• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.20 no.5
• /
• pp.71-77
• /
• 2020

Recently, the tracking radar has confirmed the necessity of developing a small tracking radar that can be operated without various restrictions in various environments. In addition, the performance of a small tracking radar requires equal to or higher than the existing tracking radar. Such a small tracking radar can be implemented through miniaturization and low power of existing tracking radar. In this paper, the role and function of a signal processor for a small tracking radar are defined and we proposed a method to increase the efficiency of power consumption and miniaturization by minimizing the use of devices required to implement a signal processor for a small tracking radar. Used as a method for miniaturization, a device processor such as DDC and communication controller was implemented in an FPGA to design a signal processor for a small tracking radar. In addition, a low-power signal processor was designed by a power supply using a highly efficient switching regulator. Finally, the signal processor was verified by the performance test of the signal processor for the small tracking radar implemented, the Doppler tracking test using the signal processor on the small tracking radar, and the distance tracking test.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.265-274
• /
• 2011

In this paper, it is studied on wide radiating slot antenna's miniaturization for ultra wide-band(UWB) technologies and notch structure to prevent interference between UWB systems and existing wireless systems for using Wi-Fi service of IEEE standards 802.11 a/n. Proposed antenna that wide slot is decreased from $\lambda/2$ to $\lambda/4$ length of resonant frequency has decreased by 72 % compared with conventional antenna. And optimized T-shaped CPW-fed stub has satisfied UWB bandwidth for 3.0~11.8 GHz. Then, creating 2-order Hilbert curve slot line in the stub's patch area, 4.9~5.6 GHz that centered frequency is 5 GHz is eliminated. Finally, the designed antenna constructed on FR4-epoxy has $20{\times}15\;mm^2$ dimension. The measured results that are obtained return loss under -10 dB through 3.2~11.8 GHz without Wi-Fi bandwidth, a linear phase characteristic, a stable group delay, and omnidirectional radiation patterns are presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.62-62
• /
• 2008

As micro-system move toward higher speed and miniaturization, requirements for embedding the passive components into printed circuit boards (PCBs) grow consistently. They should be fabricated in smaller size with maintaining and even improving the overall performance. Miniaturization potential steps from the replacement of surface-mount components and the subsequent reduction of the required wiring-board real estate. Among the embedded passive components, capacitors are most widely studied because they are the major components in terms of size and number. Embedding of passive components such as capacitors into polymer-based PCB is becoming an important strategy for electronics miniaturization, device reliability, and manufacturing cost reduction Now days, the dielectric films deposited directly on the polymer substrate are also studied widely. The processing temperature below $200^{\circ}C$ is required for polymer substrates. For a low temperature deposition, bismuth-based pyrochlore materials are known as promising candidate for capacitor $B_2Mg_{2/3}Nb_{4/3}O_7$ ($B_2MN$) multi layers were deposited on Pt/$TiO_2/SiO_2$/Si substrates by radio frequency magnetron sputtering system at room temperature. The physical and structural properties of them are investigated by SEM, AFM, TEM, XPS. The dielectric properties of MIM structured capacitors were evaluated by impedance analyzer (Agilent HP4194A). The leakage current characteristics of MIM structured capacitor were measured by semiconductor parameter analysis (Agilent HP4145B). 200 nm-thick $B_2MN$ muti layer were deposited at room temperature had capacitance density about $1{\mu}F/cm^2$ at 100kHz, dissipation factor of < 1% and dielectric constant of > 100 at 100kHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.6 s.121
• /
• pp.591-601
• /
• 2007

In this paper, the miniaturized radio frequency identification(RFID) tag antennas used in UHF band$(908.5{\sim}914MHz)$ are designed and fabricated by using the circular loop antenna(CLA). Miniaturization of CLA was possible to transform the structure of circular loop into the structure of meander line. In the case of double meander line CLA is reduced up to 83% compared with the general type CLA. The $S_{11}$, -10 dB bandwidth, and gain of double meander line CLA were -11.9 dB, 12 MHz(1.3%), and -1.18 dBd. Also, a small half-wavelength CLA using double meander line is designed and fabricated for flat snack bag coated aluminum. The antenna is reduced up to 92.1% except ground. It shows the $S_{11}$ of -16.5 dB, -10 dB bandwidth of 48 MHz(5%) and gain of -0.58 dBd. The radiation pattern shows omni-directional pattern in z-y plane(x-axis pol.). Through this result, we can confirm that miniaturized type CLAs using meander lines are suitable for miniaturized RFIB tag antennas with the UHF band.

