• Applied Chemistry for Engineering
• /
• v.17 no.2
• /
• pp.125-131
• /
• 2006

Dimethyl ether (DME) is a new clean fuel as an environmentally-benign energy resource. DME can be manufactured from various energy sources including natural gas, coal, biomass and spent plastic. In addition to its environmentally friendly properties, DME has similar characteristics to those of LPG. Therefore, it is considered as an excellent substitute fuel for LPG, fuel cells, power plant, and especially diesel and is expected to be the alternative fuel by 2010. The experimental study of the direct synthesis of DME was investigated under various conditions over a temperature range of $220{\sim}280^{\circ}C$, syngas ratio 1.2~3.0. All experiments were carried out with a hybrid catalyst, composed of a methanol synthesis catalyst ($Cu/ZnO/Al_2O_3$) and a dehydration catalyst (${\gamma}-Al_2O_3$). The observed reaction rate follows qualitatively a Langmiur-Hinshellwood model as the reaction mechanism. Such a mechanism is considered with three reactions; methanol synthesis, methanol dehydration and water gas shift reaction. From a surface reaction with dissociative adsorption of hydrogen, methanol, and water, individual reaction rate was determined.

• Korean Journal of Materials Research
• /
• v.20 no.5
• /
• pp.267-270
• /
• 2010

Sn doped $In_2O_3$ (ITO) and ITO/Cu/ITO (ICI) multilayer films were prepared on glass substrates with a reactive radio frequency (RF) magnetron sputter without intentional substrate heating, and then the influence of the Cu interlayer on the methanol gas sensitivity of the ICI films were considered. Although both ITO and ICI film sensors had the same thickness of 100 nm, the ICI sensors had a sandwich structure of ITO 50 nm/Cu 5 nm/ITO 45 nm. The ICI films showed a ten times higher carrier density than that of the pure ITO films. However, the Cu interlayer may also have caused the decrement of carrier mobility because the interfaces between the ITO and Cu interlayer acted as a barrier to carrier movement. Although the ICI films had two times a lower mobility than that of the pure ITO films, the ICI films had a higher conductivity of $3.6{\cdot}10^{-4}\;{\Omega}cm$ due to a higher carrier density. The changes in the sensitivity of the film sensors caused by methanol gas ranging from 50 to 500 ppm were measured at room temperature. The ICI sensors showed a higher gas sensitivity than that of the ITO single layer sensors. Finally, it can be concluded that the ICI film sensors have the potential to be used as improved methanol gas sensors.

• KSBB Journal
• /
• v.11 no.6
• /
• pp.642-648
• /
• 1996

The effects of EDTA(Ethylene diamine tetraacetic acid), Cu, temperature, and gas(methane and oxygen) composition on methanol production from methane with Methylosinus trichosporium were investigated. In this experiment EDTA was found to be a potential methanol dehydrogenase inhibitor since it causes methanol accumulation and 6mM was found to be optimum concentration of EDTA for methanol production. When Cu was added in culture media, the produced methanol concentration level was increased. Hence it is believed that Cu enhanced the particulate methane monooxygenase formation and consequently the addition of Cu could increase the methanol production from methane. In this experiment the optimum concentration of Cu was found to be 1mM for methanol production. When temperature was shifted down from $30^{\circ}C to 25^{\circ}C$, the methanol production level was enhanced by 50%. When the ratio of methane to oxygen in gas phase was increased to 2.3 from 1, produced methanol concentration was also enhanced by 100%.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1503-1505
• /
• 1998

Stearic acid was deposited on surface of 9[MHz], AT-cut quartz crystal microbalance as gas sensing material using Langmuir-Blodgett(LB) technique. We measured gas response between deposited LB films and organic gas for various temperature($0{\sim}80^{\circ}C$). The resonant frequency changed due to absorbance of organic gas such as methanol and butanol gas at room temperature. However, the resonant frequency not responded to methanol gas at temperature above melting point of deposited LB films.

• Journal of Sensor Science and Technology
• /
• v.15 no.3
• /
• pp.205-210
• /
• 2006

Hydrophobic polymer [ex. Poly(vinylidenfluoride)] layer was coated on polyaniline (PANi) sensor to reduce the contamination humidity. The differences in sensitivity to methanol gas detection in various humidity condition between pure-PANi sensor and sensor coated with poly(vinylidenfluoride) polymer (PVDF) (coated-PANi sensor) were investigated. Considering the relation between the density of pore, which was coated on the layer of the PANi sensor, and sensitivity was investigated. To fabricate the porous PVDF layer on PANi sensor, poly(vinylalcohol) (PVA), which is water-soluble polymer, was used. Coated-PANi sensor was less affected by humidity compared with pure-PANi sensor. And higher density of pore on PVDF layer led to higher sensitivity.

