• The Journal of the Convergence on Culture Technology
• /
• v.5 no.2
• /
• pp.381-388
• /
• 2019

In this paper, we propose a new wireless transport network, which is named as Mobile Xhaul Network(MXN), that is enable to bring cost efficiency of fronthaul, midhaul and backhaul and to make easy installation of 5G Radio Access Network(RAN). For this purpose, we design XDU discovery and xhaul link setup mechanism with MXN architecture and operational procedure. Especially, in this paper, we propose various types of beam discovery mechanisms for mmWave based radio access on XDU and evaluate proposed schemes. The Simulation result shows that threshold based scheme and information based scheme have less than about 50% beam discovery latency compared to full search scheme.

• International Journal of Concrete Structures and Materials
• /
• v.9 no.3
• /
• pp.307-321
• /
• 2015

The primary objective of this study is to investigate the feasibility of an innovative surface-mount sensor, made of a piezoelectric disc (PZT sensor), as a consistent source for surface wave velocity and transmission measurements in concrete structures. To this end, one concrete slab with lateral dimensions of 1500 by 1500 mm and a thickness of 200 mm was prepared in the laboratory. The concrete slab had a notch-type, surface-breaking crack at its center, with depths increasing from 0 to 100 mm at stepwise intervals of 10 mm. A PZT sensor was attached to the concrete surface and used to generate incident surface waves for surface wave measurements. Two accelerometers were used to measure the surface waves. Signals generated by the PZT sensors show a broad bandwidth with a center frequency around 40 kHz, and very good signal consistency in the frequency range from 0 to 100 kHz. Furthermore, repeatability of the surface wave velocity and transmission measurements is significantly improved compared to that obtained using manual impact sources. In addition, the PZT sensors are demonstrated to be effective for monitoring an actual surface-breaking crack in a concrete beam specimen subjected to various external loadings (compressive and flexural loading with stepwise increases). The findings in this study demonstrate that the surface mount sensor has great potential as a consistent source for surface wave velocity and transmission measurements for automated health monitoring of concrete structures.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.189-192
• /
• 2002

In this study, The experimental open-tube-type and close-tube-type thermoacoustic refrigerator were constructed. The resonant characteristics of a thermoacoustic refrigerator were investigated. In order to determine the optimum resonant tube length and frequency, We changed the length of resonant tube from 400mm to 850mm and the frequency from 100Hz to 1000Hz. In case of first harmonic, the temperature difference of open-tube-type (1/4 wave) refrigerator was $41^{\circ}C$(resonator length :500mm). The temperature difference of close-tube-type (1/2 wave) refrigerator was $43^{\circ}C$(resonator length :850mm). In this experiments, the experimental 1/2 wave refrigerator is slightly cooler than the experimental l/4 wave refrigerator.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.3
• /
• pp.253-258
• /
• 2013

In this paper, a free-space material measurement technique is discussed in W-band(75~110 GHz). For the accurate measurement of S-parameters of an MUT(Material Under Test) in free space, a W-band quasi-optical free-space material measurement system, less affected by the measurement environments, is discussed, and GRL(Gated Reflect Line) method for calibrating the measurement system is described. Proposed technique is verified for 'Air' and measurement results for arystal plates of thickness 1.1 mm, 2 mm, 2.75 mm and 5 mm are also shown.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.423-429
• /
• 2006

This paper deals with research for development of electromagnetic wave absorbers in sheet type for mobile phones. By controlling the sendust ratio, the $Al(OH)_3$ coating, the thickness, the kind of binders, and the milling time, electromagnetic wave absorbers were prepared and examined. Central frequency shills toward lower 2.2 GHz, 1.29 GHz, 842 MHz with increasing thickness 1 mm, 2 mm, 3 mm of the absorber, and absorption ability controlled each 2.2 GHz to 1.91 GHz, 1.29 GHz to 801 MHz, 842 MH2 to 801 MHz adjust sendust amount from 80 wt% to 85 wt%. The absorption band of the electromagnetic wave absorber coated with $Al(OH)_3$ becomes larger than that of non-coated one. Sendust composite microwave absorbers mixed with CPE were prepared at $70^{\circ}C$ in temperature. The fabricated electromagnetic wave absorbers show a reflection coefficient 5.76 dB at 1.8 GHz in thickness of 0.85 mm.

