• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.2A
• /
• pp.147-152
• /
• 2005

In this paper, we have proposed a novel DGS(Defected Ground Structure) resonator and has designed the band -pass filter using the proposed ${\subset}$ stub-I type DGS resonator. This structure has strong advantages that can vary the retune loss at the passband freely and also can easily tune the attenuation pole frequency at the stopband. The bandpass filter can be made more smaller than the existing filters and be used to find the various applications for eliminating the harmonics and spurious mode at IMT-2000 band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.5
• /
• pp.544-552
• /
• 2010

In this paper, a new method to enhance the stop bandwidth of the compact microstrip bandstop filter based on split ring resonator(SRR) was proposed. To achieve wide stop bandwidth, we incorporated the SRR within the circular etched pattern of the defected ground structure(DGS). By incorporating the SRR within the circular etched pattern, a high magnetic coupling between SRR and signal line can be achieved. The high magnetic coupling enables the proposed structure to achieve a wide stop bandwidth. To verify the feasibility of the proposed structure, the proposed bandstop filter was compared with conventional bandstop filter employing SRRs which have been etched at both sides of the signal line. Simulation and experimental results show that the proposed structure provides an enhanced stop bandwidth compared with the conventional structure.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.6
• /
• pp.691-699
• /
• 2012

In this paper, we present a Vt-DRO with a low phase noise, which is achieved by improving the coupling structure between the dielectric resonator and microstrip line. The Vt-DRO is a closed-loop type and is composed of 3 blocks; dielectric resonator, phase shifter, and amplifier. We propose a mathematical estimation method of phase noise, using the group delay of the resonator. By modifying the coupling structure between the dielectric resonator and microstrip line, we achieved a group delay of 53 nsec. For convenience of measurement, wafer probes were inserted at each stage to measure the S-parameters of each block. The measured S-parameter of the Vt-DRO satisfies the open-loop oscillation condition. The Vt-DRO was implemented by connecting the input and output of the designed open-loop to form a closed-loop. As a result, the phase noise of the Vt-DRO was measured as -132.7 dBc/Hz(@ 100 kHz offset frequency), which approximates the predicted result at the center frequency of 5.3 GHz. The tuning-range of the Vt-DRO is about 5 MHz for tuning voltage of 0~10 V and the power is 4.5 dBm. PFTN-FOM is -31 dBm.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.449-455
• /
• 2018

For the size reduction, we propose a microstrip-fed monopole antenna with half X-slot in the radiation patch and cover WLAN dual band 2.4 GHz band (2.4 ~ 2.484 GHz) and 5 GHz band (5.15 ~ 5.825 GHz). The frequency characteristics such as impedance bandwidth and resonant frequencies were satisfied by optimizing the numerical values of various parameters, while the reflection loss in 5 GHz was improved by using defected ground structure (DGS). The proposed antenna is designed and fabricated on a FR-4 substrate with dielectric constant 4.3, thickness of 1.6 mm, and size of $24{\times}41mm^2$. The measured impedance bandwidths (${\mid}S_{11}{\mid}{\leq}-10dB$) of fabricated antenna are 450 MHz (2.27 ~ 2.72 GHz) in 2.4 GHz band and 1340 MHz (4.79 ~ 6.13 GHz) in 5 GHz band which sufficiently satisfied with the IEEE 802. 11n standard in dual band. In particular, radiation patterns which are stable as well as relatively omni-direction could be obtained, and the gain of antennas in each band was 1.31 and 1.98 dBi respectively.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.39 no.11
• /
• pp.34-39
• /
• 2002

In this paper, we proposed novel photonic bandgap(PBG) structure using EGP(Elevated Ground Plane) and via in ceramic substrate of microstrip line. From analysis result, the proposed PBG structure is reduced 52.5% at size and increased 45 % at bandwidth compared to typical planar PBG structure. It is also reduced 32 % at size and improved more than 8 dB at power loss compared to typical multilayer DGS(Defected Ground Structure). The proposed PBG structure also can be used bandstop and lowpass filter and it will be useful for small microwave integrated circuit and module development.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.1-9
• /
• 2014