• Journal of IKEEE
• /
• v.23 no.1
• /
• pp.14-21
• /
• 2019

In this paper, we implemented an on-board miniaturization antenna operating 2.4 GHz using MZR(Mu Zero Resonator). It is must be operating under the constraint that the size of the small terminal PCB should be $78{\times}38{\times}0.8mm^3$ and the size of the system should be $63{\times}38{\times}0.8mm^3$ and the size of the radiating part should be $15{\times}38{\times}0.8mm^3$. The feeding structure uses a CPW structure for stable feeding and a feeding point at the upper left of the system board. A magnetic field coupling structure is used for coupling the feeding part and the antenna. The resonance frequency of the MZR is determined by the series inductance and capacitance of the cell, so the gap between the cells, the length of the cell, the length of the interdigital capacitor, and the spacing between the radiation part and the ground plane are analyzed. The antenna was designed and fabricated using the results. The total size of the antenna including the feed structure is $20.8{\times}9.0{\times}0.8mm^3$, and the electrical length is $0.1664{\lambda}_0{\times}0.072{\lambda}_0{\times}0.0064{\lambda}_0$. The measurement result for 10 dB bandwidth, gain and directivity are 440 MHz(18.3%), 0.4405 dB, and 2.722 dB respectively. It is confirmed that the radiation pattern has omnidirectional characteristics and it can be applied to ultra small terminal antenna.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.5B no.3
• /
• pp.262-266
• /
• 2005

In this paper, in order to enhance thrust of slotless type Permanent Magnet Linear Synchronous Motor, an optimal design is achieved by combining a genetic algorithm with 3D space harmonic method. In the case of multi-objective functions, the ratio of thrust/weight and thrust/volume are increased by $\7.56[%]l\;and\;7.98\[%]$, respectively. Thus, miniaturization and lightweight were realized at the same time.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2609-2612
• /
• 2003

This paper describes a 64 channel signal generator/analyzer module that is useful for verification and testing of digital circuits. It can perform logic analyzer function and signal generator function at the same time. The 64 Channel module is implemented with single FPGA chip for miniaturization, and an USB interface is used to increase portability of the module. Multiple modules can be used in parallel for the verification of large scale circuits. Moreover, since the module is implemented as a PC based system, one can configure convenient GUI(Graphic User Interface) environment.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1999.12a
• /
• pp.93-99
• /
• 1999

It is definite trend that the functional devices are to be integrated by miniaturizing of individual components. Bulk crystals turn into wafer form, while thin film of the functional materials is being fabricated for single and multi-layer devices. In addition, single crystals with multi-function performance would be desirable for further miniaturization. crystal growers have the responsibility for synthesis single crystals work to meet ever increasing requirement of future devices.

• International Journal of Internet, Broadcasting and Communication
• /
• v.4 no.1
• /
• pp.1-2
• /
• 2012

A speaker is a system which produces sound through electromechanical operations. It transforms electronic signals into audible sound signals. Almost all speakers are three dimensional. These days, many mobile electronic devices such as mobile electronic devices have become smaller and thinner. A problem with this miniaturization, however, is that the volume of speakers has also decreased. In contrast to conventional three dimensional speakers, we have invented a new type of two dimensional flexible speaker by utilizing the reverse piezoelectric effect.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.379-382
• /
• 2004

Microoptics has become the key technology in liquid crystal display systems due to its capabilities of miniaturization and design flexibility. We successfully demonstrate five different microoptical components for enhancing the image quality, providing better functions, increasing light efficiency, and generating 3D images in LCD applications.