• Tribology and Lubricants
• /
• v.20 no.1
• /
• pp.7-13
• /
• 2004

High strength steels are widely used as tribo-materials in the field. Previous study revealed that for mild steel, the states of strain on the worn surface measured by X-ray diffraction has a good relationship with the state of wear. The objective of this study is to identify the relationship between the state of strain on the worn surface and the state of wear in high strength steels. Sliding wear tests were carried out using several hardened steels. X-ray diffraction tests were conducted to analyze the state of strain on the worn surface during wear. The experimental results indicated that the state of strain on worn surface in the hardened steel shows the same tendency as in the mild steel. It is clear that change of half value width on the worn surface as a function of sliding speeds is broadly similar in shape to wear characteristics curve and its magnitude has a good relationship with the wear rate at two different wear modes in the hardened steel.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.153-154
• /
• 2002

Wear map of silver coatings on AISI 52100 has been constructed to delineate the wear transition behavior with the change in operating conditions in various environments. Three main regimes were clearly identified: (i) elastic/plastic deformation of silver coating without failure. (ii) mild wear regime after initial failure of silver coating and (iii) severe wear regime. In the mild wear regime, the contact surfaces were covered with transfer layers of agglomerated wear particles. The transfer layer acted as a protective layer and resulted in low friction even after the initial failure of the coated films, whose characteristics were strongly dependent on both the operating and environmental conditions. Also, the existence of the critical sliding speed, above which no transfer layer was able to form, was discussed in the work.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1404-1411
• /
• 1993

This study was undertaken to investigate the corrosive wear charateristics upon various transformation condition of austempered low-alloy ductile cast iron in corrosive environments against mating specimen made of the hardened SM45C. The corrosive wear test was carried out by rubbing the annular surface of two test pieces in distilled water and aqueous solution at constant sliding speed of 0.5m/s. In severe wear region, the corrosive wear rate Wc increased hastily with NaCl concentration owing to intermetallic adhesion but Wc went down slowly in mild wear region due to lubricating effect of the corrosion product. The critical sliding distance decreased with increasing NaCl concentration due to increased generation rate of the corrosion product and the specific corrosive wear rate has maximum in 1% NaCl aqueous solution at mild wear region. With the variation of matrix, the corrosive wear resistance of the fine acicular bainite was higher than that of coarse upper bainite because of reducing the local cell reaction by carbides. A growth in volume fraction of retained austenite in matrix increased the Wc due to soften surface, but has a declining tendency of Wc in mild wear region.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.199-200
• /
• 2002

Three-body abrasive wear resistance of mild steel, low alloy steel (Bisalloy) and 27%Cr white cast iron was investigated using a ball-cratering test. Glass beads, silica sand, quartz and alumina abrasive particles with sizes larger than $100{\mu}m$ were used to make slurries. It was found that the wear rates of all three materials tested increased with time when angular abrasive particles were used and were rather constant when round particles were used. This increase in wear rates was mainly due to the gradual increase in ball surface roughness with testing time. Abrasive particles with higher angularity caused higher ball surface roughness. Mild steel and Bisalloy were more affected by this ball surface roughness changes than the hard white cast iron. Generally, three-body rolling wear dominated. The contribution of two-body grooving wear increased when the ball roughness was significant. More grooves were found when round particles were used or the size of the particles was decreased.

• Tribology and Lubricants
• /
• v.10 no.3
• /
• pp.29-38
• /
• 1994

The friction and wear of mild steel at dry sliding surfaces under different vacuum conditions have been investigated to understand the wear mechanisms. For the test, a ball-ondisk typed wear-rig has been built and implemented, allowing control of sliding speed, load and vacuum. Results show that, at a high sliding velocity, friction of low carbon steel (SS41) under a high vacuum is much higher than that of ambient condition and wear is much severer. It is due to lack of effective oxidation film formation on which steel surfaces could protect themselves against the severe wear. It has been shown, however, that there is a critical regime with contact conditions (at a low sliding velocity, a low load, and under a medium vacuum) at which effective, protective films of low carbon steel have been built on the surfaces in a friction process with a self-regulating way, resulting in both very low coefficients of friction (about 0.3) and mild wear. In order to investigate the protective films on steel surfaces, the worn surfaces and the wear debris have been experimentally analyzed with SEM, AES/SAM and XRD. A theoretical analysis of frictional heating at sliding surfaces, and an experimental analysis of the influence of oxidation wear under various vacuum conditions are described. The important variables on which self-formations of protective films at dry sliding surfaces depend, and the wear mechanisms are also investigated.

