• 대한기계학회논문집A
• /
• 제26권8호
• /
• pp.1585-1590
• /
• 2002

This paper reports on the balance weight effect on the lubrication and friction characteristics of crankshaft system. To determine the main bearing loads, the crankshaft was treated as statically determinate system. Four and eight-balance weight crankshafts were considered, and minimum oil film thickness and friction loss were calculated. The main bearing loads were increased in the four-balance shaft due to the increasing of unbalanced rotating mass at No. 1 and 3 main bearing sides. The minimum oil film thickness of four-balance shaft became thinner than eight-balance, and friction loss was increased.

• 대한기계학회논문집A
• /
• 제25권8호
• /
• pp.1183-1188
• /
• 2001

This paper reports on the starved lubrication for the piston ring. In this analysis, two types of inlet boundary conditions, fully flooded and starved condition, are considered at the leading edge. The inlet position of effective lubrication and squeeze term are obtained by numerically iterative method. The effective lubricated region is reduced due to the starved condition at the inlet. The starved condition at the inlet significantly reduced the minimum oil film thickness(MOFT) at the midstroke of piston, and the friction force is also increased due to the thin oil film thickness. In the starved conditions, the power loss is significantly increased.

• Tribology and Lubricants
• /
• 제19권2호
• /
• pp.85-93
• /
• 2003

In this study, a multigrid multi-integration method has been used to solve the steady-state, elastohydrodynamic lubrication (EHL) point contact problem of a ball joint mechanism used in small reciprocating compressors. Pressure and film thickness profiles have been calculated at minimum and maximum Moes M parameter conditions during one revolution of crankshaft. The effects of various lubricant viscosities, loads, ball velocities, elastic modulli, and radii of curvature on the calculated pressure distribution and film thicknesses have been investigated. The results indicate that the viscosity of lubricant, the sliding velocity of ball, and the reduced radius of curvature have considerable effects on the minimum and central film thicknesses. Solutions obtained with the multigrid analysis are compared with results calculated according to the Hamrock ＆ Dowson relations for the minimum and central film thicknesses.

• Tribology and Lubricants
• /
• 제31권5호
• /
• pp.213-220
• /
• 2015

This study evaluates the effect of grooves on the stem part of a plunger on the lubrication characteristics of a fuel injection pump (FIP) by using hydrodynamic lubrication analysis. The current study uses the two-dimensional Reynolds equation to evaluate the changes in lubrication characteristics with variations in clearance, viscosity, and grooves for a laminar, incompressible, and unsteady state flow. This study investigates the lubrication characteristics by comparing the dimensionless minimum film thickness or the film parameter, which is the ratio of the minimum film thickness to surface roughness. The analysis method for the groove section differs depending on the depth of the groove. For instance, in the case of a shallow groove, the film thickness equation considers the depth of the groove, while in the case of a deep grove, it considers the flow continuity. The lubrication characteristics of the FIP are more sensitive to changes in the groove width than to changes in other design variables. Moreover, the application of a groove is more effective under low viscosity conditions. The smaller the distance from the edge of the stem part to the first groove in the case of shallow grooves, the better are the lubrication characteristics of the FIP. In contrast, in the case of deep grooves, the lubrication characteristics of the FIP improve as the distance increases. The application of shallow grooves is more effective for improving the lubrication characteristics than the application of deep grooves.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.36-41
• /
• 2004

The purpose of this paper is analyzing the oil film pressure distribution and the minimum oil film thickness for a connecting rod bearing using an A VL's EXCITE program. It is very important to understand optimized oil supplying holes and oil groove dimensions for supporting sufficiently inertia forces and gas pressures from the combustion chamber for a Diesel engine. The computed results indicate that the optimized oil groove width of a bearing and oil hole of a journal are recommended for high performance of a connecting rod bearing at the elastohydrodynamic lubrication zone. These results as design parameters are very useful data for a bearing designer as a firm reference of an automotive engine.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.34-34
• /
• 2004

The purpose of this paper is analyzing the oil film pressure distribution and the minimum oil film thickness for a connecting rod bearing using an A VL′s EXCITE program. It is very important to understand optimized oil supplying holes and oil groove dimensions for supporting sufficiently inertia forces and gas pressures from the combustion chamber for a Diesel engine. The computed results indicate that the optimized oil groove width of a bearing and oil hole of a journal are recommended for high performance of a connecting rod bearing at the elastohydrodynamic lubrication zone. These results as design parameters are very useful data for a bearing designer as a firm reference of an automotive engine.

• 한국진공학회지
• /
• 제7권4호
• /
• pp.300-305
• /
• 1998

rf magnetron sputtering 증착법으로 Al2O3(0001)기판위에 적층생장시킨 Pt박막의 결정성 및 이의 구조적 특성을 backscattering spectrometry(BS)/channeling, transmission electron microscopy(TEM)등을 이용해 분석하였다. $MeV^4$He ion channeling 결과, 증착시 기판의 온도가 $600^{\circ}C$, 증착된 Pt층의 두께가 3500$\AA$이었을 때 최소산란수율(channeling minimum yield)이 4%인 결정성이 우수한 Pt박막이 생장되었음을 확인하였으며, 동일한 증 착조건하에서 증착된 Pt층은 $Al_2O_3$(0001)기판위에 6중 대칭구조를 지닌(111)면방향으로 적층 생장되었으며, (111)면방향을 중심으로 대칭적인 원자배열 구조를 갖고 있는 쌍정구조를 형 성하고 있었다. 단면 TEM 분석결과에서도 격자부정합에 의한 strain을 감소시키기 위하여 형성된 쌍정을 관찰할 수 있었으며 strain이 집중되는 쌍정경계면에서 표면거칠기의 증가 또는 관찰되었다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 춘계학술대회 및 공장견학
• /
• pp.39-53
• /
• 1993

The minimum oil film thickness(MOFT) in the connecting-rod bering of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film charactrtistics. And cylinder pressure, crank-pin surface temperature and bearing tenp ture are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable detmuuination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Tribology and Lubricants
• /
• 제10권1호
• /
• pp.14-26
• /
• 1994

The minimum oil film thickness(MOFT) in the connecting-rod bearing of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film characteristics. And cylinder pressure, crank-pin surface temperature and bearing temperature are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable determination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Journal of the Optical Society of Korea
• /
• 제18권3호
• /
• pp.236-243
• /
• 2014

Surface profiling and film thickness measurement play an important role for inspection. White light interferometry is widely used for engineering surfaces profiling, but its applications are limited primarily to opaque surfaces with relatively simple optical reflection behavior. The conventional bucket algorithm had given inaccurate surface profiles because of the phase error that occurs when a thin-film exists on the top of the surface. Recently, reflectometry and white light scanning interferometry were combined to measure the film thickness and surface profile. These techniques, however, have found that many local minima exist, so it is necessary to make proper initial guesses to reach the global minimum quickly. In this paper we propose combing reflectometry and white light scanning interferometry to measure the thin-film thickness and surface profile. The key idea is to divide the measurement into two states; reflectometry mode and interferometry mode to obtain the thickness and profile separately. Interferogram modeling, which considers transparent thin-film, was proposed to determine parameters such as height and thickness. With the proposed method, the ambiguity in determining the thickness and the surface has been eliminated. Standard thickness specimens were measured using the proposed method. Multi-layered film measurement results were compared with AFM measurement results. The comparison showed that surface profile and thin-film thickness can be measured successfully through the proposed method.