wall injection molding is associated with many advantages, including increased portability, the conserving of materials, and the reduction of the molding cycle times. In the application of the thin-wall molding, a considerable reduction of the effective flow thickness results in filling difficulty. High-frequency induction is an efficient way to overcome this filling difficulty by means of heating the mold surface by electromagnetic induction. The present study applies the induction heating to the injection molding of thinwalled micro structures with high aspect ratio. The feasibility of the proposed heating method is investigated through a numerical analysis. The estimated filling characteristics of the micro-features are investigated with variations of mold temperature and part thickness, of which results are also compared with experimental measurements.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.457-458
• /
• 2012