• Journal of Embryo Transfer
• /
• v.25 no.3
• /
• pp.201-206
• /
• 2010

Two male reticulated giraffes (Giraffa camelopardalis reticulata), 21-year-old, died of nutritional deficiency that primarily caused by serious tooth wear at Seoul Zoo in winter. A 970 kg-weighed giraffe showed tooth wear of premolars, molars and incisors at necropsy. A foreign body in the rumen, congestion and ulcer of abomasum and duodenum were also observed. Mild appearance of serous fat atrophy in pericardial sac suggests that lack of nutritional intake caused by tooth wear can become harmful enough to threat life. At the necropsy of a 1,290 kg-weighed giraffe, a large quantity of sandy soil were found in the rumen which would stuck the pathway of well-fermented ruminal contents at esophageal groove. Nutritional deficiency could be suspected to urge this giraffe to graze grass on the ground along with sandy soil. Secondarily, the soil damaged teeth and become a culprit making irregular tooth wear and mild serous fat atrophy. Nutritionally good care of geriatric animals is needed especially for browsing animals like giraffes and critically in winter season.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1988.06a
• /
• pp.28-30
• /
• 1988

윤활시스템에서 마모는 상대적인 운동을 하는 두 물체사이에서 표면상태, 접촉조건 및 분위기등의 제요소들에 의해 발생되며, 형태학적으로 scuffing, scoring, pitting 및 fretting 등으로 분류된다. 윤활조건의 특성에 따라 미끄럼 접촉에서는 mild wear, severe wear로 구분되며, 이들의 마모 생성기구의 차이는 접촉상대속도, 하중 및 표면조도등의 정도에 기인된다. mild wear에서 severe wear 영역으로 전이될 때의 가혹한 조건에서 생성되는 마모현상을 scuffing wear라 하며, 이는 접촉면에서의 표면돌기의 직접접촉에 의한 cold welding 현상, 즉 local welds의 특성을 지닌 마멸형태로 정의한다. 이의 생성은 접점간의 하중 및 미끄럼 속도가 증가됨에 따라 온도상승에 기인되어 순간적으로 발생된 마찰열이 그 원인이 있으며, 기어, cam 및 tappet, 피스톤링 및 실린더 라이너 등의 마멸현상이 대표적인 예이다.

• Tribology and Lubricants
• /
• v.2 no.1
• /
• pp.39-45
• /
• 1986

Wear simulation test have been conducted in mild, severe and transient wear regions by a four-ball wear tester. Wear particles are separatively deposited by the RPD technique, and quantitatively analysed in terms of wear particles size distribution. Characteristics of the wear particle size distribution are compare to the results of wear tests through both weibull parameters and center moment method of the weibull distribution function.

• Journal of the Korean Society for Heat Treatment
• /
• v.9 no.4
• /
• pp.261-270
• /
• 1996

Boriding is one of the chemical methods to achieve the case hardening of steel as well as nitriding or carburizing. The surface layer of the borided steel shows higher hardness and exhibits better resistance to corrosion or fatigue than the nitrided or carburized steel. The great majority of previous studies were confined to mild steel or some alloy steel. To enlarge the application, ductile cast iron (DCI) as a material for boriding has been tried in this study. Thus, sliding wear test has conducted using a pin-on-disc machine to compare between borided DCI and mild steel in fluidized bed furnace. The results show that the wear resistance of borided DCI is improved. Especially it is more efficient in the case of occurence of the mechanical wear.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.10 no.6
• /
• pp.89-94
• /
• 2011

The wear characteristics between nonmetal and metals have been investigated using a disc on disc system. The specimens of nonmetal are made by the nylon and teflon materials. The specimens of the metal are used as eight kinds of along their hardness. The kinds of metals are copper(Hv96), aluminum(Hv186), brass(Hv234), aluminum bronze(Hv294), stainless steel(Hv327), annealing mild steel(Hv345), mild steel(Hv372), Hard steel(Hv434). In this study, a upper and lower specimens have been used the same size and shape. Using experimental data we figured the relationship between friction coefficient of nonmetal and metals. We figured the relationship between friction temperature of nonmetal and metals. The result had been verified a wear characteristics of nonmetal and metals in the wear tests.