• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1993년도 Proceedings of International Conference for Agricultural Machinery and Process Engineering
• /
• pp.443-452
• /
• 1993

Direct freezing tests of soybean seed by liquid nitrogen were carried out at various moisture contents and the following important conclusions were drawn from the results of temperature measurements of soybean seed and photographs of bubbles generated on its surface : 1) Assuming that the temperature gradient in a soybean seed is negligible because of its small seed size and the freezing ratio is followed the Heiss's formula, and a differential equation based on the heat energy balance was introduced . The equation was easily solved by the Runge-Kutta-Gill method and the predicted values of the temperature were in good agreement with the observed data. 2) The photographs of bubble generation during freezing showed the boiling mode was nucleate, and then the most suitable formula on the nucleate boiling heat transfer was introduced from many formulate proposed up to now by fitting the calculated values based on the formula to the observed data. The formula used for the predict on of the seed temperature was as follows: $\frac{{\partial}T_s}{\partial\theta}\;=\;-\frac{{\alpha}(T_s\;-\;T_L)^{3.3}}{W(C_s\;-\;\frac{{\delta}m(CT_s\;+\;{\sigma})}{T_s^2})}$ where C = difference of the specific heat between pure ice and water m=moisture content of soybean seed $T_s$ = seed temperature $T_L$ = Temperature of liquid nitrogen W = mass of soybean seed $\alpha$ = proportional constant $\delta$ = constant depends on variety or the type of seed $\theta$ = time $\sigma$ = latent heat of melting of pure ice This study will give important information in the hydro-freezing technique by liquid nitrogen, available as a new technique of processing agricultural products in the near future.

• 지질공학
• /
• 제21권2호
• /
• pp.157-162
• /
• 2011

지금까지 열전도계수는 불포화토를 대상으로 측정하였으며 측정결과를 토대로 예측 모델의 신뢰성을 연구해 왔다. 그러나 측정 장치의 발열로 인해 불포화토에서는 함수비 구배가 발생하여 열전도계수 측정에 오차가 발생한다. 본 연구에서는 포화된 점성토의 압밀에 따른 열전도계수를 연속적으로 측정하여 건조밀도와 함수비의 변화에 따른 열전도계수의 관계를 연구하였다. 열전도계수는 니들브로브로 측정하였으며 시료의 교란을 최소화하기 위해 니들브로브를 삽입한 상태에서 압밀실험을 진행하였다. 측정결과는 열전도계수 예측 모델을 이용한 결과와 비교를 통해 예측 모델의 신뢰성을 분석하였다.

• 한국환경복원기술학회지
• /
• 제12권6호
• /
• pp.1-17
• /
• 2009

This study was carried out to classify vegetation structure of the Anseong district in the Deogyusan National Park from May 2007 to September 2008 using the gradient analyses and phytosociological method. The vegetation communities were classified into Quercus mongolica, Carpinus laxiflara, Q. serrata, Fraxinus mandshurica, Betula davurica, B. costata, Pinus densiflora and Abies koreana. Characteristics of the vegetation such as species composition, layer structure, vegetation ratio, and the distribution of individual trees by DBH were significantly different among communities. The order of important value of the forest community with DBH 2cm above plants was Q. mongolica (40.02), C. laxiflora (25.65), Q. serrata (24.68), F. mandshurica (21.66), P. densiflora (19.12), Acer pseudosieboldianum (16.96), C. cordata (11.87), B. davurica (11.66), B. costata (10.90), Styrax obassia (10.90) and A. koreana (10.41). Distribution of DBH P. densiflora had a formality distribution, suggesting a continuous domination of these species over the other species for the time being. In contrast, F. mandshurica appeared limited to the valley of the sheet and a higher frequency of young individuals, suggesting a continuous domination of these species the development of a climax forest terrain. This study showed the correlation between each community and the environment according to DCCA ordination. The A. koreana community predominated on the northern slope of the park in the high elevation habitats which had many O-M. F. mandshurica community predominated in the highest elevation habitats which had many Moisture, EX-Cation and T-N. The P. densiflora community mainly occurred on the southern slope of the park in the low elevation habitats which had few Moisture, O-M and T-N. The Q. serrata community and C. laxifiora community appeared on the park in the middle habitats.

