• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1121-1127
• /
• 2010

This paper describes the equivalent circuit of $45^{\circ}$ layer, one of $11.25^{\circ}$, $22.5^{\circ}$, and $45^{\circ}$ phase shift layers, which are needed for X-band Radant lens 4-bit phase shifter. The equivalent circuit is extracted by comparing the CST's MWS results with the Agilent's ADS results for $45^{\circ}$ phase shift layer. The simulated result is compared with the measured one. Using the extracted equivalent circuit, the phase bit simulation results of 4-bit Radant lens are also presented.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.4
• /
• pp.559-565
• /
• 2008

This study designed a new type of loop antenna that is able to detect partial discharges based on microstrip line technology. In the diagnosis of power cables, partial discharge signals are generally produced at a frequency range less than 100MHz because high frequency PD signals are lost along a propagation path in such cables. The new type of loop antenna sensor has been studied using simulation software known as CST microwave studio version 5.0. In partial discharge measurement experiments, a commercial HFCT sensor was used as a reference sensor. Several experiments were made over HFCT and loop antenna sensors for detecting partial discharges on 22.9kV MV XLPE cable. In this study, we showed the loop antenna designed in this study that can be applied as a commercial HFCT sensor.

• Journal of Advanced Navigation Technology
• /
• v.15 no.2
• /
• pp.189-196
• /
• 2011

In order to subsitute for the normal mode helical wire antenna, bent monopole antenna combined with a helical structure is proposed as a kind of printed antenna. The antenna which can be operated at 418MHz has been simulated and designed by use of a commercial EM simulator Microwave Studio(MWS). It has been observed that the proposed antenna has good agreements between simulated results and measured results such as the return loss and the radiation pattern. The proposed antenna has been applied practically to the wireless remote controller operationg at 418MHz. It has been observed that the use of the proposed antenna result in similar antenna performance from view point of radiation power when compared with the use of the previous normal mode helical antenna.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.184-184
• /
• 2012

We proposed a new measurement method of cutoff probe using the reactance spectrum of the plasma in cutoff probe system instead of transmission spectrum. The high accurate reactance spectrum of the plasma which is expected in previous circuit simulation of cutoff probe [1] was measured by using the automatic port extension method of the network analyzer. The measured reactance spectrum is good agreement with E/M wave simulation result (CST Microwave Studio). From the analysis of the measured reactance spectrum based on the circuit modeling, not only the electron density but also electron-neutral collision frequency can be simply obtained. The obtained results of electron density and e-n collision frequency were presented and discussed in wide range of experimental conditions, together with comparison result with previous methods (a previous cutoff probe using transmission spectrum and a single langmuir probe).

• Journal of electromagnetic engineering and science
• /
• v.11 no.2
• /
• pp.97-104
• /
• 2011

A planar slotted waveguide array antenna has been designed at 9.37 GHz for X-band radar applications. The antenna consists of multiple branchline waveguides with broadwall radiating shunt slots and a main waveguide to feed the branch waveguides through a series of inclined coupling slots. The antenna feed point is located at the center of the main waveguide. Element weights in the array have been calculated bysampling a continuous circular Taylor aperture distribution at the 25 dB sidelobe level in both the E and Hplanes. A commercially available electromagnetic (EM) simulation tool has been used to characterize the individual isolated slot and that data hassubsequently been used to design the planar array. The array is finally analyzed in a CST Microwave studio and the measured and simulated results have been found to be in good agreement.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.1
• /
• pp.131-137
• /
• 2011

This paper analyzes EM(Electromagnetic) characteristic in the high voltage connector for the hybrid electric vehicle. The connector bridges the electrical components and helps transferring electrical power and signal through it. The necessity of the high voltage and current connector development is emphasized because the hybrid electric vehicle recently uses the high voltage and current more than 500V and 80A. So far there has not been international EMC (Electromagnetic Compatibility) standards to limit the RE(Radiation Emission) from the connector for the hybrid electric vehicle. In this paper we analyzed EM characteristic of the 288V, 65A connector to check if the RE from the high voltage connector could be within the RE limit standard of vehicle. Three-dimensional modeling and simulation was conducted by using MWS(Microwave Studio) of the CST corporation, and the result was compared with the measured RE data, which showed good coincidence each other.

• International journal of advanced smart convergence
• /
• v.4 no.2
• /
• pp.29-33
• /
• 2015

In this paper, we propose the method to improve the performance of the antenna system that contains three bands, such as Lte3G, WLAN and Lte4G. This antenna has an advantage that can cover the three different frequency bands 2.1GHz, 2.4GHz and 2.6GHz through one antenna design. The design and simulations are done using CST Microwave Studio 2014 program. The antenna is designed by using the FR-4 (lossy) substrate with the dielectric constant of er=4.3 and dielectric loss tangent 0.025. The substrate dimensions are the following; Thickness[h] is 1.6mm, Length is 90mm, and Width is 40mm. The ground is designed by using the PEC material with h=0.035mm. The patch is designed by using the copper with h=0.035mm. In the near future, we will fabricate the antenna, which we have designed, and then apply this antenna to the mobile communication system. And we will test this mobile communication system for the diverse environments.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.45-51
• /
• 2009

The propagation characteristics in parallel plate waveguide with dielectric layer having periodic metal strip pattern are investigated. PIN diode ON/OFF states are regarded as the short and open circuit, respectively, in the simulation using CST's MWS. The $11.25^{\circ}$, $22.5^{\circ}$, and $45^{\circ}$ layers which can be used for X-band 4-bit Radant lens phase shifter, are designed. The simulated results for each dielectric layer are $11.28^{\circ}$, $23.2^{\circ}$, and $46.22^{\circ}$, respectively. Also, the equivalent circuit of each layer at the operating band is realized and simulated using Agilent's ADS. The ADS simulated results are compared with the MWS simulated ones. Measured differential phase shills at the center frequency are $9.6^{\circ}$, $22.4^{\circ}$, and $43^{\circ}$, respectively.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.949-956
• /
• 2005

In this paper, a new CPW-fed cross shape fractal antenna having a self-affinity is presented. This novel configuration, which has anisotropic scaling symmetry, makes smaller profile characteristic compared to the fractal antenna using a self-similarity. Increase of the iteration coefficient, which leads to decrease of the fundamental resonant frequency, shows a good impedance matching condition and multi-band characteristics due to new surface current paths. The radiation patterns are similar to those of monopole antennas. In the K3 stage of iteration, the proposed antenna shows a measured maximum gain 2.27 dBi at 940 MHz. A commercially available software based on the FDTD algorithm has been used to obtain the predicted results. In addition, an RT/Duroid 5880 substrate has been employed for the experimental results.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2018.05a
• /
• pp.445-448
• /
• 2018

In this paper, we design microstrip antenna for GPS / WiFi for broadband mobile communication. The proposed antenna is designed to be used in the FR-4 (er = 4.3), the size is $40mm{\times}50mm$, and it can be used in the GPS frequency band of 1.6GHz and the WiFi frequency band of 5GHz. 2014, and the simulation result shows that the gain is 1.909dB at 1.6GHz and 4.607dB at 5GHz. The S-parameter also showed a result of less than -10dB (WSWR2: 1) in the desired frequency band. Recently, it is expected that GPS navigation system, which is widely used in smart phones and tablet PCs, can be easily and conveniently used by combining and applying GPS with WiFi.