• 한국주조공학회지
• /
• 제32권1호
• /
• pp.38-43
• /
• 2012

The effects of Mg and Cu amounts on the casting characteristics and tensile property of Al-Zn-Mg-Cu alloys were investigated for the development of high strength aluminium alloys for gravity mold casting. Increase of copper amounts in Al-6%Zn-3%Mgy% Cu alloys resulted in reduction of the fluidity of these alloys and had little effects on the tensile property of these alloys. Increase of magnesium amounts from 1.0wt% to 3.3wt% in Al-6%Zn-x%Mg-0.5%Cu alloys resulted in reduction of the elongation of these alloys from 12% to 3% and increase of the tensile strength of these alloys from 340MPa to 450MPa, but had little effects on the fluidity of these alloys.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.364-367
• /
• 2007

In nano-imprint lithography (NIL) process, which has shown to be a good method to fabricate polymeric patterns, several kinds of pattern defects due to thermal effects during polymer flow and mold release operation have been reported. A typical defect in NIL process with high aspect ratio and low resist thickness pattern is a resist fracture during the mold release operation. It seems due to interfacial adhesion between polymer and mold. However, in the present investigation, FEM simulation of NIL molding process was carried out to predict the defects of the polymer pattern and to optimize the process by FEA. The embossing operation in NIL process was investigated in detail by FEM. From the analytical results, it was found that the lateral flow of polymer resin and the applied pressure in the embossing operation induce the weld line and the drastic lateral strain at the edge of pattern. It was also shown that the low polymer-thickness result in the delamination of polymer from the substrate. It seems that the above phenomena cause the defects of the final polymer pattern. To reduce the defect, it is important to check the initial resin thickness.

• 한국산업융합학회 논문집
• /
• 제25권5호
• /
• pp.889-898
• /
• 2022

In this study, sand casting process was applied to manufacture a large aluminum turbo-type fan used for tank powerpack. To apply the sand casting method, the turbo fan was reverse engineered, and after designing three gating systems, the optimal gating system design was selected by performing casting simulation. In the case of the bottom up-gating system, there is a significant temperature loss of the molten alloy during blade filling. When the molten alloy is completely filled into the sand mold, the blade upper tip and front shroud are below the liquidus temperature. In the case of the top down-gating system, molten alloy scattering occurs, but the temperature loss while the blade is filled is smaller than that of the bottom up type. And after the inflow of molten alloy into the mold is completed, the blade upper tip and front shroud are higher than the liquidus temperature. A sand mold was manufactured with the top down-gating system and the casting process was performed. The fan was made perfectly in appearance without any unfilled parts.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1993년도 가을 학술발표회 논문집
• /
• pp.51-56
• /
• 1993

This is a part a study on the development of High-Performance Concrete ; about experimental results from several test methods to estimate workability in fresh concrete and influences of concrete mix design that affects properties of super-flowing concrete. Super-flowing concrete can be filled in a formwork without any vibration because of its excellent workability of passing narrow space and filling complicated shaped mold, new test methods should be used to estimate the workability and rhelogy in super-flowing concrete instead of slump test method in conventional concrete.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.284-287
• /
• 2002

During resin transfer molding(RTM) process, in case of thick parts, resin flow and void formation should be modeled three dimensionally even though for parts of small thickness, resin flow and void formation can be modeled two dimensionally. In this study, numerical simulations of three dimensional mold filling and void formation during RTM process.

• 소성∙가공
• /
• 제14권2호
• /
• pp.112-120
• /
• 2005

In the die casting process, the flow of liquid metal has significant influence on the quality of casting products and die life. For the optimal process design of gear housing of automobile transmission, various analyses were performed in this study by using computer simulation code, MAGMAsoft. The simulation has been focused on the molten metal behaviors during the mold filling and solidification stages for the sound casting products. Also internal defects were predicted by application of air pressure and feeding criteria.

• Composites Research
• /
• 제12권5호
• /
• pp.23-30
• /
• 1999

Fiber reinforced composite materials are widely used in automotive industry to produce parts that are large, thin, lightweight, strong and stiff. It is very important to know a charge shape in order to have good products in the compression molding. In particular, the product such as a bumper beam is composed of the random and unidirectional fiber mats. The characteristics of flow fronts such as a bulging phenomenon for random mat and unidirectional fiber mat and slip parameters are studied numerically. And the effects of viscosity ratio and stack type on mold filling parameters are also discussed.

