• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2004.11a
• /
• pp.249-254
• /
• 2004

The pressing of car body parts is one of the most important sheet metal drawing processes. The corrosion protection oil applied by the steel mills plays a part in every sheet metal forming operation and also makes up the largest proportion of lubricants used. The idea to combine the corrosion protection properties of a corrosion preventive oil with the lubricity of a drawing oil lead to the development of the Anticorit prelubes. Applied at the finishing lines of the steel mills, they finally serve as lubricant in the press shops. A prerequisite for the suitability of a prelube-type oil is the absolute compatibility with all single processes from the coil to the Body in White. The use of prelubes in steel mills reduces the number and quantity of spot lubricants for additional press shop oiling dramatically. But their true benefits can only be fully achieved if the compatibility principle is applied throughout the manufacturing chain. Therefore, modem prelubes systems are modular, even different viscosities can be part of the same concept. This results in a far-reaching multifunctionality of the Anticorit prelube system for all applications.

• Journal of Satellite, Information and Communications
• /
• v.4 no.1
• /
• pp.8-13
• /
• 2009

Software-Based GNSS Simulation Tool is being developed by ETRI as a part of development of software-based GNSS Test & Evaluation Facility which will provide test and evaluation environment for various software level application and navigation algorithm in GNSS. The simulation tool will provide digitized GNSS signal generator and receiver including GPS and Galileo. The detailed design and module implementation for the Software GNSS signal generation and signal processing simulation tool and its modular implementation is presented in this paper.

• Proceedings of the Korea Society for Simulation Conference
• /
• 2002.05a
• /
• pp.253-258
• /
• 2002

This paper proposes a methodology for development of protocol models. The methodology attempts to employ two modeling environments in models development, NS2 and DEVSim++, which will interoperate during simulation. NS2 is a widely used network simulator in protocol research, which employs an informal modeling approach. Within the approach time and state information of protocol models are not explicitly described, thus being hard to validate model. On the other hand the DEVS formalism is a mathematical framework for modeling a discrete event system in a hierarchical, modular manner. In DEVS, model's time and state information is described explicitly, By using DEVS formalism, models can easily be validated and errors in the modeling stage can be reduced. However, the DEVS simulator, DEVSim++, supports a small amount of models library which are required to build simulation models of general communication network. Although NS2 employs an informal modeling approach and models validation is difficult, it supports abundant models library validated by experimental users. Thus, combination of DEVS models and NS2 models may be an effective solution for network modeling. Such combination requires interoperation between DEVSim++ simulator and NS2 simulator. This paper develops an environment for such interoperation. Correctness and effectiveness of the implemented interoperation environment have been validated by simulation of UDP and TCP models.

• ETRI Journal
• /
• v.34 no.5
• /
• pp.743-752
• /
• 2012

Semantic interpretation of the relationship between noun compound (NC) elements has been a challenging issue due to the lack of contextual information, the unbounded number of combinations, and the absence of a universally accepted system for the categorization. The current models require a huge corpus of data to extract contextual information, which limits their usage in many situations. In this paper, a new semantic relations interpreter for NCs based on novel lightweight binary features is proposed. Some of the binary features used are novel. In addition, the interpreter uses a new feature selection method. By developing these new features and techniques, the proposed method removes the need for any huge corpuses. Implementing this method using a modular and plugin-based framework, and by training it using the largest and the most current fine-grained data set, shows that the accuracy is better than that of previously reported upon methods that utilize large corpuses. This improvement in accuracy and the provision of superior efficiency is achieved not only by improving the old features with such techniques as semantic scattering and sense collocation, but also by using various novel features and classifier max entropy. That the accuracy of the max entropy classifier is higher compared to that of other classifiers, such as a support vector machine, a Na$\ddot{i}$ve Bayes, and a decision tree, is also shown.

• Journal of the Korean housing association
• /
• v.26 no.5
• /
• pp.97-104
• /
• 2015

This paper aims to discuss the concept of resilience in floating housing, to investigate the resilient features of floating houses & to review the possibility of floating housing as a new form of resilient living, and to suggest some reference ideas for the planning and design of floating housing projects. Resilient features of the floating house can be summarized as the buoyant characteristics for natural disasters, the easy employment & potential use of renewable and nearly self-sufficient energy systems in locations subject to limited energy sources, the movability, mobility, long life, water recycle system, prefabrication and modular construction with the potential for reduced environmental impact. Additional benefits include the potential for a peaceful and comfortable atmosphere due to direct connections with nature, good relationship with neighbors, a solid social spirit of unity, and sense of security. Considering the resilient features of floating house at a time of serious climate change requires a new paradigm, and floating/amphibious/floatable housing has great possibility as a new form of resilient living.

• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.151-156
• /
• 2001

Experimental frictional and wear characteristics of silicon graphite materials is studied in this paper. Those specimens are lubricated with high temperature and highly pressurized water to simulate the same operating condition for the journal bearing and the thrust bearing on the main coolant pump bearing in the newly developing nuclear reactor named SMART(System-integrated Modular Advanced ReacTor). Operating condition of the bearings is realized by the tribometer and the autoclave. Friction coefficient and wear loss are analyzed to choose the best silicon graphite material. Pin on plate test specimens are used and coned disk springs are used to control the applied force on the specimens. Wear loss ana wear width are measured by a precision balance and a micrometer. The friction force is measured by the strain gauge which can be used under high temperature and high pressure. Three kinds of silicon graphite materials are examined and compared with each other, and each material shows similar but different results on frictional and wear characteristics.

• Journal of Power Electronics
• /
• v.16 no.2
• /
• pp.553-563
• /
• 2016

This paper presents a digital hardware implementation of a real-time simulator for a multiphase drive using a field-programmable gate array (FPGA) device. The simulator was developed with a modular and hierarchical design using very high-speed integrated circuit hardware description language (VHDL). Hence, this simulator is flexible and portable. A state-space representation model suitable for FPGA implementations was proposed for a dual three-phase induction machine (DTPIM). The simulator also models a two-level 12-pulse insulated-gate bipolar transistor (IGBT)-based voltage-source converter (VSC), a pulse-width modulation scheme, and a measurement system. Real-time simulation outputs (stator currents and rotor speed) were validated under steady-state and transient conditions using as reference an experimental test bench based on a DTPIM with 15 kW-rated power. The accuracy of the proposed digital hardware implementation was evaluated according to the simulation and experimental results. Finally, statistical performance parameters were provided to analyze the efficiency of the proposed DTPIM hardware implementation method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.1
• /
• pp.159-166
• /
• 2006

Chassis system has a large influence on ride quality, stability and NVH performance of a car. To improve the performance and reduce cost, the development of chassis modular assemblies is emphasized. To develop chassis corner modules, it is necessary to predict the performance of full vehicle motion such as ride, handling performance, NVH characteristics and durability of modules. In this paper, full vehicle test is performed to acquire the road load data of chassis corner module of passenger car. 3-axis simulator modeling are carried out to simulate reaction force analysis and fatigue analysis of new developed modules. Also, real simulator tests to validate performance of new developed modules are performed. We had developed the accelerated durability test procedure of KATECH PG and it is used to test chassis corner modules at laboratory and simulate durability performance. All these results have been provided to module and parts company and make an important role to develop chassis corner modules.

• Nuclear Engineering and Technology
• /
• v.48 no.4
• /
• pp.893-905
• /
• 2016

Numerous advanced reactor concepts have been proposed to replace light water reactors ever since their establishment as the dominant technology for nuclear energy production. While most designs seek to improve cost competitiveness and safety, the implausibility of doing so with affordable materials or existing nuclear fuel infrastructure reduces the possibility of near-term deployment, especially in developing countries. The organic nuclear concept, first explored in the 1950s, offers an attractive alternative to advanced reactor designs being considered. The advent of high temperature fluids, along with advances in hydrocracking and reforming technologies driven by the oil and gas industries, make the organic concept even more viable today. We present a simple, cost-effective, and safe small modular nuclear reactor for offshore underwater deployment. The core is moderated by graphite, zirconium hydride, and organic fluid while cooled by the organic fluid. The organic coolant enables operation near atmospheric pressure and use of plain carbon steel for the reactor tank and primary coolant piping system. The core is designed to mitigate the coolant degradation seen in early organic reactors. Overall, the design provides a power density of 40 kW/L, while reducing the reactor hull size by 40% compared with a pressurized water reactor while significantly reducing capital plant costs.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.10
• /
• pp.483-493
• /
• 2001

The 3-phase induction is used for the MCP(main coolant pump) and the pure water is used for lubrication of bearing because of the difficulty of repair. Therefore the type of motor is the canned-motor that is welded by sealed can to prevent the stator and rotor from the lubricating water. A lot of Eddy currents are produced in the can because of the conductivity of material. And these eddy currents in the can are the most important cause that decrease the efficiency of induction motor. Therefore we have to find the method to decrease these eddy currents in the can for the improvement of efficiency of motor. In this paper, we proposed the method of design and analysis of canned-motor using equivalent circuit with consideration of can loss for the improvement of efficiency of motor.