• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1998년도 학술발표회 발표논문집
• /
• pp.382-387
• /
• 1998

Triaxial compression tests were run to study on the undrained strength characteristics of fiber mixed kaolin clay(Hadong). The influence of various test parameters such as amount and aspect ratio(ratio of length to diameter) of fiber, confining stress was also investigated. Test results showed that the increase in aspect ratio was increased in deviator stress at failure, but no effect on pore water pressure at failure. Deviator stress at failure was also increased at 0.5％ mixing ratio(weight fraction of fiber to that of soil solid) of fiber but it was, thereafter, decreased and wits reached to constant after 2％ mixing ratio. On the contrary, Pore water pressure at failure was increased as mixing ratio of fiber was greater than 1%. Deviator stress and pore water pressure of both clay and fiber mixed clay(FMC) at failure were increased as confining stress was increased. Deviator stress of FMC at failure was about 10％ larger than that of clay, but pore water pressure of FMC at failure was almost similar to that of clay.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2000년도 봄 학술발표회 논문집
• /
• pp.263-268
• /
• 2000

Recently, the recycling of the by-products was attempted to various fields. One of the major industry, the copper manufacturing industry produced a lot slags. in this study, the copper smelting slag was used to use practically application for the aggregate of concrete. To find the optimum mixing ratio of mortar with the copper smelting slag as substitution for sand, the mixing ratio was increased 1:2 to 1:5 step by step and every mixture was contained 5 steps sand substitutive ratio. The substitutive ratio of sand was increased 25% st대 by step from 0% to 100%. The result of this study was shown as follows. 1. In the every mixture, as the substitutive ratio was increased, the flow was decrease 3.64% from 18cm, and the unit content weigth was increased 5.5% in average. 2. The property of the strength was judged that it was more affected W/C and mixing ratio than the copper smelting slag.

• 한국식품조리과학회지
• /
• 제11권2호
• /
• pp.113-118
• /
• 1995

A preferable mixing ratio of a six-vegetable juice was suggested in this study. The vegetables used for preparation of mixed vegetable juice were carrot(Ct), cabbage(Cg), pear(Pr), cucumber(Cr), celery (Cy) and dongchimi(Di). The characteristics of pH, titratible acidity, reducing sugar, turbidity, solids, color and acceptability were compared to determine the mixing ratio. The vegetables showed a wide ranHe of pH of 3.70-6.01, acidity of 28.92 uv~74.40 nd and reducing sugar of 1.20ft~ 12.69fo. Celery juice showed the higest suspension stability and "b" value and the lowest values in Hunter "L" and "a" values among the 6 vegetable juice. The preferable mixing ratio of two-vegetable juice selected were Ct-Di(1 : 4), Cg-Pr(1 : 3) and Cr-Cy(3 : 1). From the various ratio of the three of biary mixtures of Cg-Pr(1 : 3): Ct-Di(1 : 4): Cr-Sy(3 : 1), two ratio of 5.0 : 2.5 2.5(V-6A) and 6.0 : 2.0 : 2.0(V-6B) were suggested as the most prefered six-vegetable juice. Pear, dongchimi and cucumber were found to be influential on the preference. The pH and titratible acidity of the two juices with different ratios were in the range of 4.92~4.98 and 36.g∼37.4 ml, respectively.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2007년도 춘계학술대회논문집
• /
• pp.285-297
• /
• 2007

As the demands of environment protection increase, the pulp mold container is developed to substitute for the plastic cushion materials like EPS(expanded poly styrene). The water-absorbing ratio, tensile strength and compressive strength of pulp mold are important factors to evaluate its shock absorbing characteristics. The study was performed to investigate the effects of the mechanical property changes on the various conditions of temperature and relative humidity for pulp mold containers made of mixed materials on ONP(old newspaper) and OCC(old corrugated container). This study also is evaluated the optimized mixing ratio of materials for making pulp mold by analyzing the changes of physical properties according to a various procured temperature and relative humidity conditions. The results show that the water absorption ratio of sample increased significantly, and tensile strength decreased $20{\sim}30%$, compressive strength decreased $10{\sim}20%$ by increasing relative humidity condition. And the results show that the ONP 50% and OCC 50% was optimized mixing ratio according to the samples.

• 한국연소학회지
• /
• 제20권3호
• /
• pp.21-26
• /
• 2015

This study was performed to provide the information of the combustion characteristics of n-butanol fuel in accordance with the n-heptane fuel mixing ratio. The closed homogeneous reactor model was used for the analysis. The analysis conditions were set to 800 K of the initial temperature, 20 atm of initial pressure and 1.0 of equivalence ratio. The results of analysis were compared in terms of combustion temperature, combustion pressure, CO, Soot and $NO_X$ emissions. The results of combustion and exhaust emission characteristics showed that ignition delay was decreased and the combustion temperature was increased as the n-heptane mixing ratio was increased. Also, the carbon monoxide(CO) was slightly decreased however, the soot and nitrogen oxides($NO_X$) increased a little in accordance with the n-heptane fuel mixing ratio. In addition, the pressure difference was almost the same in any conditions.