In this paper, a reconfigurable polarization patch antenna that uses a Y-shaped feed is proposed. The proposed antenna consists of a square patch, a Y-shaped feeding structure, a PIN diode, and a bias circuit for diode operation. The structural symmetry/asymmetry of the feeding structure is determined by the on/off operation of the PIN diode that inserted into the side of one of the lines of the Y-shaped feeding structure. For the proposed reconfigurable antenna, the two microstrip lines of the feeding structure have the same length when the PIN diode operates in the on state, and the antenna exhibits linear polarization(LP). On the other hand, when the PIN diode operates in the off state, the length of one side line of the feeding structure is relatively shorter than that of the other line. Therefore, the antenna exhibits circular polarization(CP). From the measurement results, it is found that the proposed antenna exhibits good impedance matching and axial ratio. In addition, polarization switching can be easily achieved in the same operating band.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.7
• /
• pp.1182-1190
• /
• 2001

In this paper, microstrip photonic bandgap (PBG) structure with special perforation patterns etched on the line itself is analyzed and optimized in shape, then used for harmonic tuning of power amplifier. This PBG has an advantage in being fabricated and grounded. The dimension of unit lattice is enlarged vertically, but its input and output line maintain 50 Ω using tapered line. This modification from original structure can lessen possible error in etching PCB. The analysis and design of PBG structure are acquired from using EM simulation. The measured insertion loss of the final structure is 0.3 ∼0.4 dB, and its bandwidth of stopband is 6∼7 GHz. Measured results of improved characteristics by using PBG structure at the output of the power amplifier are 0.72∼0.99 dB in output power, 1.14∼7.8 % in PAE, and 1 dBc in the third IMD.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.4B
• /
• pp.388-396
• /
• 2002

In this paper, An aperture-coupled microstrip patch antenna operating at WLL frequency range(Rx : 2.3∼2.33Ghz, Tx : 2.37 ∼2.4Ghz) for WLL repeater is designed and fabricated. FR-4 epoxy substrate with 4.7 relative permittivity is inserted between feed-line and patch plane. Aperture-coupled structure is employed for consideration of bandwidth improvement and gain\`s characteristics. Air gap is arranged at each layer for bandwidth extension and radome is used as a protector in the upper patch. In this paper, both 1 port and 2 port are designed as 1$\times$2 array antenna which uses T-junction and λ$\_$g//4 transformer. Here, 1 port is used as transmitting/receiving antenna and 2 port is used as receiving antenna. Functionally independent two antennas using space diversity arrange slots between two antennas in order to be placed at the same place. As a result, we obtained a excellent isolation below -40dB and return loss is reduced by means of slots arrangement between patch and antenna.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.8
• /
• pp.67-78
• /
• 2009

Radiation characteristics of microstrip patch antennas integrated with mushroom-like EBG structures in all directions and length direction on a substrate with the relative dielectric constant of 10 are systematically analyzed. As the substrate thickness increases, the effect of the surface wave on the input impedance and radiation pattern of a patch antenna increases. The effect of EBG structures on the input impedance of a patch antenna is negligible when the distances between EBG structures and the center of a patch antenna are 0.4 ${\gamma}_0$, 0.2 ${\gamma}_0$ and 0.1 ${\gamma}_0$ for the substrate thickness of 3.2 mm, 1.6 mm and 0.8 mm, respectively. The forward radiation is improved due to the suppression of surface wave when the periods of EBG structures integrated are larger than 2, 2, 3 periods for the substrate thickness of 3.2 mm, 1.6 mm and 0.8 mm, respectively. The effects of EBG structures on the radiation characteristics of a patch antenna integrated with EBG structures in all directions and length direction are similar.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.4
• /
• pp.185-190
• /
• 2015

In this paper we characterized and designed the waveguide antipodal finline transition at 57-65GHz frequency band in V-band for 5G mobile communication systems. Especially, we proposed the design method of spline taper for finline tapers by means of increasing curvature from linear taper. We could perform optimization more effectively by excluding improper regions for optimal performance from optimization using the method. Return losses and insertion losses of antipodal finline transitions were mainly affected by the taper shape of the finline. The resonances in the structure of the finline transition were the strongest enemies who deteriorate the performance of the transition. And we alleviated the resonances using semicircle shaped patch. The designed antipodal finline transition showed good performance as it showed less than -24.2dB of return loss and -0.24dB of insertion loss in the band(57-65GHz) which we suppose to use.