• Journal of the Korean Ceramic Society
• /
• v.34 no.6
• /
• pp.583-590
• /
• 1997

The effects of Mn2O3 and Y2O3 additives on the microstructure and dielectric properties of Sr(Zr, Ti)O3 have been investigated. Powders with Sr(Zr1-xTix)O3(0$\leq$x$\leq$0.1) composition were prepared by the conventional solid state processing from commercial TiO2 and precipitation-processed ZrO2. The powders containing sintering additives of Mn2O3 and Y2O3 were compacted and then sintered at 1,55$0^{\circ}C$ for 4 h to get>97% relative density. Mn2O3 suppressed the grain growth and Y2O3 enhanced the density of sintered body. The oxidation state of Mn ions were determined by a chemical wet method and EPR spectroscopy. Mn ions were present as Mn2+ and Mn4+ in SrZrO3, while as Mn3+ and Mn4+ in Ti-substituted Sr(Zr, Ti)O3. With the substitution of Ti, the lattice parameters of SrZrO3 decreased and its dielectric constant increased with remarkable decrease in Q value. The dielectric constant of Sr(Zr, Ti)O3 was in the range of 30 to 40, Q values 1,200~5,400 at 6 GHz and temperature coefficient of resonant frequency -67~100 ppm/K.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.58-63
• /
• 2000

For the microwave high density devices and modules of the 3D configuration, we proposed radial stub for the ground connection. The proposed structure is analyzed by the full-wave analysis of finite element method (FEM) and characterized experimentally. The results show that the return loss is more than 15 dB and the insertion loss is less than 0.5 dB in the frequency range from 2.5 GHz to 6.3 GHz. The proposed grounding scheme will be useful for the ground connection lot the microwave high density devices and module of 3D configuration.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.7 no.1
• /
• pp.15-20
• /
• 2012

In this paper, we designed and analysed K-band front-end module for digital microwave communication system receiver which improvement of dynamic range. We also suggested method of minimum amplified input signal level used to minimize noise figure of low-noise amplifier for High dynamic range. The designed modules consist of active mixer with conversions gain and PL-DRO with high stability and quality factor. The designed modules performance is that has the characteristics of over 54dB conversion gain, 1.3dB noise figure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.922-929
• /
• 2007

In this paper, a rectangular loop array antenna for beam scanning is designed. A program using RWG MoM(Rao Wilton Glisson Method of Moment) is developed for SEP(Scan Element Pattern) theoretically. Simulation results obtained by using a commercial software tool, MWS are compared with the MoM results to confirm the validity of the program. Also these results are compared with the measured ones for the case of an $8{\times}5$ subarray. The fabricated $8{\times}5$ subarray showed a flat gain characteristic in the elevation scan range of ${\pm}45^{\circ}$ in the E-plane.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.2
• /
• pp.333-338
• /
• 2008

In this paper, a new NMOS current-mirror type bridge rectifier for driving RFID chips, whose minimum input voltage required to obtain the effective DC output voltage is low enough and whose power dissipation can be reduced than that of conventional one, is proposed. The designed rectifier is able to supply high enough and well-rectified DC voltages to drive RFID transponder chips for the frequency range of 13.56 MHz HF(for ISO 18000-3), 915 MHz UHF(fur ISO 18000-6), and 2.45 GHz microwave(for ISO 18000-4). Output characteristics of the proposed rectifier are analyzed with the high frequency equivalent circuit. And the circuitry method for effective reducing of the gate leakage current due to the increasing of operating frequency is also proposed theoretically. Using this method, the power consumption of $100\;{\mu}W$ and the DC output voltage of 2.13V for 3V peak-to-peak input voltage and $45\;K{\Omega}$ load resistance are obtained. Compared to conventional one, the proposed rectifier operates in more stable and shows superior characteristics in UHF and microwave frequencies.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.6 no.3
• /
• pp.80-90
• /
• 1995

The scattering parameters of a microstrip single line, a right-angle bend and a coupled line are calculated using the multiport network model for the frequency range from 1 to 18 GHz. The single line is analyzed using the planar waveguide model. The right-angle bend is broken into two rectangular segments, and each segment is analyzed in a similar fashion as the single line. Impedance matrices corresponding to the two segments are combined by the segmentation method. In the analysis of elec- tromagnetic coupling of the coupled line, a new method is employed resulting in much less computation time than those previous methods involving Green's functions. A good agreement between the numerical results for the three structures and those from SuperCompact reveals the usefulness of the multiport network medel in analyzing complicated mirostrip single and coupled line discontinuities.

