• Journal of the Optical Society of Korea
• /
• v.16 no.3
• /
• pp.313-317
• /
• 2012

We have evaluated a 1.3 ${\mu}m$ vertical-cavity surface-emitting laser (VCSEL), whose bottom mirror and central active layer were grown by metal organic chemical vapor deposition (MOCVD) and whose top mirror was covered with a dielectric coating, for 10 Gb/s data transmission over single-mode fibers (SMFs). Successful demonstration of error-free transmission of the directly modulated VCSEL signals at data rate of 10 Gb/s over a 10 km-long SMF was achieved for operating temperatures from $20^{\circ}C$ to $60^{\circ}C$ up to bit-error-rate (BER) of $10^{-12}$. The DC bias current and modulation currents are only 7 mA and 6 mA, respectively. The results indicate that the VCSEL is a good low-power consuming optical signal source for 10 GBASE Ethernet applications under controlled environments.

• Journal of Surface Science and Engineering
• /
• v.49 no.3
• /
• pp.231-237
• /
• 2016

This article reports a new chemical bath for preparing a mirror-like surface of AZ31 Mg alloy. In order to find an appropriate chemical polishing solution, four different acidic solutions of sulphuric acid, nitric acid, acetic acid and a specially designed mixture of nitric acid and acetic acid were investigated in view of the changes in surface appearance, roughness and dissolution rate of AZ31 Mg alloy. The surface scales on AZ31 Mg alloy were readily removed by all the acidic solutions, but a reflective surface was produced only by etching in the specially designed solution, and only after a specific etching time. The surface roughness increased with etching time in sulphuric acid, nitric acid, and acetic acid, but it lowered after a specific etching time in the specially designed mixture of nitric acid and acetic acid. Dissolution rate of the alloy in the specially designed mixture of nitric acid and acetic acid appeared to be more than twice than that in separate nitric acid or acetic acid. In this work, we recommend the mirror-like surface of AZ31 Mg alloy obtained by polishing for an optimum time in a mixture of nitric acid and acetic acid for following surface finishings, chemical conversion coating, electroplating, electrophoretic painting and anodizing treatment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.421.2-421.2
• /
• 2016

고효율 태양전지에서 후면 반사 방지막은 장파장대(900nm~1200nm) 빛의 내부 반사를 증가시켜 광흡수도를 개선한다. 태양전지 후면에 박형 절연층 구조를 구성함으로써 특정 파장에서 높은 반사도를 얻을 수 있는 Bragg mirror 구조를 이론적으로 계산할 수 있다. Bragg mirror 구조를 이용하여 태양전지의 후면 반사층(Rear reflector layer)을 형성함으로써 태양전지 내부의 광흡수도를 개선할 수 있다. 후면 반사 방지막(Rear anti-reflection coating)으로 사용되는 Al2O3와 SiOxNy 또는 이러한 두 가지 물질의 겹층 구조를 구성하여 장파장대 빛의 반사도 차이에 의한 광흡수도 개선 정도를 광학 시뮬레이션을 통해 계산하였다. 광학 시뮬레이션은 TCAD를 이용하였으며 두 가지 겹층 구조에서 각 반사 방지막의 두께에 따른 단락 전류(Jsc)의 개선 정도, 후면 반사층 두께의 최적화 조건을 계산하였다. 후면 반사방지막을 제외한 기본적인 태양전지 구조는 n-type PERC 구조를 사용하였으며, 후면 반사방지막만의 광학적 특성을 살펴보기 위해 전극은 광학적으로 투명하다고 가정하였다. 반사방지막 두께의 범위는 Al2O3(5-30nm), SiNx(150-300nm), SiOxNy(150-300nm)에서 수행하였으며, 각각 1nm, 2nm 간격으로 진행하였다. Al2O3/SiOxNy 구조에서는 단락 전류가 32.45-32.87mA/cm2 값을 가진다. Al2O3/SiNx 구조에서는 단락 전류가 32.59-32.87mA/cm2 값을 가진다. 결론적으로, 후면 반사방지막의 겹층 구조를 통해 광흡수도를 증가 시킬 수 있으며, TCAD 시뮬레이션을 통하여 입사되는 태양광 스펙트럼에 최적화된 구조를 설계할 수 있다.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.3
• /
• pp.419-425
• /
• 2020

In this paper, when a refractive index grating and a gain grating are simultaneously present in a DFB (Distributed Feedback) laser for a 1.55 um wavelength with two mirror surfaces without an anti-reflective coating, an analysis program was developed to determine the beam distribution of the oscillation mode in the longitudinal direction. As the phases of the index and gain gratings on the mirror faces are varied, the lasing gain and the beam profiles |R(z)| and |S(z)| of the lasing mode with the emitted power ratio P_l/P_r are analyzed and examined in case of δL<0. In order to reduce the threshold current of a oscillation mode and enhance the frequency stability, κL should be greater than 8, regardless of the grating phase values at the mirror surface.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.354-361
• /
• 2005

In high speed cutting process, due to the friction between the tool and workpiece, a temperature rise of contacting part is serious. It need to develop cutting tool for overcoming such a poor condition. So now, some studies, the optimization of tool shapes, the fine grains of tool material, multi-layer coating of tools are processing. If mirror finishing on the tool is processed, there is advantage of relation between chip and tool, because of less friction, and also tool's lift would be increased. As a result mirror like finishing is expected efficient enhancement of tool. Generally, it is too difficult to process by a general way for tools of complex shapes, it is required a new method to process such complex shape tools. The magnetic fluid polishing technique can polish the workpiece of complex shape, because the polishing method which polishes as compress the workpiece by the magnetism abrasives to arrange to the linear according to the line of magnetic force. In this paper, We polished the surface of the high speed cutting tool using the magnetic fluid polishing technique, to enhance the performance of the high speed cutting tool.

