• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.17 no.5
• /
• pp.84-90
• /
• 2018

When producing a plastic horn cover for an automobile, since the interval between the ribs on the inner surface is narrow, conventional cooling channels cannot be applied and cooling of the mold is difficult. For this reason, the molding operation cannot be completed within a set cycle time. In this study, a conformal cooling channel was applied on the mold to solve the cooling problem. Injection molding simulation was carried out to confirm the effectiveness of the conformal cooling channel. In the analysis results, the mold temperature at the rib section decreased by 33%, and the mold temperature also decreased by 31%. This reduction in temperature allowed for molding within a set cycle time and demonstrated the effectiveness of the conformal cooling channel.

• International Journal of Internet, Broadcasting and Communication
• /
• v.13 no.1
• /
• pp.90-99
• /
• 2021

Recently, studies on wearable devices in ubiquitous computing environments have increased and the technology collecting user's activities to provide services has received great attention. We have compared the step counting methods according to sensor molding methods in case of counting steps by using the piezoelectric sensor. We have classified the cases which could result from the course of molding the internal module of a smart shoe as follows: (i) the module is unmolded, (ii) molded but only to the extent that a sensor is fixed or (iii) molded to the extent that a sensor is not moved. Moreover, we have made comparison to verify which algorithm should be used to increase the accuracy of counting steps by the respective cases. Based on the comparison result, we have confirmed that the accuracy of counting steps is higher when using gradient value rather than when using threshold value. In the case of no molding and small molding under the condition of using gradient value, it was turned out to be 100% accuracy for step counting.

• Design & Manufacturing
• /
• v.17 no.3
• /
• pp.1-7
• /
• 2023

Blow molding is a manufacturing process in which thermoplastic preforms are preheated and then pneumatically expanded within a mold to produce hollow products of various shapes. The two-step process, a type of blow molding method, requires the output of multiple infrared lamps to be adjusted individually, so the process of finding initial conditions hinders productivity. In this study, digital twin technology was applied to solve this problem. A blow molding simulation technique was established and simulation-based metadata was generated. A response surface ROM (Reduced Order Model) was built using the generated metadata. Then, a dynamic ROM was constructed using the results of 3D heat transfer analysis. Through this, users can quickly check the product wall thickness uniformity according to changes in the control value of the heating lamp for products of various shapes, and at the same time, check the temperature distribution of the preform in real time.

• Archives of Metallurgy and Materials
• /
• v.67 no.4
• /
• pp.1511-1515
• /
• 2022

This study investigates the effects of repetitive injection molding on the properties of feedstock using the AISI 4140 feedstock. The properties of feedstock are evaluated from the mixing homogeneity of powder and binder, rheological properties, and dimensional accuracy of parts sintered. The feedstock after the 1^st injection molding shows a better homogeneity than as-received feedstock due to re-mixing effects between the screw and barrel during the injection molding process. As the number of recycling numbers increases, the homogeneity, viscosities ad shrinkage ratio of recycled feedstocks show slight differences with those of the as-received feedstock until the 6^th molding injection. However, some rheological parameters like the moldability index sharply increased up to the 4^th injection but shows a tendency to decrease thereafter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2008.11a
• /
• pp.75-76
• /
• 2008

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2003.04a
• /
• pp.59-61
• /
• 2003

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.22 no.2
• /
• pp.302-310
• /
• 1998

In the accompanying paper, part I, we have presented the physical modeling and the associated numerical analysis of injection molding process with a compressible viscoelastic fluid model. In part II, the effects of compression stage in the injection/compression molding process are presented. Numerical results showed that the injection/compression molding process reduced birefringence as compared with the injection molding process. In this respect, one can conclude that the injection/compression molding process is more suitable for manufacturing the precise optical products than the injection molding process. In the distribution of birefringence, the effect of packing procedure in injection/compression molding process was found to be similar to that in injection molding process. From the numerical results, we found that birefringence becomes smaller as the melt temperature gets higher and the closing velocity of the mold gets smaller with the flow rate and the mold temperature affecting the birefringence insignificantly. As far as the distribution of density is concerned, the flow rate, the melt temperature, and the closing velocity of the mold had insignificant effect on the distribution of density in comparison with the mold temperature.

• Journal of Institute of Convergence Technology
• /
• v.5 no.1
• /
• pp.13-17
• /
• 2015

In wafer level molding progress, the thermal releasing failure phenomenon is shown up as the important problem. This phenomenon can cause the problem including the warpage, crack of the molded wafer. The thermal releasing failure is due to the insufficiency of adhesion strength degradation of the molding tape. To solve this problem, we studied experimental method increasing the release property of the molding tape through the plasma surface treatment on the wafer substrate. In this research, the vacuum plasma treatment system is used for release property improvement of the molding tape and controls the operating condition of the hydrophilic($O_2$, 100kW, 10min) and hydrophobic($C_2F_6$, 200kW, 10min). In order to perform the peeling test for measuring the releasing force precisely, we remodel the micro scale material property evaluation system developed by Korea institute of industrial technology. In case of hydrophilic surface treatment on the wafer substrate, we can figure out the releasing property of molding tape increase. In order to grasp the effect that it reaches to the release property increase when repeating the hydrophilic treatment, we make an experiment with twice treatment and get the result to increase about 12%. We find out the hydrophilic surface treatment method using plasma can improve releasing property of molding tape in the wafer level molding process.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.1
• /
• pp.51-56
• /
• 2009

Recently, with the increasing lightness and miniaturization of high resolution camera phones, the demand for aspheric glass lens has increased because plastic and spherical lens are unable to satisfy the required performance. An aspheric glass lens is fabricated by the high temperature and pressure molding using a tungsten carbide molding core, so precision grinding and coating technology for the molding core surface are required. This study investigates the effect of diamond-like carbon (DLC) and rhenium-iridium (Re-Ir) coating For aspheric molding core surface. The grinding conditions of the tungsten carbide molding core were obtained by design of experiments (DOE) for application in the ultra precision grinding process of the tungsten carbide molding core of the aspheric glass lens used in 5 megapixel, $4{\times}$ zoom camera phone modules. A tungsten carbide molding core was fabricated under this grinding condition and coated with the DLC and Re-Ir coating. By measurements, the effect of DLC and Re-Ir coating on the form accuracy and surface roughness of molding coer was evaluated.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.7
• /
• pp.117-122
• /
• 2010

Recently, aspheric glass lens molding core is fabricated with tungsten carbide(WC). If molding core is fabricated with silicon carbide(SiC), SiC coating process, which must be carried out before the Diamond-Like Carbon(DLC) coating can be eliminated and thus, manufacturing time and cost can be reduced. Diamond Like Carbon(DLC) is being researched in various fields because of its high hardness, high elasticity, high durability, and chemical stability and is used extensively in several industrial fields. Especially, the DLC coating of the molding core surface used in the fabrication of a glass lens is an important technical field, which affects the improvement of the demolding performance between the lens and molding core during the molding process and the molding core lifetime. Because SiC is a material of high hardness and high brittleness, it can crack or chip during grinding. It is, however, widely used in many fields because of its superior mechanical properties. In this paper, the grinding condition for silicon carbide(SiC) was developed under the grinding condition of tungsten carbide. A silicon carbide molding core was fabricated under this grinding condition. The measurement results of the SiC molding core were as follows: PV of 0.155 ${\mu}m$(apheric surface) and 0.094 ${\mu}m$(plane surface), Ra of 5.3 nm(aspheric surface) and 5.5 nm(plane surface).