• Journal of the Korean Society of Safety
• /
• v.28 no.5
• /
• pp.21-26
• /
• 2013

Delamination of cover concrete due to re-bar corrosion is a critical damage reducing structural safety of reinforced concrete structures. Therefore, it should be detected and evaluated to provide appropriate maintenance to recover structural integrity. Impact-echo method, which utilizes thickness vibration characteristics of delaminated concrete section, is effective for detection and evaluation of small areal size delamination. However, it may not be applicable for large areal size delamination in which flexural vibration modes are dominated. In this study, applicability of vibration mode shapes of delaminated concrete section is investigated for visualization of delamination region in concrete structures. Numerical and experimental modal tests are performed to estimate mode shapes of delaminated concrete section and linear absolute summation technique is proposed for effective visualization of delamination region based on estimated mode shapes.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.10
• /
• pp.1092-1098
• /
• 2009

The squeal propensity of an automotive disc brake system is studied in the theoretical and computational manner. The rotating disc is in contact with two stationary pads and the nonlinear friction is engaged on the contact surface. The friction-coupled equations of motion are derived in the finite element(FE) of the actual brake disc and pad. From the general definition of friction force, the rotation and in-plane mode effects can be included properly in the brake squeal model. The eigenvalue sensitivity analysis and the mode shape visualization at squeal frequencies are also conducted for the detailed investigation. It is found that the squeal propensity is strongly influenced by rotation effect and the in-plane mode can be involved in squeal generation.

• Steel and Composite Structures
• /
• v.2 no.3
• /
• pp.223-236
• /
• 2002

An analytical procedure based on the transfer matrix method to estimate not only the natural frequencies but also vibration mode shapes of the thin-walled members composed of interconnected cylindrical shell panels is presented. The transfer matrix is derived from the differential equations for the cylindrical shell panels. The point matrix relating the state vectors between consecutive shell panels are used to allow the transfer procedures over the cross section of the members. As a result, the interactions between the shell panels of the cross sections of the members can be considered. Although the transfer matrix method is naturally a solution procedure for the one-dimensional problems, this method is well applied to thin-walled members by introducing the trigonometric series into the governing equations of the problem. The natural frequencies and vibration mode shapes of the thin-walled members composed of number of interconnected cylindrical shell panels are observed in this analysis. In addition, the effects of the number of shell panels on the natural frequencies and vibration mode shapes are also examined.

• Journal of KSNVE
• /
• v.8 no.5
• /
• pp.936-948
• /
• 1998

A theoretical formulation for the analysis of free vibration of a cylindrical shell with a circular plate attached at an arbitrary axial position of the shell under various kinds of boundary conditions was derived and programed to get the numerical results for natural frequencies and mode shapes of the combined system. The boundary conditions of the shell to be considered here are clamped-free, clamped-simply supported, both ends clamped and both ends simply supported. The frequencies and mode shapes from theoretical calculation were compared with those of commercial finite element code, ANSYS. The results showed good agreement with those of ANSYS in frequencies and mode shapes. The program will contribute to the design optimization of a shell/plate combined system through the analysis of natural frequencies and mode shapes for the system.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.557-563
• /
• 2010

Mode II interlaminar fracture toughness was measured and fractured surfaces were observed of carbon/epoxy and glass/epoxy woven fabric composites for carbody structure. Woven fabric carbon/epoxy and glass/epoxy composites that made with prepreg and epoxy resin(RS1222) are used in carbody structure of Korean tilting train(TTX) and low floor bus. ENF(End Notched Flexure) specimens having $120mm{\times}20m{\times}5mm$ shape and 35mm initial crack were made with each composites and three point bending tests according to ASTM D790 were conducted for these specimens. Crack lengths in tests were recorded using optical microscope and digital camcorder. NL(Non Linear), 5% offset and Max. load points in load -displacement curves were checked and mode II interlaminar fracture toughness of these points were calculated and compared. Fractured surfaces of specimens were observed using optical microscope and mode II delamination behavior of each composites was discussed.

• Korean Journal of Optics and Photonics
• /
• v.4 no.3
• /
• pp.330-337
• /
• 1993

Figure '8' type, passively-mode-locked erbium-doped-fiber ring laser was developed, incorporating a nonlinear loop mirror. Transmittance of the loop mirror was found to be dependent on the incident light intensity due to the non-reciprocal nonlinear phase shift, which enables the passive mode locking of the laser. Self-starting of stable mode locking was possible with only controlling the polarization controllers inside the cavity without any help of external perturbation or modulation. The mode-locked output pulse shape was discussed in relation with the transmission characteristics of nonlinear loop mirror.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.775-779
• /
• 2003

Recently, a new type actuator using multi-pole magnet has been developed for high-density and high-speed disk drive, which can be achieved higher sensitivity than a conventional actuator for applying one-pole magnet. However, it is very difficult for the actuator of multi-pole magnet to meet simultaneously the optimal design condition for reducing rolling mode effect and improving driving sensitivity because the force center is different from the mass center In this paper, First We propose the new shape coil for tracking which can reverse moment additionally in tracking motion, Next we achieve the optimal design to reduce phase disturbance and peak gain at the rolling mode frequency. Finally, the validity of the proposed methods is proved from experimental results.

• Smart Structures and Systems
• /
• v.13 no.5
• /
• pp.797-819
• /
• 2014

This paper presents a theoretical algorithm for constructing the mode shapes of a bridge from the dynamic responses of a test vehicle moving over the bridge. In comparison with those approaches that utilize a limited number of sensors deployed on the bridge, the present approach can offer much more spatial information, as well as higher resolution in mode shapes, since the test vehicle can receive the vibration characteristics of each point during its passage on the bridge. Basically only one or few sensors are required to be installed on the test vehicle. Factors that affect the accuracy of the present approach for constructing the bridge mode shapes are studied, including the vehicle speed, random traffic, and road surface roughness. Through numerical simulations, the present approach is verified to be feasible under the condition of constant and low vehicle speeds.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.302-307
• /
• 2004

This paper reviewed characteristics of fatigue crack behavior observed by changing various shapes of initial crack and magnitudes of loading in compact tension shear(CTS) specimen subjected to shear loading. In the high-loading condition, fatigue crack under shear loading propagated branching from the pre-crack tip. Meanwhile, the secondary fatigue crack in the low-loading condition which was created in the notch root due to friction on the pre-crack face grew to a main crack. Influenced by the mode II loading condition, fatigue crack propagation retardation appeared in the initial propagation region due to the reduction of crack driving force and friction on crack face. In both cases, however, fatigue cracks grew in tensile mode type. Propagation path of fatigue crack under the shear loading was 70 degree angle from the initial crack regardless of its shape and load magnitude.

• Structural Engineering and Mechanics
• /
• v.54 no.4
• /
• pp.711-723
• /
• 2015

This study investigates the identification of added mass and its location in the glass fiber reinforced polymer (GFRP) beam structures. The main emphasis of this paper is to ascertain the importance of inclusion of rotational degrees of freedom (dofs) in the introduction of added mass or damage identification. Two identification indices that include the rotational dofs have been introduced in this paper: the modal force index (MFI) and the modal rotational curvature index (MRCI). The MFI amplifies damage signature using undamaged numerical stiffness matrix which is related to changes in the altered mode shapes from the original mode shapes. The MRCI is obtained by using a higher derivative of rotational mode shapes. Experimental and numerical results are compared with the existing methods leading to a conclusion that the contributions of the rotational modes play a key role in the identification of added mass. The authors believe that the similar results are likely in the case of damage identification also.