• Journal of the Korean Ceramic Society
• /
• v.35 no.10
• /
• pp.1078-1084
• /
• 1998

lanthanum chromite(LaCrO3) powder was synthesized by the combustion of a solution of metal nitrates La(NO3).6H2O and Cr(NO3)3.9H2O and urea. The pH of solution affected a yield of the combustion products but did not influence the morphology of the products. When the pH of the solution was in the range of 0.7-4, the yield of the combustion products was more than 90% The morphology of the combustion products was af-fected by heating methods for the solution. The hot-plate induced heating of the solution yielded powders hav-ing two-dimensionally interconnected agglomerates whereas microwave-induced heating produced a fine and non-agglomerated powders. The specific surface area(BET) of the combustion products using microwave-in-non-agglomerated powders. The specific surface area(BET) of the combustion products using microwave-in-duced heating method were larger(25~32m2/g) than that of hot plate heating method(10-14m2/g)

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2013.05a
• /
• pp.232-233
• /
• 2013

The unit-water content in fresh concrete determines consistency, and play an important role in condensing the structure of concrete and enhancing the durability of concrete. The capacitance measurement method measure quickly unit-water content and is the best way to apply to construction site. In this study, the unit-water content of capacitance measurement method is estimated according to types and replacemment ratio of admixture. and the field application of capacitance measurement method is reviewed.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.3
• /
• pp.391-395
• /
• 2007

MgO enhanced $(Ba_{0.6}Sr_{0.4})$ $TiO_3$ thick films have been fabricated by a tape casting and firing method for tunable devices on the microwave frequency band. In order to improve ferroelectric properties, the composite thick films enhanced with MgO on BST have been asymmetrically annealed by a focused halogen beam method. Dielectric constants of composite thick films are changed from 1050 to 1300 at 100 kHz after 60 s and 150 s annealing by the focused halogen beam. Even though no prominent changes were previously observed from the thick films before and after annealing in terms of chemical composition and surface morphology, it is clear that the average particle size of the thick films calculated by Scherrer's formula were increased by annealing. Furthermore, a strong correlation between particle size and dielectric constant of the composite thick films has been observed; dielectric constant increases with increased particle size. This has been attributed to the increased volume of ferroelectric domain due to increased particle sizes. As a result, the tuning range was improved by halogen beam annealing.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.420-426
• /
• 2023

We prepared a highly sensitive hydrogen (H₂) sensor based on Indium oxides (In₂O₃) porous nanoparticles (NPs) loaded with Platinum (Pt) nanoparticle in the range of 1.6~5.7 at.%. In₂O₃ NPs were fabricated by microwave irradiation method, and decorations of Pt nanoparticles were performed by electroless plating on In₂O₃ NPs. Crystal structures, morphologies, and chemical information on Pt-loaded In₂O₃ NPs were characterized by grazing-incident X-ray diffraction, field-emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, respectively. The effect of the Pt nanoparticles on the H₂-sensing performance of In₂O₃ NPs was investigated over a low concentration range of 5 ppm of H₂ at 150-300 ℃ working temperatures. The results showed that the H₂ response greatly increased with decreasing sensing temperature. The H₂ response of Pt loaded porous In₂O₃ NPs is higher than that of pristine In₂O₃ NPs. H₂ gas selectivity and high sensitivity was explained by the extension of the electron depletion layer and catalytic effect. Pt loaded porous In₂O₃ NPs sensor can be a robust manner for achieving enhanced gas selectivity and sensitivity for the detection of H₂.