• 대한토목학회논문집
• /
• 제34권4호
• /
• pp.1151-1159
• /
• 2014

본 연구에서는 대표적인 전지구 온도지표인 LOC/MTG 온도인자를 이용하여 기후변동성(Climate Variability)을 파악하고 관측수문량의 상대적 변화분석을 위한 특성자료로 활용하였다. 여기서, LOC (Land-Ocean Contrast)는 중위도 지역에서 대륙과 해양의 온도의 차이를 나타내는 지수이며, 고위도 및 아열대 지역의 남북간 기온의 차이는 MTG (Meridional Temperature Gradient)로 정의된다. LOC/MTG 두 패턴의 남북 또는 동서 지점의 변화는 동아시아 지역에서의 대기순환패턴의 변화와 그와 관련된 대기수분이송에 직간접적인 영향인자로서 작용될 수 있다. 또한, 여름철 동아시아의 수문기상의 변화는 식수, 관개용수, 수력발전 및 수산산업과 연관성이 매우 크며, 인간과 자연의 상호관계를 유지하기 위한 지속가능한 수자원의 공급에 중요한 결정요소이다. 따라서 본 연구에서는 한강유역을 대상으로 6월에서 9월 사이에 발생한 여름철 강우 중에서 태풍에 의해 유발된 강우를 제외하고 몬순기후에 의한 한반도 유역의 지역적 강우 특성을 분석하였다. 한강 몬순강우와의 통계적 상관성 분석을 실시한 결과, 여름철 몬순강우의 변화에 민감하게 영향을 미치는 것으로 나타났다.

• 농업과학연구
• /
• 제38권1호
• /
• pp.115-120
• /
• 2011

20% of total energy use to sustain temperature of building inside. In this reasons, researchers effort to improve the thermal insulation capacity with new wall system. Using appropriate materials and consisting new wall system should considered in energy saving design. OSB(Oriented strand board), Larch lining board used to consist wall system. $2{\sim}6$ Larch lining board has tongue & groove shape for preventing moisture. Comparing with gypsum board and green timber lining board as interior sheathing material, temperature difference of Green timber wall system was bigger than temperature difference of gypsum board wall system. This aspects indicate that Green timber wall system was revealed higher thermal insulation property than gypsum board wall system. Gypsum board portion transfer heat easily because temperature difference gradient of gypsum board wall system was smaller than OSB wall system. Total temperature variation shape of G-4-S and G-6-S show similar model but, temperature variation shape in green timber wall portion assume a new aspect. The purpose of this study was that possibility of thermal insulation variation and new composition of wall system identify to improve thermal insulation performance. In the temperature case, this study shows possibility of improving thermal insulation performance. Humidity, sunshine and wind etc. should considered to determine building adiabatic properties.

• Geomechanics and Engineering
• /
• 제19권5호
• /
• pp.435-445
• /
• 2019

A series of element tests with different drainage conditions and strain rates were performed on compacted unsaturated non-plastic silt in unconfined conditions. Soil samples were compacted at water contents from dry to wet of optimum with the degree of saturation varying from 24 to 59.5% while maintaining the degree of compaction at 80%. The tests performed were shear infiltration tests in which specimens had constant net confining pressure, pore air pressure was kept drained and constant, just before the shear process pore water pressure was increased (and kept constant afterwards) to decrease matric suction and to start water infiltration. In constant water content tests, specimens had constant net confining pressure, pore air pressure was kept drained and constant whereas pore water pressure was kept undrained. As a result, the matric suction varied with increase in axial strain throughout the shearing process. In both cases, maximum shear strength was obtained for specimens prepared on dry side of optimum moisture content. Moreover, the gradient of stress path was not affected under different strain rates whereas the intercept of failure was changed due to the drainage conditions implied in this study.

• 설비공학논문집
• /
• 제22권5호
• /
• pp.322-327
• /
• 2010

It is a critical task to keep the ventilation system working in a proper and efficient manner in large multi-storey buildings, and the enthalpy exchanger is becoming an increasingly important part of the ventilation system by playing the function of channeling heat and moisture. We present a computational study on the heat transfer performance of the cross-flow enthalpy exchanger, which is in large use for residential buildings. The ducts are considered whose cross-sectional shapes resemble triangle and longitudinal centerline a cosine wave. It is shown that, as the cross-sectional shape departs from triangle, the heat transfer performance of the duct tends to deteriorate. Also, applying the wave-like shape to the longitudinal centerline of the duct increases the rate of heat transfer and the applied pressure-gradient at the same time. The origin of the performance variations in the cases considered are quantitatively analyzed and discussed.

