• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2372-2377
• /
• 2007

Characteristics of turbulent lifted flames in coflow jets with the varying initial temperature have recently been investigated about only propane case diluted by nitrogen. The investigation has firstly improved a premixed flame model and a large scale mixing model among competing theories on the stabilization mechanism of turbulent flame to be suitable for a high temperature condition. In this research, about methane with good availability to apply for a practical combustor as clean fuel, its characteristics of turbulent nonpremixed flame have been studied experimentally. The results have shown an effectiveness of the premixed flame model and the large scale mixing model considered initial temperature variation. Additionally, considering the axial distance where the mean fuel concentration falls below the stoichiometric level along the center line of the jet according to diluting nitrogen, the premixed flame model have more accurately been improved.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권5호
• /
• pp.265-269
• /
• 2000

$(Ba, Sr)TiO_3$thin films were etched with a magnetically enhanced inductively coupled plasma (MEICP) at different CF4/Ar gas mixing ratios. Experimental was done by varying the etching parameters such as rf power, dc bias and chamber pressure. The maximum etch rate of the BST films was $1800{AA}/min$ under $CF_4/(CF_4+Ar)$ of 0.1, 600 W/350 V and 5 mTorr. The selectivity of BST to Pt and PR was 0.6, 0.7, respectively. X-ray photoelectron spectroscopy (XPS) results show that surface reaction between Ba, Sr, Ti and C, F radicals occurs during the (Ba, Sr)TiO3 etching. To analyze the composition of surface residue after the etching, films etched with different CF_4/Ar$ gas mixing ratio were investigated using XPS and secondary ion mass spectroscopy (SIMS).

• Transactions on Electrical and Electronic Materials
• /
• 제18권2호
• /
• pp.74-77
• /
• 2017

In this work, we investigated the etching characteristics of TaNO thin films and the selectivity of TaNO to $SiO_2$ in an $O_2$/CF4/Ar inductively coupled plasma (ICP) system. The maximum etch rate of TaNO thin film was 297.1 nm/min at a gas mixing ratio of O2/CF4/Ar (6:16:4 sccm). At the same time, the etch rate was measured as a function of the etching parameters, such as the RF power, DC-bias voltage, and process pressure. X-ray photoelectron spectroscopy analysis showed the efficient destruction of the oxide bonds by the ion bombardment, as well as the accumulation of low volatile reaction products on the etched surface. Based on these data, the ion-assisted chemical reaction was proposed as the main etch mechanism for the $CF_4$-containing plasmas.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2000년도 춘계학술대회 논문집 전자세라믹스 센서 및 박막재료 반도체재료 일렉트렛트 및 응용기술
• /
• pp.52-55
• /
• 2000

In this study, (Ba,Sr)$TiO_3$(BST) thin films were etched with a magnetically enhanced inductively coupled plasma(MEICP) as a function Ar/$CF_4$ gas mixing ratio. Experiment was done by varying the etching parameters such as rf power, dc bias voltage and chamber pressure. The maximum etch rate of the BST films was 1700 ${\AA}/min$ under $CF_4/(CF_4+Ar)$ of 0.1, 600 W/350 V and 5 mTorr. The selectivity of BST to Pt and PR was 0.6, 0.7, respectively. X -ray photoelectron spectroscopy(XPS) studies shows that there are surface reaction between Ba, Sr, Ti and C, F radicals during the etching. To analyze the composition of surface residue remaining after the etching, films etched with different $CF_4$/Ar gas mixing ratio were investigated using XPS.

• 한국분무공학회지
• /
• 제2권1호
• /
• pp.18-28
• /
• 1997

The present study is mainly aiming at numerically analyzing the combustion and emission characteristics of the diesel spray in a high-pressure environment. Computations are peformed for the peak chamber pressure with range from 4.08 MPa to 162 MPa. Numerical results indicate that the pressure increase in combustion chamber significantly influences the mechanism for droplet dynamics and mixing characteristics, spray penetration autoignition, flame lift-on height and the propagation or fuel vapor and flame. By increasing the ratio or the ambient density to injected liquid density, the fuel-air mixing rates and the burning rates increase and the $NO_x/soot$ emission level decreases.

