• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.793-799
• /
• 2004

In track a third weakness point is joint part, turnout part, curve part. One of them joint part of rail have been known to the most weak point by loosen of joint bar and fish bolt due to impulse and vibration by wheel contact at times. In addition happen to deformation and failure at end of rail, failure and miniature of ballast gravel. Finally impact between wheel and rail become origin cause of a welded rail, noise and vibration. riding condition deterioration, besides track failure. In the present domestic, Thermite and Gas pressure weldings have been used to continuous welded rail(CWR), however stiffness and confidence in quality is lower than Flash butt welding method. FRW have the excellent capacity, however have a shortcoming large scale of machine and power equipment. Therefore we will introduce Mobile Flash Butt Welder can weld in track.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1280-1285
• /
• 2004

Microsystem technology has been applied to space technology and became one of the enabling technology by which low cost and high efficiency are achievable. Micro propulsion system is a key technology in the miniature satellite because micro satellite requires very small and precise thrust force for maneuvering and attitude control. In this paper research on micro solid propellant thruster is reported. Micro solid propellant thruster has four basic components; micro combustion chamber, micro nozzle, solid propellant and micro igniter. In this research igniter, solid propellant and combustion chamber are focused. Micro igniter was fabricated through typical micromachining and evaluated. The characteristic of solid propellant was investigated to observe burning characteristic and to obtain burning velocity. Change of thrust force and the amount of energy loss following scale down at micro combustion chamber were estimated by numerical simulation based on empirical data and through the calculation normalized specific impulses were compared to figure out the efficiency of combustion chamber.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2621-2624
• /
• 2008

The study on the measurement method of the aerodynamic performance of a turbo compressor was conducted. It is well known that the performance and the efficiency of the compressor can be calculated from the temperature and pressure distribution in each stage of the compressor. In the past Pitot tubes and thermocouples were used to measure pressure and temperature respectively, and recently pressure and temperature rake is used in order to decrease the measuring time and the number of measurement. The miniature total pressure rake which is available in the compressor with a small axial gap is designed and is under development.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2160-2164
• /
• 2008

Miniature Joule-Thomson cryocoolers have been widely used for rapid cooling of infrared detectors, probes of cryosurgery, thermal cameras, missile homing head and guidance system, due to their special features of simple configuration, compact structure and rapid cool-down characteristics. The cool-down time, the temperature at the cold end, the running time and the gas consumption are the important indicators of the performance of the J-T cryocooler. In this study, the initial cool-down stages of the J-T cryocooler were investigated by numerical simulations. The results show the effects of the initial charging pressures of gas on the cool-down time and the temperature at the cold end and the gas consumptions.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.640-645
• /
• 2007

An experimental apparatus to show the hot spot cooling of an IC chip using a thermoelectric cooler is developed. The spot heating in very small area is achieved by the applying CO$_2$ laser source and temperatures are measured using miniature thermocouples. The active effects of thermoelectric cooler on the hot spot cooling system such as rapid heat spreading in the chip and lowering the peak temperature around the hot spot region are investigated. The experimental results are simulated numerically using the TAS program, which the performance characteristics such as Seebeck coefficient, electrical resistance and thermal conductivity of the thermoelectric cooler are searched by trial and error. Good agreements are obtained between numerical and experimental results if the appropriate performance data of the thermoelectric cooler are given.

• Nuclear Engineering and Technology
• /
• v.45 no.7
• /
• pp.979-986
• /
• 2013

Uranium metal particle dispersion plates have been proposed as targets for Molybdenum-99 (Mo-99) production to improve the radioisotope production efficiency of conventional low enriched uranium targets. In this study, uranium powder was produced by centrifugal atomization, and miniature target plates containing uranium particles in an aluminum matrix with uranium densities up to 9 $g-U/cm^3$ were fabricated. Additional heat treatment was applied to convert the uranium particles into UAlx compounds by a chemical reaction of the uranium particles and aluminum matrix. Thus, these target plates can be treated with the same alkaline dissolution process that is used for conventional $UAl_x$ dispersion targets, while increasing the uranium density in the target plates.

• International Journal of Ocean System Engineering
• /
• v.1 no.1
• /
• pp.32-36
• /
• 2011

EG/AD/S type model ice was originally selected as the primary model ice material for the MOERI ice tank in Korea. The existence of a sugar component in the EG/AD/S mixture may cause a serious maintenance problem. In order to understand the influence of sugar in the original model ice, a series of tests with EG/AD/S and EG/AD model ices were performed, and their material properties compared. Because the target strength of model ice in the full-scale MOERI ice tank is expensive and difficult to control, tests were performed under cold room conditions using a miniature ice tank. This paper describes the material properties of EG/AD/S and EG/AD model ices, such as flexural strength, compressive strength and elastic modulus. In order to obtain the desired strength and stiffness levels for the model ice, a warm-up process was introduced.

• Mycobiology
• /
• v.45 no.4
• /
• pp.426-429
• /
• 2017

A yeast-like organism was isolated from a urine sample of a 6-year-old neutered male miniature poodle dog with urinary tract infection, diabetes ketoacidosis, and acute pancreatitis. We identified the yeast-like organism to be Candida glabrata and found that this fungus was highly resistant to azole antifungal drugs. To understand the mechanism of azole resistance in this isolate, the sequences and expression levels of the genes involved in drug resistance were analyzed. The results of our analysis showed that increased drug efflux, mediated by overexpression of ATP transporter genes CDR1 and PDH1, is the main cause of azole resistance of the C. glabrata isolated here.

• Vacuum Magazine
• /
• v.1 no.3
• /
• pp.14-20
• /
• 2014

Lithography is widely recognized as one of the key steps in the manufacture of ICs and other devices and/or structures. However, as the dimensions of features made using lithography become smaller, lithography is becoming a more critical factor for enabling miniature IC or other devices and/or structures to be manufactured. As explained above, to make it happen, many other important technologies will have to be addressed. The vacuum technology is one of them and the engineers and experts are paying attention on vacuum technology including vacuum pumps. Especially high Vacuum(HV) and Ultra high vacuum(UHV) are not easy and not simple one. So the manpower who can understand vacuum technology with long experience in vacuum industry is important with basic study.

• Proceedings of the Korean Information Science Society Conference
• /
• 1999.10a
• /
• pp.406-408
• /
• 1999

썬에 의해 자바 플랫폼이 소개된 후, 자바 기술은 네트워크 상에 연결된 장치들이 선택할 수 있는 하나의 플랫폼으로 자리를 잡았다. 그래서 자바 기술을 자원 제약적인 네트워크 디바이스 및 디지털 전자기기에 적용하고자 하는 연구가 계속해서 진행 중이다. 본 논문에서는 자바 가상 기계를 소형화할 수 있는 기법들을 연구 분석하고, 처리 능력이나 메모리의 크기에 제약이 있는 디바이스들에 사용 가능하고, 동적 컴파일링 기법을 적용하여 실행 효율을 높일수 있는 소형 자바 가상 기계를 설계하고자 한다.