• 펄프종이기술
• /
• 제48권2호
• /
• pp.28-33
• /
• 2016

This study was conducted to investigate the effects of deep eutectic solvent (DES) treatment on properties of TMP fibers and handsheets. DES was prepared by mixing of lactic acid and betaine (L and B), and the molar ratio of these two components mixtures was controlled to 2:1 (L:B=2:1) and 5:1 (L:B=5:1). As results, lignin was partly extracted from the TMP fibers. Especially, the delignification of TMP samples was promoted according to the increase of the molar ratio of lactic acid. Except for tear index, both tensile index and burst index of handsheets were increased when higher molar ratio of lactic acid was mixed for DES preparation. However, the LB DES treatment of TMP fibers didn't give any effect on the optical properties of TMP handsheets. The plausibility of TMP fiber was to be enhanced by LB DES treatment.

• 한국응용과학기술학회지
• /
• 제26권4호
• /
• pp.394-399
• /
• 2009

The esterification of palmitic acid in Jatropha Oil using 8wt% p-TSA catalyst was done at the 1:8 molar ratio of oil to methanol and $65^{\circ}C$. The conversion of palmitic acid appeared to be 95.3% in 60min. After that, the continuous transesterification of the oil using 0.5wt% KOH, 0.8wt% TMAH mixed catalyst[40vol% KOH(0.5wt%) + 60vol% TMAH(0.8wt%)] and 1.1wt% TMAH was conducted with the flow rates and the molar ratios at $65^{\circ}C$. The overall conversion of Jatropha Oil increased with the decrease of flow rate and showed 95.6% with 9ml/min of flow rate at the 1:8 molar ratio of oil to methanol and $65^{\circ}C$. But it showed 87% with 15ml/min of flow rate at the same conditions. The recovery of methanol(%) appeared to be 86% at the 1:8 molar ratio of oil to methanol, mixed catalyst and $65^{\circ}C$.

• 센서학회지
• /
• 제28권4호
• /
• pp.256-261
• /
• 2019

In this study, mid-infrared transparent zinc sulfide (ZnS) ceramics were fabricated through hydrothermal synthesis with different molar ratios of S/Zn (S/Zn = 0.8, 1.0, 1.2, 1.4, and 1.6). The ZnS ceramics were sintered at a relatively low temperature of $850^{\circ}C$ to prevent the occurrence of the hexagonal phase featuring optical anisotropy. The phase composition, microstructure, and optical properties of the ZnS ceramics were subsequently investigated by employing X-ray diffraction, scanning electron microscopy, and Fouriertransform infrared spectroscopy. The results obtained indicate that the ZnS nanoparticles feature the cubic phase, without the hexagonal phase. Moreover, with increasing S, the crystallinity and particle size of the ZnS nanoparticles increased. The crystallinity and density of the ZnS ceramics improved when the molar ratio of S was higher than the molar ratio of Zn, thereby enhancing the transmittance. Furthermore, the ZnS ceramic with an S/Zn value of 1.2 was found to exhibit the highest transmittance of approximately 69% owing to the reduced occurrence of the hexagonal phase and a high density of 99.8%.

• 한국환경과학회지
• /
• 제21권7호
• /
• pp.769-778
• /
• 2012

Diesel DeNOx experiments using the SNCR process were performed by directly injecting NH3 into a simulated engine cylinder (966 $cm^3$) for which a diesel fuelled combustion-driven flow reactor was designed by simulating diesel engine geometry, temperature profiles, aerodynamics and combustion products. A wide range of air/fuel mixtures (A/F=20~45) were combusted for oxidizing diesel flue gas conditions where an initial NOx levels were 250~900 ppm and molar ratios (${\beta}=NH_3/NOx$) ranged from 0.5~2.0 for NOx reduction tests. Effective NOx reduction occurred over a temperature range of 1100~1350 K at cylinder injections where about 34% NOx reduction was achieved with ${\beta}$=1.5 and cylinder cooling at optimum flow conditions. The effects of simulated engine cylinder and exhaust parts, initial NOx levels, molar ratios and engine speeds on NOx reduction potential are discussed following temperature gradients and diesel engine environments. A staged injection by $NH_3$ and diesel fuel additive is tested for further NOx reduction, and more discussed for practical implication.