• 한국산학기술학회논문지
• /
• 제10권1호
• /
• pp.186-193
• /
• 2009

본 논문에서는 전열(마이크로 히터, 센서)을 이용해 금형의 표면을 가열하는 E-MOLD 특허기술을 적용하여 휴대전화용 복합기능 도광판(Prismless LGP)을 제작하고, 전사성을 평가하였다. 이를 위하여 MEMS 공정을 이용하여 복합기능 도광판용 니켈 스탬퍼를 제작하였고, E-MOLD 기술의 핵심인 이동가열코어(movable heated core)가 설치된 금형을 설계, 제작하였다 이를 이용하여 성형조건 중 금형온도를 변화시키면서 복합기능 도광판을 사출성형으로 제조 하였고, 금형온도가 성형품의 전사성에 미치는 영향에 대하여 알아보았다. 또한, 전산모사 프로그램(CAE)을 이용하여 금형온도와 사출시간에 따른 수지의 유동성을 해석하였다. 금형온도에 따른 도광판의 전사성은 $100^{\circ}C$(25.0nm), $140^{\circ}C$(48.4nm), $180^{\circ}C$(52.1nm)로 나타났고, 스탬퍼(52.1nm)와 비교했을 때 $180^{\circ}C$에서 전사성이 가장 우수했다. 전산모사 해석결과에 따르면, 수지의 유동성은 금형온도($50{\sim}180^{\circ}C$)가 증가할수록 향상되었다. 사출시($1{\sim}2sec$)이 길수록 유동성이 감소하는 경향을 $160^{\circ}C$에서 확인하였다. 따라서 수지의 전사성과 유동성은 금형온도에 따라 증가하고, 특히 유리전이 온도($140^{\circ}C$) 이상에서 크게 상승하였다.

• 대한치과보철학회지
• /
• 제41권4호
• /
• pp.421-439
• /
• 2003

Statement of problem : It is difficult to obtain a good titanium casting body using the traditional sprue design because of high melting point of Ti, and the low fluidity and high reactivity of molten Ti. Purpose : A new sprue design for titanium casting bodies needs more trial and error. In order to decrease the number of trial and error, computer simulation(MAGMASOFT, Magmasoft Giessereitechnologie GmbH, Achen, Germany) was used to optimize sprue design in U-shaped implant superstructures. Material and method : Five kinds of sprue were examined for the design of the sprue former for titanium casting: Sprue design A(sprue length 4 mm, rectangular shape, 4 sprues), Sprue design B(sprue length 4 mm. round shape. radius 2 mm, 7 sprues), Sprue design C (sprue length 2 mm, round shape, radius 2 mm, 7 sprues). Sprue design D (sprue length 2 mm, cone shape, large radius 3mm. small radius 2mm, 7 sprues), and Sprue design E( sprue length 2 mm. one unit channel shape). Sprue design F(sprue length 2mm, one unit channel shape) was also examined for the design of the customized sprue former in the Biotan system(Schutz Dental Gmbh, Germany). The casting bodies were taken in Sprue design A, Sprue design D, Sprue design E, and Sprue design F in the Biotan casting system. The numerically predicted defects were compared with the experimental dental castings by the radiographic and sectional view observations. Results : 1. According to the result of computer simulation, turbulence during mold filling was decreased in the sequence of Sprue design F, Sprue design E, Sprue design D, Sprue design C, Sprue design B, and Sprue design A. 2. The calculated solidification time contours indicate that hot spot was moved from the casting body to the sprue button in the sequence of Sprue design A, Sprue design B, Sprue design C, Sprue design D, and Sprue design E. The filling pattern of Sprue design F was similar to that of Sprue design E. 3 The predicted filling pattern shows that less turbulence was found in the customized sprue former than in the standard sprue former. 4. According to the results of the radiographic and cross sectional observations, casting defects less than 1mm were found at the center of a casting body with Sprue design E and Sprue design F. However, larger casting defects of 4mm were found in a casting with Sprue design A. 5. The predicted casting porosity was similar to that of the real casting. Conclusion : One unit channel-type and customized sprue former can be recommended. Further research and developement of various sprue designs using computer simulation in necessary to optimize casting design, in order to reduce the formation of casting defects in implant titanuim super-structures.

• 한국산학기술학회논문지
• /
• 제21권6호
• /
• pp.482-489
• /
• 2020

본 연구의 목적은 소비자 및 현장의 니즈에 부합하면서 다이캐스팅으로 생산할 수 있는 커플링 부품을 개발하고자 하였으며, 유동 및 응고해석을 기반으로 다이캐스팅 금형 설계, 제작, 및 사출조건 최적화 도출을 실시하였고 사출된 제품의 측정 및 평가를 수행하였다. 유동해석을 통하여 캐비티 내부가 100 % 충진되기 위한 적정한 사출조건은 용탕의 온도 670 ℃, 사출속도 1.164 m/s, 충진압력 6.324~18.77 MPa로 분석되었다. 또한, 응고율이 69.47 %일 때 4개의 캐비티 모두에서 100 %에 근접하는 응고가 발생됨을 알 수 있었으며, 이를 기초로 시사출 조건설정 등에 응용하였으며 그 결과 사이클 타임은 약 6.5초로 도출되었다. 다이캐스팅으로 시사출된 제품의 표면 및 내부의 품질 검사를 수행한 결과 성형불량 및 기공 등의 결함은 전혀 발견되지 않았으며, 주요 개소의 치수를 측정한 결과 모든 항목에서 허용하는 공차 이내의 값을 보였다. 또한, 게이트로부터 약 45 mm 이격된 곳의 평균 경도값은 97.7(Hv)로 나타나는 등 전체적으로 양호한 치수 및 품질의 부품을 제작할 수 있었다.