• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1819-1824
• /
• 2006

A microlens arrays formed by thermal reflow method is attached to an OLED device and the light extraction efficiency which includes luminance and power information is determined by adjusting the area ratio and the height ratio.

• Korean Journal of Optics and Photonics
• /
• v.5 no.3
• /
• pp.364-371
• /
• 1994

Real-time MTF measuring system for testing microlens arrays with a linear CCD array is developed. The spread function of slit image that is relayed and magnified by a microscopic object lens can be measured at several times in a second. The signal uniformity and MTF of CCD is also calibrated. The experimental result of micro lens arrays developed for contact image sensor is presented.sented.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2009.10a
• /
• pp.620-622
• /
• 2009

We demonstrated a liquid crystal display (LCD) mode with a single polarizer based on the array of a switchable microlens consisting of a circular stop mask and its complementary open mask. The focused beam passed through the open mask and thus the bright state was obtained, while the defocused beam was blocked by the stop mask and the complementary open mask. It is expected that our single-polarizer LCD mode is applicable to low cost displays.

• Journal of Information Display
• /
• v.13 no.4
• /
• pp.139-143
• /
• 2012

In this study, optical simulation was used to compare three optical structures that could be applied to the typical organic light-emitting diode to increase the outcoupling efficiency. These were spherical scattering particles (treated as Mie scatterers) embedded in the glass substrate, microlenses formed on the glass substrate, and a diffusing layer (DL) with a Gaussian scattering distribution function inserted between the indium tin oxide (ITO) and the glass substrate. It was found that the application of microlens array and that of scattering particles in the glass substrate exhibited similar enhancements in the outcoupling efficiency when the density and the refractive index of the scattering particles were optimized. The DL located at the interface between the glass and the ITO further enhanced the efficiency because it could further extract the trapped light in the waveguide mode. The appropriate combination of these three structures increased the outcoupling efficiency to about 42%, which is much greater than the typical values of 15-20% when there is no optical structure for light extraction.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.11
• /
• pp.857-861
• /
• 2012

FPN (fixed-pattern-noise) mainly comes from the device or pattern mismatches in pixel and color filter, pixel photodiode leakage in CMOS image sensor. In this paper, optical stack module related pixel FPN was investigated and the classification of pixel FPN contribution with the individual optical module process was presented. The methodology and procedure would be helpful in reducing the greater pixel FPN and distinguishing the complex FPN sources with respect to various noise factors.

• Medical Lasers
• /
• v.9 no.2
• /
• pp.179-183
• /
• 2020

The picosecond laser has been widely used to remove tattoos, and improve wrinkles, acne scarring, and pigmented scars. This study was performed to investigate the efficacy and safety of a 1,064-nm fractional picosecond laser treatment for depressed traumatic scars. A total of twenty Korean patients with depressed scars were treated with a 1,064-nm fractional picosecond laser at a two-week interval with a spot size of 3 mm, fluence of 3.5 to 5.5 J/cm², and frequency of 2 Hz with a combination of microlens arrays. At 4 weeks after the final treatment, there was a statistically significant improvement in the modified Vancouver Scar Scale (mVSS) and the patient satisfaction score without any significant complication. A 1,064-nm fractional picosecond laser treatment is a safe and effective method to improve traumatic wound scars with depression.

• Korean Journal of Optics and Photonics
• /
• v.23 no.3
• /
• pp.119-123
• /
• 2012

The structure of an LCD backlight unit (BLU) was simplified by installing a micro reverse-pyramid array (MRPA) or a micro reverse-cone array (MRCA) on the top surface of the light guide panel (LGP) in order to eliminate the conventional diffuser sheet and the prism sheet. The optimum conditions of the MRPA and the MRCA in the new light guide panel were obtained through optical simulation. The change of the luminance and view angle that depend on the side angle, the height, and the length at the top of the MRPA and MRCA were studied. The optimized side angle and the view angle of the MRPA and MRCA were 59 and 57 degrees for the side angles and 68 and 64 degrees for the view angles, respectively.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.2
• /
• pp.123-130
• /
• 2008

A 3D structure production method for microstereolithography is a useful way that produces complex structures with flexible processes and low cost. Several UV curable resins were blended and the optimal resin for micro-lens fabricate was selected through viscosity, workability and transmission tests. It consists of 1, 6 - Hexanediol diacrylate with 15 Apha and Isobornyl acrylate for reducing some shrinkage. When fabricating a micro-lens array on large surface, some distortion of shape occurred because of the surface tension between cured part. To overcome this problem, the optimal processing conditions were derived from considering amount of the resin and surface tension. Large surface Micro-lens array, which are a type of elliptical convex and consist of 18,000 micro-lens in the range of 2cm*2cm were fabricated. The focal length to the X-axis and Y-axis were calculated. To verify the performance, measure an energy distribution of transmitted light from the Large surface Micro-lens array.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1591-1594
• /
• 2006

In this work, we fabricated efficient white organic light emitting device (WOLED) by the stack of complementary fluorescent dye-doped layers, Effect of dye-doping ratio and thickness of each layers on WOLED efficiency and emission spectrum was investigated. Moreover, out-coupling efficiency enhancement using microlens array was analyzed for bottom and top-emitting device architecture, leading to higher light extraction properties.

• Proceedings of the Optical Society of Korea Conference
• /
• 2000.02a
• /
• pp.190-191
• /
• 2000

미세가공 기술을 이용한 초소형 렌즈의 제작 및 연구가 매우 활발히 진행되고 있다. 초소형렌즈의 응용 분야는 바코더 스캐너, 레이저 프린터, 프로젝터, 광 기록 장치, 광섬유를 이용한 광통신 등이 있으며 앞으로도 더 많은 응용 분야를 위한 광범위한 설계와 제작 공정들이 연구되어 갈 것이다. 본 논문에서는 아크릴 레진을 이용하여 초소형 렌즈를 제작하는 공정을 개발하여 새로운 재료와 공정에 대한 가능성을 확인한다. (중략)