• 대한핵의학회지
• /
• 제15권1호
• /
• pp.13-20
• /
• 1981

Using stannous chloride, optimum conditions for $^{99m}Tc$ labelling of some scanning agents such as phytic acid (P A), dimercaptosuccinic acid (DMSA), and calcium diethylenetriaminepentaacetate (Ca-DPTA) were established. Methods of separation and identification of the labelled compounds were practiced by a paper- or thin layer- chromatography. Biodynamic studies of the compounds were also carried out. The results indicate that the molar ratios of the chelating agent and stannous chloride varies only with the concentrations of the chelating agents, and thus the amounts of the stannous chloride per labelling tube were nearly constant $(500\sim600{\mu}g)$ regardless the variation of the molar ratios. It suggests that the given experimental conditions require about $500{\mu}g$ of stannous chloride regardless of the chelating agents. Under alkaline pH, the labelling yields were drastically decreased due to the probable formation of colloidal tin compounds. Biodynamic data showed characteristic patterns with each compound indicating that they are all suitable for the relevant scanning applications.

• Journal of the Korean Wood Science and Technology
• /
• 제27권1호
• /
• pp.72-78
• /
• 1999

요소 멜라민수지의 조성에 의한 속경화의 가능성, 경화촉진제의 첨가에 의한 경화촉진 효과 및 접착성능에 대하여 검토하였다. 수지조성과 동시반응에 의해 제조한 UMF 수지의 겔화성과의 관계는 요소(멜라민/요소 몰비=0.2)에 대한 포롬알데히드의 몰비가 증가할수록 겔화시간이 빨라졌다. 그러나, 요소에 대한 포름알데히드의 몰비가 2.5이상에서는 수지중의 유리포름알데히드량이 KS기준에 합격하지 못하므로 속경화를 위해 수지 합성시 포름알데히드의 첨가량을 높이는 것은 어려울 것으로 생각된다. 또한, 요소에 대한 포름알데히드의 몰비를 3.4로 고정한 UMF수지에 있어서 요소에 대한 멜라민의 몰비가 0.3에서 0.6으로 증가할 수록 수지의 겔화시간은 다소 단축되었으나, 0.6이상에서는 다시 증가하였다. UMF수지의 겔화성과 접착강도는 경화제로서 염화암모늄과 p-툴루맨설폰산, 증량제로서 소액분과 콘글루텐의 병용에 의해 크게 향상되었다.

• Korean Chemical Engineering Research
• /
• 제46권2호
• /
• pp.274-278
• /
• 2008

실란커플링제인 glycidoxypropyl trimethoxysilane(GPTMS)과 methacryloxypropyl trimethoxysilane(MPTMS)을 10:0, 9:1, 7:3, 5:5, 3:7, 0:10의 다양한 몰 비로 혼합한 용액으로부터 sol-gel법을 이용하여 하드 코팅 용액을 제조하였다. 제조된 코팅 용액을 polycarbonate(PC) 시트 위에 스핀 코팅 시키고, $130^{\circ}C$에서 3 h 동안 열 경화시켜 하드 코팅 막을 제조 하였다. 이 과정 중 코팅 용액 중의 GPTMS와 MPTMS의 몰 비 변화가 코팅 막의 물성에 미치는 영향을 살펴보았다. GPTMS와 MPTMS가 5:5의 몰 비로 제조된 코팅 용액으로 PC 시트 위에 코팅한 경우가 다른 조건으로 제조된 코팅 용액보다 우수한 연필경도 및 기재와의 부착력을 보였다. 또한 코팅 용액 중의 $H_2O$의 첨가량이 증가할수록 코팅막의 연필경도는 증가하였다.