• Journal of the korean Society of Automotive Engineers
• /
• v.13 no.5
• /
• pp.81-88
• /
• 1991

Combustion characteristic, concentration of NOx and exhaust smoke opacity was experimentally tested, according to fuel injection timing, mixing ratio of water and methanol for the driving condition of 2000 rpm of engine revolution and constant load(7.5kg/cm$^{2}$) using emulsified fuel of gas oil-water methanol. The result obtained was as following. Thermal efficiency indicated highly 0.4-2.7% for emulsified fuel then gas oil, and injection timing when maximum thermal efficiency, slicily risen then gas oil. For constant fuel injection timing ignition lag was increased, combustion duration decreased, maximum heat release rate indicated high, and concentration of NOx and exhaust smoke opacity is decreased, as function of water and methanol content y was higher.

• Journal of the Korean Vacuum Society
• /
• v.20 no.3
• /
• pp.195-199
• /
• 2011

ITO thin films and gold (Au), copper (Cu) and nickel (Ni) intermediate ITO multilayer (ITO/Au/ITO, ITO/Cu/ITO, ITO/Ni/ITO) films were deposited on glass substrates with a reactive radio frequency and direct current magnetron sputtering system and then the effect of intermediate metal layer and annealing temperature on the methanol gas sensitivity of ITO films were investigated. Although both ITO and ITO/metal/ITO (IMI) film sensors have the same total thickness of 100 nm, IMI sensors have a sandwich structure of ITO 50 nm/metal 10 nm/ITO 40 nm. The change in the gas sensitivity of the film sensors caused by methanol gas ranging from 100 to 1000 ppm was measured at room temperature. The IAI film sensors showed the higher sensitivity than the other sensors. Finally, it is concluded that the ITO 50/Au 10/ITO 40 nm film sensors hasthe potential to be used as improved methanol gas sensor.

• 한국가스학회:학술대회논문집
• /
• 2005.10a
• /
• pp.141-145
• /
• 2005

DME (Di-Methyl Ether) is a new clean fuel and an environmental-friendly energy resource, also is recently increasing with an alternative interest because of the industrial use. DME has been shown to have excellent properties as a diesel fuel giving emission level better than ULEV standard. So it has been attracting considerable as an alternative diesel fuel. In this study, we carried out simulation of separation and purification process of demo plant for 101on per day DME production, which cause the effect that is important in productivity, from operation results of pilot plant for 50kg per day DME production. The liquefied stream, which was separated by gas-liquid separator after DME reactor, includes $CO_2$, DME, Methanol and $H_2O$. We established three distillation columns for separation and purification of the stream. $CO_2$ was extracted from the stream by first distillation column, DME was extracted by second column and Methanol was extracted by third column. We investigated and analyzed the effect which the actual operation variables cause in efficiency of process and optimized process, finally we got the DME of purity $100\%$.

• Clean Technology
• /
• v.6 no.2
• /
• pp.129-137
• /
• 2000

A methanol synthesis process via reverse-water-gas-shift and methanol formation reactions has been analyzed using the notion of exergy. The analysis has been based on the simulation results with the aid of real operating data. Driving and material exergy losses have been defined and quantified, respectively. Locations and the reason of major exergy losses have been pinpointed and improvement strategies have been suggested. It had been noted that the exergy analysis can provide a sound scientific base for adopting the concept of industrial ecology and developing loss prevention schemes.

• Mass Spectrometry Letters
• /
• v.14 no.3
• /
• pp.79-90
• /
• 2023

Natural goods, especially therapeutic plants, are abundant in the World. Because they have the ability to provide all humanity with countless advantages as a source of medicines, medicinal plants are presently receiving more attention than ever. These plants' therapeutic efficacy is based on bioactive phytochemical components that have clear physiological effects on the human body. The drying process is crucial for the preparation of plant materials prior to extraction since freshly harvested plant materials include active enzymes that create active components, intermediates, and metabolic processes. Many of the phytoconstituents may be extracted using the semi-polar solvent methanol. The goal of the current work is to use the GC-MS gas chromatography- mass spectrometry technology to identify the phytochemicals and review their biological activity. In methanol leaf extract, 5 phytocompounds were found in Ricinus communis, 5 phytocompounds in Pongamia pinnata, 12 phytocompounds in Datura metal, 7 phytocompounds in Azadirachta indica, 11 phytocompounds in Acalypha indica.