• Design & Manufacturing
• /
• v.10 no.3
• /
• pp.8-13
• /
• 2016

Despite technological advance, there have been several troubles in photo reaction injection molding (photo RIM) to produce ultra thin light guide panels (LGPs). In this study, micro leakage problem at cavity edge during photo RIM was investigated numerically. In order to obtain optimal processing conditions, we regulated inlet pressure of injected resin at the cavity edge and figured out micro leakage behaviors. At low inlet pressure (less than 100 Pa), though the micro leakage problem was not occurred, another problem, short shot due to not enough driving force, was appeared More than 1,000 Pa of the inlet pressure, injected resin was rapidly leaked through the micro gap at the cavity edge. Finally, we obtained optimal inlet pressure around 600 ~ 1,000 Pa. At this region, injected resin fully filled the cavity without micro leakage behavior. Based on the present study, further comparative investigations with experimental photo RIM should be performed to find optimal processing conditions for produce ultra thin LGPs.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.577-578
• /
• 2006

In this paper, the rubber behavior was calculated for obtaining the optimal process condition which is for producing a transformer with a given performance. This study was carried out using the computer simulation of injection mold filling and packing simulations. In order to remove the crack of product, proper locations of the runner and cooling system configurations could be determined. Based on these results, the transformer is developed by injection molding and guidelines of part design, mold design and processing conditions are established. Finally, the cast savings, cycle time reduce and improvement of productivity will be obtained.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.10a
• /
• pp.423-426
• /
• 2005

The injection molding process has applied to a variety of fields by a development of various plastic resins. Recently, this process has been extending to a field of parts of shoes. In this study, the injection mold of shank which is a one of the parts of shoes has been designed. The position of gate and the injection procedure have been optimized by a simulation using the CAE software and an analysis using the DOE. As a result, the improved injection mold of shank has been manufactured in a short time. Appling the CAE and the DOE at the process of the injection mold design eventually lead an increase in the productivity and the quality of parts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.316-319
• /
• 2002

Injection mold is a manufacturing process used to produce parts of complicated shape at a low cost. Many factors affect the quality of injection molded part during injection molding process. A study on the optimization of injection mold is progressed by using a simulation software like Moldflow. Filling, packing and cooling phases of injection molding processes are analyzed according to the mold design considering the shrinkage of molded part, the degree of filling rate and the wearing of a mold. Taguchi method is applied to analyze the significance of processing parameters and the dynamic characteristics according to the variation of processing parameters. From the results, the mold temperature and packing pressure influenced strongly the shrinkage of injection molded part.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.26 no.5
• /
• pp.209-214
• /
• 2016

Foam reaction injection molding (FRIM) is a widely used process for manufacturing polyurethane foam with complex shapes. Numerical model for polyurethane foam forming reaction during FRIM process has been intensively investigated by a number of researchers to precisely predict final shapes of polyurethane foams. In this study, we have identified a problem related with a previous theoretical model for polyurethane foam forming reaction. Thus, previous theoretical model was modified based on experimental and computational results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.6
• /
• pp.1494-1499
• /
• 2008

Plastic materials are utilized to the most important material of automobile interior-parts due to special characteristics that it is light, good strength and do not transmute quality even if pass long time. This study presented a preliminary analysis of fill time, weld line, air trap etc. for the plastic injection molding process of automobile gearbox cover through simulation using Moldflow.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.474-479
• /
• 2005

Experimental and theoretical studies of internal cavity pressure during injection molding of a spiral tube cavity were carried out. The frozen layer thickness and the evolution of internal cavity pressure were calculated using a commercial software (C-MOLD). The evolution of the internal cavity pressure was recorded during injection molding of polystyrene into a spiral tube mold. To explain the differences observed between the calculated and measured internal cavity pressure, a pressure correction factor (PCF) was introduced based on the plane stress theory. This factor was determined by analyzing the stress state in the melt and calculating the frozen layer thickness near the mold wall. The corrected and experimental pressures have been compared to validate the applicability of the pressure correction factor.

• Korean Journal of Computational Design and Engineering
• /
• v.9 no.4
• /
• pp.351-360
• /
• 2004

An optimal robust design methodology has been developed to minimize the warpage in a decorating panel of monitor molded by the plastic injection. For the associated methodology, the Taguchi's Design Of Experiment (DOE) based on orthogonal arrays and Signal-to-Noise Ratio is combined with commercial simulation tools f3r injection molding. An optimal robust design solution is statistically resulted from the computational simulation. The related experiment was done for evaluations of the warpage in the decorating panel part of monitor. This research showed that the warpage under the applied optimal design conditions was comparatively reduced.

• Design & Manufacturing
• /
• v.6 no.2
• /
• pp.64-69
• /
• 2012

This study looks at plastic mold design for robots and mold manufacture, which is an injection mold branch at The Korea-China-Japan University Grand Prize Contest. Product analysis and layout, molding analysis, and upper and lower core design are carried out to design molds in 2D and 3D. After the design of the cores, NC machining software is used for simulation before actual manufacture. Before the production of end-product, test injection is done to troubleshoot problems like bad dimensions, burr, cracks and stepped pulley.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.6
• /
• pp.1026-1035
• /
• 1987

The injection molding process is used in the fabrication of a large variety of plastic articles. A numerical simulation of the filling stage along the thickness direction is proposed by combining the free surface boundary condition with the relevant governing equations. The mathematical model is based on the equations of continuity, momentum and energy along with inelastic power-law model and relevant boundary conditions. Due to the significant implications for microstructure development in the pro duct, the fountain effect at the advancing free surface is explicitly taken into consideration in the simulation. The model yields data on free surface shape as well as velocity, pressure, temperature and shear stress distributions within the mold cavity. The rearrangement of the velocity and temperature profiles in the vicinity of the melt front is considered in detail.