• 대한전자공학회논문지
• /
• 제25권6호
• /
• pp.694-699
• /
• 1988

Optical phase conjugate mechanism and edge enhancement by degenerate four wave mixing (DFWM) in photorefractive material are described, and image reconstruction is perfromed sucessfully in BaTiO3 single crystal. Also, the edge enhancement is carried out in the crystal by the same DFWM geometry. But the intensities of three incident beams are inverted. Good quality of edge enhancement is observed in real-time (processing time 10 sec) with low incident light intensity (5.38mW/cm\ulcorner.

• Ocean Science Journal
• /
• 제40권2호
• /
• pp.101-107
• /
• 2005

A simple analytical model is considered in an attempt to demonstrate a formation mechanism of the abyssal current in the East Sea. In this model, the abyssal currents are driven by wind through an outcrop region and flow along closed geostrophic contours. A rough estimate of the abyssal currents, arrived at by applying this model to the region of deep mixing in the East Sea, gives currents comparable to those observed, although there is an uncertainty in the surface area of the outcrop region. It seems that the spin-up of deep water by wind forcing through the region of deep winter mixing is, at least partly, an important contribution to the formation of the abyssal currents in the East Sea.

• 유변학
• /
• 제10권3호
• /
• pp.152-159
• /
• 1998

폴리카보네이트와 스티렌-아크릴로니트릴 공중합체의 블렌드를 이축 압출기에서 용 융혼련할 경우의 분산혼련 작용기구를 연구하였다. 분산상 형성에 관계되는 지배적인 과정 은 sheet, lace 및 ligament 생성에 이어 Rayleigh 형태의 불안정성에 기인한 구형의 분산상 (droplet) 형성으로 확인되었다. 분산상과 연속상의 점도비와 분산상의 크기에 대한 상관관 계의 조사에서는 주어진 점도비의 범위에서 점도비 약 70인 경우를 제외하고는 거의 무관한 관계를 나타내었으며 이는 이축 압출기의 강력한 혼련요소인 kneading 부위에서 주어지는 연신 흐름장에 의한 영향을 반영한 것으로 해석되었다. 분산상의 최종크기는 오히려 분산상 들간의 coales-cence 정도에 크게 영향을 받았으며 연속상의 점도가 상대적으로 낮은 경우 에 동일한 분산상에 대한 coalescence 정도가 심화되어 분산상의 크기가 증가되었다.

• Macromolecular Research
• /
• 제13권1호
• /
• pp.30-38
• /
• 2005

Sulfur-cured gum natural rubber vulcanizates were devulcanized using two different concentrations of diallyl disulfide. The devulcanization process was performed at $110^{\circ}C$ min in an open two-roll cracker-cum-mixing mill. Natural rubber vulcanizates having various sulfur/accelerator ratios were used to study the cleavage of monosulfide, disulfide, and polysulfide bonds. The properties of devulcanized natural rubber increased upon increasing the disulfide concentration and the mechanical properties of the revulcanized natural rubber increased upon decreasing the sulfur content in the original rubber vulcanizates. The scorch time and the maximum state of cure both increased when the ground vulcanizates were treated with higher amounts of disulfide. TGA and DMA were conducted to study the effects of the devulcanization on the thermal stability and the $T_g$ behavior of the vulcanizates. SEM analysis was conducted to study how the failure mechanism was affected by the devulcanization process. It was possible to recover $70-80\%$ of the original gum rubber properties by using this process. From IR spectroscopic analysis, we observed that the oxidation of the main chains did not occur during high-temperature milling.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2002년도 추계 학술대회논문집
• /
• pp.127-132
• /
• 2002

Numerical and experimental works have been made in order to figure out the physical mechanism of thermal storage system for the determination of optimal design and to enhance the thermal efficiency of the system. To this end a computer program is developed and evaluated successfully against experimental data measured with a bench scale facility. Considering the thermal efficiency of storage is critically impaired by the mixing effect, the minimum flow mixing situation is calculated by the assumption of uniform plug-type flow as a reference condition. Further a parametric systematic calculations have been made for a hypothetical full-scale storage system with Fr, storage dimension, diffuser type and loading hour, etc.