• Journal of Microbiology and Biotechnology
• /
• 제15권2호
• /
• pp.254-258
• /
• 2005

We have conducted in vitro reconstitution study of ferritin from its subunits FerH and FerL. For the reconstitution, FerH was produced from an expression vector construct in Escherichia coli and was purified from a heat treated cell extract by using one-step column chromatography. FerL was expressed as inclusion bodies. The denatured form of FerL was obtained by a simple washing step of the inclusion bodies with 3 M urea. The reconstitution experiment was conducted with various molar ratios of urea-denatured FerH and FerL to make the ferritin nanoparticle with a controlled composition of FerH and FerL. SDS-PAGE analysis of the reconstituted ferritins revealed that the reconstitution required the presence of more than 40 molar$\%$ of FerH in the reconstitution mixture. The assembly of the subunits into the ferritin nanoparticle was confmned by the presence of spherical particles with diameter of 10 nm by the atomic force microscopic image. Further analysis of the particles by using a transmission electron microscope revealed that the reconstituted particles exhibited different percentages of population with dense iron core. The reconstituted ferritin nanoparticles made with molar ratios of [FerH]/[FerL]=l00/0 and 60/40 showed that 80 to $90\%$ of the particles were apoferritin, devoid of iron core. On the contrary, all the particles formed with [FerH]/[FerL]=85/ 15 were found to contain the iron core. This suggests that although FerH can uptake iron, a minor portion of FerL, not exceeding $40\%$ at most, is required to deposit iron inside the particle.

• 한국환경과학회지
• /
• 제27권10호
• /
• pp.809-820
• /
• 2018

DeNOx experiments for the effects of hydrocarbon additives on diesel SNCR process were conducted under oxidizing diesel exhaust conditions. A diesel-fueled combustion system was set up to simulate the actual cylinder and head, exhaust pipe and combustion products, where the reducing agent $NH_3$ and $C_2H_6/diesel$ fuel additives were separately or simultaneously injected into the exhaust pipe, used as the SNCR flow reactor. A wide range of air/fuel ratios (A/F=20~40) were maintained, based on engine speeds where an initial NOx level was 530 ppm and the molar ratios (${\beta}=NH_3/NOx$) ranged between 1.0~2.0, together with adjusting the amounts of hydrocarbon additives. Temperature windows were normally formed in the range of 1200~1350K, which were shifted downwards by 50~100K with injecting $C_2H_6/diesel$ fuel additives. About 50~68% NOx reduction was possible with the above molar ratios (${\beta}$) at the optimum flow #1 ($T_{in}=1260K$). Injecting a small amount of $C_2H_6$ or diesel fuel (${\gamma}=hydrocarbon/NOx$) gave the promising results, particularly in the lower exhaust temperatures, by contributing to the sufficient production of active radicals ($OH/O/HO_2/H$) for NOx reduction. Unfortunately, the addition of hydrocarbons increased the concentrations of byproducts such as CO, UHC, $N_2O$ and $NO_2$, and their emission levels are discussed. Among them, Injecting diesel fuel together with the primary reductant seems to be more encouraging for practical reason and could be suggested as an alternative SNCR DeNOx strategy under diesel exhaust systems, following further optimization of chemicals used for lower emission levels of byproducts.

• 대한치과교정학회지
• /
• 제24권3호
• /
• pp.631-648
• /
• 1994

The purpose of this study was to investigate the effects of different types of orthodontic force on the root resorption and repair in rat molar. 77 rats were divided into three groups; The control group was not equiped with orthodontic appliance between incisor and first molar. The experimental group was subdivided into closed coil spring subgroup and elastic chain subgroup by the application methods of orthodontic force. Initial orthodontic force between incisor and first molar was 100g. Experimental period was 8 weeks; for 4 weeks the appliance was acting and for another 4 weeks, removed. Root resorption and repair in the root of first molar was examined by light microscope for histologic changes and by inductively coupled plasma spectroscopy(ICP) for quantitative changes. The results were as follows: 1. In the closed coil spring subgroup odontoclasts and root resolution were appeared one week earlier. 2. One week after orthodontic force was eliminated the repair response in the resorptive lacuna was seen in both subgroups. Delayed resorption was seen on the periphery of resorptive lacunae whereas reparative response was seen in the center of lacunae. A new resorption was seen one week after orthodontic force was eliminated. Root contour was partially restored by repairing of resorbed root. 3. The weight ratios of calcium and phosphorous to the sample were decreased during resorptive process but increased during repair process in both the orthodontic groups, but not more than the control group. 4. By different types of orthodontic force (closed coil spring or elastic chain) resorption process was affected but repair process was not.