• ETRI Journal
• /
• v.35 no.1
• /
• pp.120-130
• /
• 2013

This paper presents an analysis of resource assignment for multihop communications in millimeter-wave (mm-wave) wireless personal area networks. The purpose of this paper is to figure out the effect of using directional antennas and relaying devices (DEVs) in communications. The analysis is performed based on a grouping algorithm, categorization of the flows, and the relaying DEV selection policy. Three schemes are compared: direct and relaying concurrent transmission (DRCT), direct concurrent transmission (DCT), and direct nonconcurrent transmission (DNCT). Numerical results show that DRCT is better than DCT and DCT is better than DNCT for any antenna beamwidths under the proposed algorithm and policy. The results also show that using relaying DEVs increases the throughput up to 30% and that there is an optimal beamwidth that maximizes spatial reuse and depends on parameters such as the number of flows in the networks. This analysis can provide guidelines for improving the performance of mm-wave band communications with relaying DEVs.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.8 no.3
• /
• pp.262-273
• /
• 2003

We have analyzed the characteristics of the monthly mean sea surface winds and wind waves near the Korean marginal seas in the 2002 year on the basis of prediction results of the sea surface winds from MM5/KMA model, which is being used for the operation system at the Korea Meteorological Administration and the third generation wave model, WAVEWATCH-III. which takes the sea surface winds derived from MM5/KMA model as the initial data. Statistical comparisons have been applied with both the marine meteorological observation buoy and the TOPEX/POSEIDON satellite wave heights data to verify the model results. The correlation coefficients between the models and observation data reach up to about 60-80％, supporting that these models satisfactorily simulate the sea surface winds and wave heights even at the coastal regions except for Chilbal-Do located very close to the land. Based on these verification results, the distributions of monthly mean sea surface winds, significant wave heights, wave lengths and wave periods around the Korean marginal seas during 2002 year have been represented.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.5
• /
• pp.1040-1046
• /
• 2015

With the rapid progress of electronics and radio communication technology, human enjoys greater freedom in information communication. However, EMW (Electro-Magnetic Wave) environments have become more complicate and difficult to control. Thus, international organizations, such as the American National Standard Institution (ANSI), Federal Communications Commission (FCC), the Comite Internationale Special des Perturbations Radio Electrique (CISPR), etc, have provided standard for controlling the EM wave environments and for the countermeasure of the electromagnetic compatibility (EMC). In this paper, the status of EMW absorbers and the goal of smart EMW absorber in the future were described. Furthermore, design method of the smart EM wave absorber with heat radiating function was suggested. The designed smart EM wave absorber has the absorption ability of more than 20 dB from 2 GHz to 2.45 GHz band, the optimum aperture (hole) size, the adjacent hole space, and the thickness of which were 6 mm, 9 mm, and 6.5 mm, respectively. Thus, it is respected that these results can be applied as various EMC devices in electronic, communication, and controlling systems.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.364-374
• /
• 2016

With vast amounts of spectrum available in the millimeter wave (mmWave) band, small cells at mmWave frequencies densely deployed underlying the conventional homogeneous macrocell network have gained considerable interest from academia, industry, and standards bodies. Due to high propagation loss at higher frequencies, mmWave communications are inherently directional, and concurrent transmissions (spatial reuse) under low inter-link interference can be enabled to significantly improve network capacity. On the other hand, mmWave links are easily blocked by obstacles such as human body and furniture. In this paper, we develop a multi-hop relaying transmission (MHRT) scheme to steer blocked flows around obstacles by establishing multi-hop relay paths. In MHRT, a relay path selection algorithm is proposed to establish relay paths for blocked flows for better use of concurrent transmissions. After relay path selection, we use a multi-hop transmission scheduling algorithm to compute near-optimal schedules by fully exploiting the spatial reuse. Through extensive simulations under various traffic patterns and channel conditions, we demonstrate MHRT achieves superior performance in terms of network throughput and connection robustness compared with other existing protocols, especially under serious blockage conditions. The performance ofMHRT with different hop limitations is also simulated and analyzed for a better choice of the maximum hop number in practice.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.7-14
• /
• 1996

두께가 20mm와 30mm이고 폭이 40mm와 60mm 인 길이 600mm의 낙엽송 제재목에 응력파 시험과 휨강도 시험을 실시하였다. 모든 시험편은 생재 상태로 구입 후 함수율 약 13%로 조습 처리하여 응력파 시험과 휨강도 시험을 시행하였다. 휨 영계수와 휨강도는 두께가 큰 것이 작게 나타났다. 최상의 상관관계는 휨 영계수와 양 표면에서 구한 값의 평균값을 사용한 응력파 속도 및 영계수 사이에 나타났다. 휨 영계수와 관계에서 응력파 영계수는 응역파 속도 보다 더 확연한 옹이의 영향을 보였다.