• The Journal of the Convergence on Culture Technology
• /
• v.8 no.5
• /
• pp.483-488
• /
• 2022

In this paper, when a gain grating and a refractive index grating exist simultaneously in a DFB laser diode having a wavelength of 1.55 ㎛, an anti-reflection coating is applied to the right mirror surface so that ρ_r=0. In case of δL<0, the characteristics of the oscillation frequency and oscillation gain have been analyzed. Whenever the phase of the grating on the left side of the mirror continuously decreases by π/2, the δL value of each oscillation mode decreases by about 0.6 to the left of the graph lines of each oscillation mode. The case of the oscillation mode having the lowest threshold gain is the case of κL=10, and in this case, the mode selectivity is relatively low compared to the case of other values of κL. From κL=0.1 to κL=6, the mode selectivity and the frequency stability are excellent. As the mode selectivity is excellent, the frequency stability is excellent. Compared to the case with two cleaved mirrors, the DFB laser diode with anti-reflection coating increases the threshold gain of the oscillation mode by about 2 times, but the mode selectivity becomes about 2 times better.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2003.11a
• /
• pp.128-128
• /
• 2003

Electrochromism (EC) is defined as a phenomenon in which a change in color takes place in the presence of an applied voltage. Because of their low power consumption, high coloration efficiency, EC devices have a variety of potential applications in smart windows, mirror, and optical switching devices. An EC devices generally consist of a transparent conducting layer, electrochromic cathodic and anodic coloring materials and an ion conducting electrolyte. EC has been widely studied in transition metal oxides(e.g., WO$_3$, NiO, V$_2$O$\sub$5/) Among these materials, WO$_3$ is a most interesting material for cathodic coloration materials due to its lush coloration efficiency (CE), large dynamic range, cyclic reversibility, and low cost material. WO$_3$ films have been prepared by a variety of methods including vacuum evaporation, chemical vapor deposition, electrodeposition process, sol-gel synthesis, sputtering, and laser ablation. Sol-gel process is widely used for oxide film at low temperature in atmosphere and requires lower capital investment to deposit large area coating compared to vacuum deposition process.

• ETRI Journal
• /
• v.24 no.5
• /
• pp.341-348
• /
• 2002

We propose an asymmetric sampled grating laser and a multi-wavelength laser array associated with it. Asymmetric sampling periods combined with an index shifter make it possible to use first order reflection for lasing operations. With the structure of our design, we achieved a simple fabrication procedure as well as a high yield without using complex and time-consuming e-beam lithography for multi-period gratings. We analyzed the effect of mirror coating by numerical analysis to improve single mode and power extraction performance. By using high reflection-antireflection coatings, we obtained high power extraction efficiency without degradation of the single mode property. For the multi-wavelength laser array, to gain wavelength control, we varied the sampling periods from one laser to an adjacent laser across the array. With this approach, we showed the feasibility of an array of up to 30 channels with 100 GHz wavelength spacing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.5
• /
• pp.20-28
• /
• 2014

The high velocity oxygen fuel spraying (HVOF) is a kind of surface modification process technology to form the sprayed coating layer after spraying the powder to molten or semi-molten state by the ultra-high speed at the high-temperature heat source and conflicting with a substrate. It is desirable to melt completely the thermal spray powder in order to produce the coating layer with an optimal adhesion, however, because a semi-molten powder in a spray process has the low efficiency and become a factor that degrades the mechanical property by the inducement of pore-forming within the coating layer. To improve the wear resistance, corrosion resistance and heat resistance, in this study, the plungers of high-speed and ultra-high pressure reciprocating hydraulic pumps for oil and water used in ironwork are produced with $420J_2$ and the coating layers of plungers are formed by the powders of WC-Co-Cr and WC-Cr-Ni including the high hardness WC. The surface of these plungers is modified by the super-mirror face grinding machine using variable air pressure developed in this laboratory, and then the characteristics of cross-sectional microstructure, and surface roughness and hardness values between no operation and 100 days-operation are examined and made a comparison. The fine tops and bottoms on surface roughness curve of oil-hydraulic pump plunger sprayed by WC-Cr-Ni are molded more and higher than those of water-hydraulic pump sprayed by WC-Co-Cr because the plunger diameter of oil-hydraulic pump is 0.4 times smaller than that of water-hydraulic pump and the pressure of oil-hydraulic pump exerted on the plunger is operated with the 70 bars higher than that of water-hydraulic pump. As a result, it is found that the values of centerline average surface roughness and maximum height for oil-hydraulic pump plunger are bigger than those of water-hydraulic pump plunger.

• The Journal of the Convergence on Culture Technology
• /
• v.6 no.4
• /
• pp.727-732
• /
• 2020

In this paper, when a refractive index grating and a gain grating were simultaneously present in a DFB laser having a wavelength of 1.55 ㎛, a dielectric film coating was applied so that reflection did not occur on the right mirror surface, so that 𝜌_r=0. In case of δL > 0, the threshold gain and the beam distribution in the longitudinal direction and the radiated power ratio P_l/P_r of the oscillation mode were compared for the cases of the phase of 𝜌_l=π and π/2. If the phase of 𝜌_l=π, in order to obtain a low threshold current and high frequency stability, κL should be greater than 8. In the case of the phase of 𝜌_l= π/2, when κL is larger than 4.0, the oscillation gain starts to be lower than when the phase of 𝜌_l=π. In order to lower the threshold current of a oscillation mode and enhance the frequency stability, κL should be greater than 8.