• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.2
• /
• pp.260-267
• /
• 2014

In this paper, the unit cell of LH structure using microstrip transmission line and chip capacitor is devised, and the reactive components of equivalent circuit are extracted from the proposed unit cell. And then, we have analyzed for the unit cell parameters and applied the characteristics to the wideband high pass filter design. This filter cascading several unit cells with high pass property has been implemented on microstrip transmission line, and the performance has been the band rejection characteristics of 62.9 dB in the stop band to 0~2.18 GHz and less than the insertion loss of 1.17 dB in the pass band from 3.0G Hz to 12.75 GHz.

• Journal of information and communication convergence engineering
• /
• v.9 no.2
• /
• pp.150-154
• /
• 2011

In this paper a four-pole elliptic function bandpass filter is designed with two ground slots. A research of microstrip bandpass filters (BPF) using defected ground structures (DGS) is presented. DGS technique allows designs of tight couplings without the necessity of using very narrow coupling gaps. The simulator Sonnet is used to design the resonator and to calculate the coupling coefficient of the basic coupling structure. Compared to similar microstrip filters without defected ground structure, the simulated performances of these novel structures indicate some technological advantages.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.10
• /
• pp.24-28
• /
• 1992

A new design method of microstrip wide band VHF tunable bandpass filters using varacter diodes is presented. In the proposed filter both the input and output ports are coupled through capacitors, and an open micro-strip line is inserted between the coupled line in order to obtain the desired degree of coupling. The optimized filter responseses for the frequency range of 220-404MHz by TOUCH-STONE are compared with the measured ones.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.6A
• /
• pp.648-656
• /
• 2007

This paper is about band pass filter, using Ceramics in the condition of center frequency 370Hz at milli-wave. The band pass filter is applied to Broadband Convergence Network, representing WLL(Wireless Local Loop) and LMDS(Local Multi-point Distribution Service). Sticking ceramic between strip line on a dielectric material substrate with which conductor's covers upper and basal surface, One will house the exterior by using structural resonance. In this Non Radiative Microstrip Line Filter structure, based upon simulations, generalized the two formulas finding resonant frequency of 1step ceramic resonator and bandwidth of 4step ceramic resonator. Also, As a result of experiment, using Network Analyzer, about created a experiment of structure based on the simulation result of 4-step ceramic resonator, It showed good characteristic of targeted bandwidth, comparing simulated result of 36.58GHz$\sim$37.650GHz with experimented result of 36.6GHz$\sim$37.65GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.40 no.3
• /
• pp.18-24
• /
• 2003

The resonator using two layer microstrip structure was proposed and the bandpass filter was designed using this resonator in this paper. The proposed resonator structure is constructed by placing a U-shape of resonator in the first layer and then placing a broadside coupling strip in the second layer just above of the U-shape of resonator's edge part. Because these structure has various design parameters than general single layer coupled line structure, filter design is more flexible. In this paper, the narrow band filter was designed using multi-layer structure that had been applied to broadband filter because it's high coupling nature. The filter was designed to have 4MHz center frequency and 3 % fractional bandwidth, and finally confirmed that can be realizable narrow band filter by using multi-layer structure through fabrication and measurement.

• Progress in Superconductivity
• /
• v.2 no.2
• /
• pp.92-96
• /
• 2001

We have fabricated a modified hairpin-type YBa$_2$Cu$_3$O$_{7-{\delta}}$ (YBCO) 2-pole microstrip bandpass filter with the center frequency of 5.8 GHz. We designed a hairpin-type filter with interdigital-coupled inner poles to improve the filter performance. Compared to a typical hairpin-type filter of the same size, the center frequency, the bandwidth and the insertion loss appeared smaller by 14.5% ,29.6%, and 0.55 dB, respectively. The dimensions of the filter were 13.7mm ${\times}$3.3 mm. YBCO films deposited on r-cut sapphire buffered with a CeO$_2$thin layer were used fur making the filter.

• ETRI Journal
• /
• v.19 no.2
• /
• pp.48-58
• /
• 1997

Using high quality high-$T_c$ superconducting (HTS) YBCO thin films, we designed and fabricated 3-pole, 5-pole, and 7-pole lowpass filters consisting of microstrip transmission lines and open-stub lines. We measured the microwave response of the filters in the temperature range of T=85 K to 27 K. AtT=30 K, the observed inband insertion loss was 0.14dB and 0.02dB for the 5-pole and 7-pole filters, respectively. The cut-off frequency was 4.7 GHz for the 5-pole filter and 7.9GHz for the 7-pole filter. To the authors' knowledge, the measured inband insertion losses are the best values reported so far for the open-stub line type HTS multipole lowpass filters. The skirt property of the 5-pole filter showed a large improvement over that of the 3-pole filter as predicted from the simulation. We found that, to obtain a stable performance, the HTS multipole lowpass filters should be operated at the temperatures between 60% and 70% of $T_c$.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.3 no.2 s.5
• /
• pp.85-93
• /
• 2004

In this paper, microstrip stepped-impedance hairpin resonator (SIR) lowpass filter f.PF) by surface rnicromachining on GaAs substrate is sugsested. This filter has the advantages of compact side, easy fabrication, and sharp cutoff frequency response. The new SIR LPF shows the 3 dB passband of dc to 33 GHz, the insertion loss of 0.82 dB, and the return loss of better than 17 dB up to 25.57 GHz. This filter is useful for many microwave system applications.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.4
• /
• pp.585-590
• /
• 1993

A wide passband filter consisting of 3-stage ssymmetrical coupler can be realized, where the admittance inverter parameters in equivalent circuit of asymmetrical coupled microstrip lines are given as a function of a fundamental design parameter of a bandpass filter. An experimental filter was designed over 22 percend bandwidth centered at 9GHz and optimized using Super-Compact. Measured forward transmission and forward reflection closely matched design data but measured insertion loss was slightly higher (0.7dB) than the designed value.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.7
• /
• pp.395-400
• /
• 2004

In this paper, the four-pole elliptic function microstrip filter at 2.4GHz band with fractional bandwidth of 4% is realized using compact miniaturized hairpin resonators. The parallel algorithm FDTD method is used to analyze S-parameter of hairpin resonator filter more accurately, and to calculate the electric coupling and magnetic coupling among the hairpin resonators. Absorbing boundary conditions for mesh termination used Sulivan's simplified PML and the FDTD code was paralleled by MPI for IBM SP2 which had enhanced calculation speed. The experimental measurements are performed by HP8720D vector network analyzer. Measured results on fabricated hairpin type cross coupled bandpass filters show good agreements with theoretic results.