• 플랜트 저널
• /
• 제6권2호
• /
• pp.70-77
• /
• 2010

This study investigated the characteristics of co-combustion of mixed anthracite (domestic and Vietnam) and bituminous coal (Sonoma, Australia) at circulating fluidized bed boiler in Donghae thermal power plant when mixing ratio of bituminous coal is variable. Co-combustion of bituminous coal contributes to improvement in general combustion characteristics such as moderately retaining temperature of furnace and recycle loop, reducing unburned carbon powder, and reducing discharge concentration of NOx and limestone supply owing to improvement in anthracite combustibility as the mixing ratio was increased. However, bed materials were needed to be added externally when the mixing ratio exceeded 40% because of reduction in generating bed materials based on reduction in ash production. When co-combustion was conducted in the section of 40 to 60% in the mixing ratio while the supplied particles of bituminous coal was increased from 6 mm to 10 mm, continuous operation was shown to be possible with upper differential pressure of 100 mmH2O (0.98 kPa) and more without addition of bed materials for the co-combustion of mixed anthracite and bituminous coal (to 50% or less of the ratio) and that of domestic coal and bituminous coal (to 60% of the ratio).

• Journal of Biosystems Engineering
• /
• 제37권2호
• /
• pp.100-105
• /
• 2012

Purpose: Methane production potential in aerobic digestion was assessed according to feed to inoculum (F/I) ratio for food waste only, and mixing ratio of two materials for food waste and swine manure to give a basic data for the design of anaerobic digestion system. Methods: Anaerbic digestion test was performed using a lab scale batch reactor at $35^{\circ}C$ for six different feed to inoculum (F/I) ratios (0.50, 0.72, 1.14, 1.50, 2.14 and 3.41), three food waste to swine manure ratios (100:0, 60:40 and 40:60) with two different loading concentrations (10g VS/L and 30g VS/L). Results: For food waste only, the highest biogas yield of 1008 mL/gVS was obtained at 0.50 of F/I. For the co-digestion of food waste and swine manure mixture, the highest biogas yield of 1148 mL/gVS was obtained at a mixing ratio of 40:60 with loading concentration of 10g VS/L. Conclusions: F/I ratio for the food waste only, mixing ratio of food waste and swine manure, and co-substrate loading rate affected the biogas production rate. For the low loading rate, there was not so much difference according to the mixing ratio of food waste and swine manure, but for the high loading rate higher biogas yield was acquired for the co-digestion of food waste and swine manure than for the food waste alone (mixing ratio, 100:0).

• 한국건설순환자원학회논문집
• /
• 제10권4호
• /
• pp.514-522
• /
• 2022

본 연구에서는 시멘트 복합체에 시멘트계 재료로 구성된 자기치유 캡슐을 적용하여 콘크리트 구조물의 자기치유 성능을 향상시키기 위한 연구의 일환으로 PCC(Powder Compacted Capsule) 크기 및 혼입율에 따른 모르타르의 공학적 특성을 비교ㆍ분석하였다. 이를 위해 PCC 크기 및 혼입율에 따른 모르타르의 유동성, 압축강도, 하중재부하 시험, 탄산화, 초음파속도, 투수 특성 등을 측정하였다. 측정 결과, PCC의 혼입율이 증가할수록 유동성과 압축강도가 증가하였으며, 치유특성 검토를 위해 진행한 하중재부하 시험의 경우 03PC 배합에서 PCC 혼입율이 증가할수록 치유율이 증가하였다. 정수위투수 시험의 경우 PCC를 사용할 경우 유출수량 감소율이 Plain 배합에 비해 최대 35 % 높은것으로 나타났으며, 크기 0.3~0.6 mm의 PCC를 15 % 혼입할 시 모르타르의 균열 치유율 향상에 효과적인 것으로 나타났다.

• Journal of Welding and Joining
• /
• 제23권1호
• /
• pp.41-47
• /
• 2005

Arc pressure is one of important factors in understanding physical arc phenomena. Especially it affects on the penetration, size and shape of TIG welding. Some researches were reported on the effect of arc pressure in low and middle current region. But there are not any research in high current region. The purpose of this study is to investigate the arc pressure distribution with mixing ratio of shield gas such as Ar and He gases. A Cu block with water cooling was specifically designed and used as an anode electrode in order to measure the arc pressure in high current region. Then, the arc pressure distribution was measured with change in welding current and mixing ratio of shield gases. The arc force was obtained by numerically integrating the measured results. As the results, it was shown that the arc pressure was concentrated at the central part of the arc in middle and high current regions when a pure Ar gas was used. In case of Ar + He mixing gas, the arc pressure was much lower than that of pure Ar gas. In addition, it was widely distributed to radial direction.

• 대한기계학회논문집B
• /
• 제40권1호
• /
• pp.47-53
• /
• 2016

격자 볼츠만법을 이용하여 리튬이온전지의 전극 내 발생하는 전해액 함침 현상에 관하여 연구하였다. 최근 리튬이온전지는 용량 증가 및 에너지밀도 향상을 위하여 전극 설계시 활물질에 미세입자를 혼합하고 있어, 이로 인하여 전해액 함침성에 영향을 미치게 될 수 있다. 본 연구에서는 활물질 혼합율에 따른 전해액 분포와 포화도 변화를 알아보았다. 활물질 혼합비의 변화는 전극 내 전해액 함침 메커니즘에 영향을 주어, 전해액 함침속도와 함침도가 변화함을 확인하였다.