• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.341-345
• /
• 2012

[Li0.055(K0.5Na0.5)0.945](Nb1-xTax)O3 (0.05 ≤ x ≤ 0.25) ceramics were prepared by the partial sol-gel (PSG) method to improve the microstructure homogeneity of Ta5+ ion and were compared to those prepared by the conventional mixed oxide (CMO) method. For the PSG method, Ta(OC2H5)5 was directly reacted with calcined [Li0.055(K0.5Na0.5)0.945]NbO3 powders and the specimens sintered at 1100 ℃ for 5 hrs showed a single phase with a perovskite structure. Compared to the specimens prepared by conventional mixed oxide powders, the relative ratio of tetragonal phase to orthorhombic phase of the sintered specimens prepared by Ta(OC2H5)5 was larger than that of the sintered specimens prepared by Ta2O5. The electromechanical coupling factor (kp), piezoelectric constant (d33) and dielectric constant (εr) of the sintered specimens were increased with Ta5+ content. These results could be attributed to the decrease of the orthorhombic-tetragonal polymorphic phase transition temperature (To-t), which could be evaluated by oxygen octahedral distortion. Strain of the sintered specimens prepared by the PSG method was higher than that of specimens prepared by the CMO method due to the increase of relative density. The effects of crystal structure on the strain characteristics of the specimens were also discussed.

• 한국건축시공학회지
• /
• 제23권4호
• /
• pp.381-392
• /
• 2023

본 연구에서는 산화 그래핀 나노플레이트릿(Oxidized graphene nanoplatelet, GO)와 유공유리분말(Hollow glass powder, HGP)를 활용한 초고강도 콘크리트의 역학특성을 검토하였으며 이를 위해 작업성, 강도(압축, 인장), 수밀성, 내부조직을 검토하였다. 그 결과 HGP 소량 투입으로 작업성능을 획기적으로 회복시킬 수 있었고 강도특성 및 수밀성도 증가하는 것으로 나타났다. cGO(C사의 GO) 와 HGP는 응집현상 없이 분산이 잘 되어 있는 것으로 확인되었고 공극량은 20% 이상 감소하는 것으로 나타났다. cGO와 HGP가 실리카 흄(Silica fume, SF)을 대체할 수 있는지에 대해서도 검토하였다. cGO와 HGP의 사용으로 SF 없이도 쉽게 작업성을 확보할 수 있었고 역학특성도 향상되는 것으로 나타났으며 신재료의 사용으로 콘크리트 제조방법의 변화가 가능함을 확인할 수 있었다.

• 소성∙가공
• /
• 제32권4호
• /
• pp.173-179
• /
• 2023

In this study, the age-hardening behavior and tensile properties of a cast AZ91-0.3Ca-0.2Y (SEN9) alloy are investigated and compared with those of a commercial AZ91 alloy. Even after homogenization heat treatment, the SEN9 alloy contains numerous undissolved secondary phases, Al₈Mn₄Y, Al₂Y, and Al₂Ca, which results in a higher hardness value than the homogenized AZ91 alloy. Under aging condition at 200 ℃, both the AZ91 and SEN9 alloys exhibit the same peak-aging time of 8 h, but the peak hardness of the latter (86.8 Hv) is higher than that of the former (83.9 Hv). The precipitation behavior of Mg₁₇Al₁₂ phase during aging significantly differs in the two alloys. In the AZ91 alloy, the area fraction of Mg₁₇Al₁₂ discontinuous precipitates (DPs) increases up to ~50% as the aging time increases. In contrast, in the SEN9 alloy, the formation and growth of DPs during aging are substantially suppressed by the Ca- or Y-containing particles, which leads to the formation of only a small amount of DPs with an area fraction of ~4% after peak aging. Moreover, the size and interparticle spacing of Mg₁₇Al₁₂ precipitates of the peak-aged SEN9 alloy are smaller than those of the peak-aged AZ91 alloy. The homogenized AZ91 alloy exhibits a higher tensile strength than the homogenized SEN9 alloy due to the finer grains of the former. However, the peak-aged SEN9 alloy has a higher tensile elongation than the peak-aged AZ91 alloy due to the smaller amount of brittle DPs in the former.