• Steel and Composite Structures
• /
• 제18권2호
• /
• pp.375-394
• /
• 2015

This paper presents the results of four long-term experiments carried out to investigate the time-dependent behaviour of composite floor slabs with particular attention devoted to the development of non-uniform shrinkage through the slab thickness. This is produced by the presence of the steel deck which prevents moisture egress to occur from the underside of the slab. To observe the influence of different drying conditions on the development of shrinkage, the four 3.3 m long specimens consisted of two composite slabs cast on Stramit Condeck $HP^{(R)}$ steel deck and two reinforced concrete slabs, with the latter ones having both faces exposed for drying. During the long-term tests, the samples were maintained in a simply-supported configuration subjected to their own self-weight, creep and shrinkage for four months. Separate concrete samples were prepared and used to measure the development of shrinkage through the slab thickness over time for different drying conditions. A theoretical model was used to predict the time-dependent behaviour of the composite and reinforced concrete slabs. This approach was able to account for the occurrence of non-uniform shrinkage and comparisons between numerical results and experimental measurements showed good agreement. This work highlights the importance of considering the shrinkage gradient in predicting shrinkage deformations of composite slabs. Further comparisons with experimental results are required to properly validate the adequacy of the proposed approach for its use in routine design.

• Journal of Forest and Environmental Science
• /
• 제39권2호
• /
• pp.65-72
• /
• 2023

The endangered species of Cyathea spinulosa (tree ferns) are among the least concerned ferns of Nepal that bring threats to them and their habitat. A way to reduce such threats is by maintaining a database of species' whereabouts and generating a scientific understanding the habitat preferences. This will eventually help in the formulation of conservation plans for the species. This research aimed to characterize the suitable habitat of C. spinulosa by enumerating the location of species in the Panchase Forests of central Nepal. The statistical index method was applied to relate the occurrence locations of species with various environmental factors for the development of indices. The suitable habitat of C. spinulosa (more and most suitable categories) covered 119 km² and accounted for 43% of the total area studied. 74.4% of occurrence locations of C. spinulosa were recorded from these habitats. The habitat characteristics suitable for C. spinulosa were: proximity to streams (high moisture), land covered by forested area (shady area), mid-elevations of hills about 1,000 m to 2,000 m (sub-tropical climate), slope gradient of 20° to 40° (steep slopes), and northern to eastern aspects. These habitat characteristics could be considered for in-situ protection of tree ferns and designating the conservation plots.

• Journal of the Korean Wood Science and Technology
• /
• 제43권6호
• /
• pp.810-817
• /
• 2015

본 연구는 백합나무 스킨팀버의 ACQ-2, CUAZ-3, CuHDO-1 가압처리 특성을 평가하기 위해 수행되었다. 일차적으로 백합나무 변재부와 심재부 시험편을 대상으로 처리용 목재 함수율이 방부제 처리도에 미치는 영향을 평가하고, 방부제 유효성분인 구리의 처리목재 내 정착 특성을 조사하였다. 본 연구 결과에 의하면 백합나무 변재부는 방부제 종류에 관계없이 조사된 목재함수율 범위(50% 이하)에서 사용환경 범주 H3용 처리목재의 침윤도와 흡수량 기준을 모두 만족하였다. 백합나무 변재부의 방부제 보유량 경사를 조사한 결과, 국립산림과학원 고시 제2011-04호에 제시된 처리용 목재의 함수율(평균 30% 이하)을 만족할 경우 재면으로부터 15 mm 깊이까지에서 사용환경 범주 H3용 처리재의 흡수량 기준을 충족하였다. 백합나무 심재부는 처리도가 매우 불량하여 처리용 목재의 함수율 조건 및 방부제 종류에 관계없이 사용환경 범주 H3용 처리목재의 침윤도와 보유량 기준을 모두 만족시키지 못하였다. 백합나무 변재 및 심재 시험편 공히 비건조 양생보다 건조 양생에서 구리의 정착속도가 빠르고 또한 최종 구리 정착율이 높았으며, 3주간 비건조 양생 후 구리 정착율이 90% 수준에 머물었으며 양생기간을 연장하더라도 정착율은 크게 개선되지 않았다.