• 한국재료학회지
• /
• 제33권6호
• /
• pp.242-250
• /
• 2023

Titanium, which has excellent strength and toughness characteristics, is increasingly used in the aerospace field. Among the titanium alloys used for body parts, more than 80 % are Ti-6Al-4V alloys with a tensile strength of 931 MPa. The spark plasma sintering (SPS) method is used for solidification molding of powder manufactured by the mechanical milling (MM) method, by sintering at low temperature for a short time. This sintering method avoids coarsening of the fine crystal grains or dispersed particles of the MM powder. To improve the mechanical properties of pure titanium without adding alloying elements, stearic acid was added to pure titanium powder as a process control agent (PCA), and MM treatment was performed. The properties of the MM powder and SPS material produced by solidifying the powder were investigated by hardness measurement, X-ray diffraction, density measurement and structure observation. The processing deformation of the pure titanium powder depends on the amount of stearic acid added and the MM treatment time. TiN was also generated in powder treated by MM 8 h with 0.50 g of added stearic acid, and the hardness of the powder was higher than that of Ti-6Al-4V alloy when treated with MM for 8 h. When the MM-treated powder was solidified in the SPS equipment, TiC was formed by the solid phase reaction. The SPS material prepared as a powder treated with MM 8 h by adding 0.50 g of stearic acid also formed TiN and exhibited the highest hardness of Hv1253.

• 한국재료학회지
• /
• 제33권7호
• /
• pp.315-322
• /
• 2023

In the present work, we address the new route for the green synthesis of manganese dioxide (MnO₂) by an innovative method named the solution plasma process (SPP). The reaction mechanism of both colloidal and nanostructured MnO₂ was investigated. Firstly, colloidal MnO₂ was synthesized by plasma discharging in KMnO₄ aqueous solution without any additives such as reducing agents, acids, or base chemicals. As a function of the discharge time, the purple color solution of MnO₄^- (oxidation state +7) was changed to the brown color of MnO₂ (oxidation state +4) and then light yellow of Mn²⁺ (oxidation state +2). Based on the UV-vis analysis we found the optimal discharging time for the synthesis of stable colloidal MnO₂ and also reaction mechanism was verified by optical emission spectroscopy (OES) analysis. Secondly, MnO₂ nanoparticles were synthesized by SPP with a small amount of reducing sugar. The precipitation of brown color was observed after 8 min of plasma discharge and then completely separated into colorless solution and precipitation. It was confirmed layered type of nanoporous birnessite-MnO₂ by X-ray powder diffraction (XRD), fourier-transform infrared spectroscopy (FT-IR), and electron microscopes. The most important merits of this approach are environmentally friendly process within a short time compared to the conventional method. Moreover, the morphology and the microstructure could be controllable by discharge conditions for the appropriate potential applications, such as secondary batteries, supercapacitors, adsorbents, and catalysts.

• 한국재료학회지
• /
• 제33권7호
• /
• pp.285-294
• /
• 2023

Porous ceramics are used in various industrial applications based on their physical properties, including isolation, storage, and thermal barrier properties. However, traditional manufacturing environments require additional steps to control artificial pores and limit deformities, because they rely on limited molding methods. To overcome this drawback, many studies have recently focused on fabricating porous structures using additive manufacturing techniques. In particular, the binder jet technology enables high porosity and various types of designs, and avoids the limitations of existing manufacturing processes. In this study, we investigated process optimization for manufacturing porous ceramic filters using the binder jet technology. In binder jet technology, the flowability of the powder used as the base material is an important factor, as well as compatibility with the binder in the process and for the final print. Flow agents and secondary binders were used to optimize the flowability and compatibility of the powders. In addition, the effects of the amount of added glass frit, and changes in sintering temperature on the microstructure, porosity and mechanical properties of the final printed product were investigated.

• Geomechanics and Engineering
• /
• 제31권4호
• /
• pp.395-407
• /
• 2022

In this paper, cracks with different angles are prefabricated in rock specimens to study the fracture characteristics of rock based on CT images. The rock specimens are prepared for compression tests according to the standard recommended by ISRM (International Society for Rock Mechanics). The effects of different angles on rock mechanical properties and crack propagation fracture modes are analyzed. Then, based on the cohesive element method and CT images, the relationship between porosity and Young's modulus as well as the fracture property is explored by the numerical modelling. In the modelling, the distribution of Young's modulus is determined by the CT image through the field variable method. The results show that prefabricated cracks reduce the mechanical properties of rock. The closer the angles of the prefabricated crack is, the greater the Young's modulus of the rock sample is. The failure process of each specimen with prefabricated cracks is formed by the initiation and propagation of crack, and the angle of the prefabricated crack will affect the type of extended crack. As part of the numerical model proposed in this paper, the microstructure of rocks is reflected by CT images. The numerical results verify the effectiveness of the cohesive element method in the study of crack propagation for rock. The rock model in this paper can be used to predict engineering disasters such as collapse and landslide caused by rock fracture, which means that the methodology adopted in this paper is comprehensive and important to solve rock engineering problems.

• Fisheries and Aquatic Sciences
• /
• 제26권9호
• /
• pp.535-547
• /
• 2023

Sea cucumbers (Holothuria scabra), also known as beche-de-mer, are highly valued as a luxurious food item and have been utilized as a traditional tonic food in various Asian countries for centuries. The body walls of sea cucumbers are the main edible part, which are primarily composed of glycosaminoglycan (GAG). The rehydration of dried sea cucumber is a crucial step prior to further processing. The aim of this study was to assess the impact of ultrasound-assisted rehydration (UAR) on the quality of dried sea cucumbers. The experiment used four different rehydration methods, including conventional methods at 27℃ (KV27℃) and 15℃ (KV15℃), as well as a combination of ultrasound at 27℃ with conventional at 15℃ (UAR27 + KV15℃) and ultrasound at 15℃ with conventional at 15℃ (UAR15 + KV15℃). Results indicated that the rehydration rate (RR) was significantly affected by both the rehydration method and the temperature used (p < 0.05). UAR27 + KV15℃ was identified as the most effective method in terms of rehydration behavior and quality characteristics of dried sea cucumber, with a RR of 0.58 ± 0.53 gH₂O/hour and reduced rehydration time of up to 28 hours. Moreover, the UAR27 + KV15℃ method demonstrated superior rehydration potential, nutritional value (proximate composition and sulfate content), color, lower energy, and microstructure properties compared to the other methods. The sulfate content and yield of sulfated GAGs were determined to be 89.4 mg/g and 52.8 ㎍/g, respectively. Confirmation of the absorption band of the sulfate group showed the presence of 3-N-acetyl galactosamine at a wavelength of 1,269 cm^-1 and C-O-S at 860 cm^-1. The sea cucumbers treated with UAR exhibited a GAG content approximately 2.9 times higher than those rehydrated with the conventional method. Eventually, the combination of UAR at 27℃ with conventional at 15℃ methods can significantly accelerate the rehydration of sea cucumber without negatively affecting its physical quality properties.

• Steel and Composite Structures
• /
• 제49권4호
• /
• pp.361-380
• /
• 2023

A size dependent bending behavior of piezoelectrical flexoelectric layered perforated functionally graded (FG) composite nanobeam rested on an elastic foundation is investigated analytically. The composite beam is composed of regularly cutout FG core and two piezoelectric face sheets. The material characteristics is graded through the core thickness by power law function. Regular squared cutout perforation pattern is considered and closed forms of the equivalent stiffness parameters are derived. The modified nonlocal strain gradient elasticity theory is employed to incorporate the microstructure as well as nonlocality effects into governing equations. The Winkler as well as the Pasternak elastic foundation models are employed to simulate the substrate medium. The Hamiltonian approach is adopted to derive the governing equilibrium equation including piezoelectric and flexoelectric effects. Analytical solution methodology is developed to derive closed forms for the size dependent electromechanical as well as mechanical bending profiles. The model is verified by comparing the obtained results with the available corresponding results in the literature. To demonstrate the applicability of the developed procedure, parametric studies are performed to explore influences of gradation index, elastic medium parameters, flexoelectric and piezoelectric parameters, geometrical and peroration parameters, and material parameters on the size dependent bending behavior of piezoelectrically layered PFG nanobeams. Results obtained revealed the significant effects both the flexoelectric and piezoelectric parameters on the bending behavior of the piezoelectric composite nanobeams. These parameters could be controlled to improve the size dependent electromechanical as well as mechanical behaviors. The obtained results and the developed procedure are helpful for design and manufacturing of MEMS and NEMS.

• 한국분말재료학회지
• /
• 제30권6호
• /
• pp.463-469
• /
• 2023

Aluminum alloys, known for their high strength-to-weight ratios and impressive electrical and thermal conductivities, are extensively used in numerous engineering sectors, such as aerospace, automotive, and construction. Recently, significant efforts have been made to develop novel aluminum alloys specifically tailored for additive manufacturing. These new alloys aim to provide an optimal balance between mechanical properties and thermal/electrical conductivities. In this study, nine combinatorial samples with various alloy compositions were fabricated using direct energy deposition (DED) additive manufacturing by adjusting the feeding speeds of Al6061 alloy and Al-12Si alloy powders. The effects of the alloying elements on the microstructure, electrical conductivity, and hardness were investigated. Generally, as the Si and Cu contents decreased, electrical conductivity increased and hardness decreased, exhibiting trade-off characteristics. However, electrical conductivity and hardness showed an optimal combination when the Si content was adjusted to below 4.5 wt%, which can sufficiently suppress the grain boundary segregation of the α-Si precipitates, and the Cu content was controlled to induce the formation of Al₂Cu precipitates.