• Composites Research
• /
• v.17 no.2
• /
• pp.34-39
• /
• 2004

In this paper, a modified and representative unit cell model was employed to study the tensile behaviour of closed-cell metallic foams with varying spatial density distribution as well as material imperfections. The density variation was assumed to follow a statistical probability distribution of the Gaussian type. A multiple cell finite element model, utilising the modified unit cell, was developed. The model exhibits deformation patterns similar to those observed in tensile testing. The nominal stress-strain curve obtained from quasistatic tensile of the foam was compared with experimental findings and was found to be in good agreement in the scheme of maximum strength only if the appropriate density distribution and volume fraction of internal imperfections are taken into account. Moreover, maximum tensile strength of the aluminium foam was found to be more sensitive to the volume fraction of imperfection than standard deviation of the density.

• Structural Engineering and Mechanics
• /
• v.74 no.1
• /
• pp.19-32
• /
• 2020

Metallic energy-dissipation dampers are widely used in structures. They are comprised of an added damping and stiffness (ADAS) device with many parallel, diamond-shaped hole plates, the neck width of which is an important parameter. However, no studies have analyzed the neck width's influence on the ADAS device's performance. This study aims to better understand that influence by conducting a pseudo-static test on ADAS, with three different neck widths, and performing finite element analysis (FEA) models. Based on the FEA results and mechanical theory, a design neck width range was proposed. The results showed that when the neck width was within the specified range, the diamond-shaped hole plate achieved an ideal yield state with minimal stress concentration, where the ADAS had an optimal energy dissipation performance and the brittle shear fracture on the neck was avoided. The theoretical values of the ADAS yield loads were in good agreement with the test values. While the theoretical value of the elastic stiffness was lower than the test value, the discrepancy could be reduced with the proposed modified coefficient.

• Earthquakes and Structures
• /
• v.8 no.4
• /
• pp.821-841
• /
• 2015

This paper proposes a two-stage imaging approach for quantitative inspection of damages in metallic plates using the fundamental anti-symmetric mode of ($A_0$) Lamb wave. The proposed approach employs a number of transducers to transmit and receive $A_0$ Lamb wave pulses, and hence, to sequentially scan the plate structures before and after the presence of damage. The approach is applied to image the corrosion damages, which are simplified as a reduction of plate thickness in this study. In stage-one of the proposed approach a damage location image is reconstructed by analyzing the cross-correlation of the wavelet coefficient calculated from the excitation pulse and scattered wave signals for each transducer pairs to determine the damage location. In stage-two the Lamb wave diffraction tomography is then used to reconstruct a thickness reduction image for evaluating the size and depth of the damage. Finite element simulations are carried out to provide a comprehensive verification of the proposed imaging approach. A number of numerical case studies considering a circular transducer network with eight transducers are used to identify the damages with different locations, sizes and thicknesses. The results show that the proposed methodology is able to accurately identify the damage locations with inaccuracy of the order of few millimeters of a circular inspection area of $100mm^2$ and provide a reasonable estimation of the size and depth of the damages.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.359-359
• /
• 2010

Self-organized nanostructures of dots, holes or ripples produced by energetic ion bombardment have been reported in a wide variety of substrates. Ion bombardment on an alloy or compound also draws much attention because it can induce a surface composition modulation with a topographical surface structure evolution. V. B. Shenoy et al. further suggested that, in the case of alloy surfaces, the differences in the sputtering yields and surface diffusivities of the alloy components will lead to a lateral surface composition modulation [1]. In the present work, the classical molecular dynamics simulation of Ar bombardment on metallic alloys at room temperature revealed that this bombardment induces a surface composition modulation in layer-by-layer mode. In both the $Co_{0.5}Cu_{0.5}$ alloy and the CoAl B2 phase, the element of higher-sputtering yield is accumulated on the top surface layer, whereas it is depleted in lower layers. A kinetic model considering both the rearrangement and the sputtering of the substrate atoms agrees with the puzzling simulation results, which revealed that the rearrangement of the substrate atoms plays a significant role in the observed composition modulation.

• Korean Journal of Metals and Materials
• /
• v.49 no.12
• /
• pp.930-936
• /
• 2011

In the present study, we show that the addition of Ag, an element having a positive enthalpy of mixing with Cu in the liquid state, enables the simultaneous enhancement of the glass forming ability and the plasticity in Cu-Zr-Ag bulk metallic glasses (BMGs). Rods of 4 mm diameter could be prepared with a fully amorphous structure and values of plastic strain up to 18% were measured under a compression mode for compositions around $Cu_{42.5}Zr_{47.5}Ag_{10}$. The possible role of Ag in the change of the atomic structure and the enhancement of the plastic strain in the ternary Cu-Zr-Ag BMGs is discussed based on analyses from transmission electron microscopy and EXAFS (extended X-ray absorption fine structure).

• Steel and Composite Structures
• /
• v.45 no.5
• /
• pp.683-695
• /
• 2022

Conventional braces are often used to provide stiffness to structures; however due to buckling they cannot be used as seismic energy dissipating elements. In this study, a seismic energy dissipation device is proposed which is comprised of a bracing member and a steel hysteretic damper made of steel hexagonal plates. The hexagonal shaped designated fuse causes formation of plastic hinges under axial deformation of the brace. The main advantages of this damper compared to conventional metallic dampers and buckling-restrained braces are the stable and controlled energy dissipation capability with ease of manufacture. The mechanical behavior of the damper is formulated first and a design procedure is provided. Next, the theoretical formulation and the efficiency of the damper are verified using finite element (FE) analyses. An analytical model of the damper is established and its efficiency is further investigated by applying it to seismic retrofit of a case study structure. The seismic performance of the structure is evaluated before and after retrofit in terms of maximum interstory drift ratio, top story displacement, residual displacement, and energy dissipation of dampers. Overall, the median of maximum interstory drift ratios is reduced from 3.8% to 1.6% and the residual displacement decreased in the x-direction which corresponds to the predominant mode shape of the structure. The analysis results show that the developed damper can provide cost-effective seismic protection of structures.

• Steel and Composite Structures
• /
• v.45 no.3
• /
• pp.455-466
• /
• 2022

Despite the considerable lateral stiffness and strength of the Concentrically Braced Frame (CBF), it suffers from low ductility and low seismic dissipating energy capacity. The buckling of the diagonal members of the CBF systems under cyclic loading ended up to the shortcoming against seismic loading. Comprehensive researches have been performing to achieve helpful approaches to prevent the buckling of the diagonal member. Among the recommended ideas, metallic damper revealed a better success than other ideas to enhance the behavior of CBFs. While metallic dampers improve the behavior of the CBF system, they increase constructional costs. Therefore, in this paper, a new steel damper with flexural mechanism is proposed, which is investigated experimentally and numerically. Also, a parametrical revision was carried out to evaluate the effect of thickness, slenderness ratio, angle of the main plate, and height of the main plates on the proposed damper. For the parametrical study, 45 finite element models were analyzed and considered. Experimental results, as well as the numerical results, indicated that the proposed damper enjoys a stable hysteresis loop without any degradation up to a high rotation equal to around 31% that is significantly considerable. Moreover, it showed a suitable performance in case of ductility and energy dissipating. Besides, the necessary formulas to design the damper, the required relations were proposed to design the elements outside the damper to ensure the damper acts as a ductile fuse.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.1
• /
• pp.198-204
• /
• 2001

The shot peening is largely used for a surface treatment of metallic components where small spherical pellets called shots are blasted onto the surface with velocities up to 100 m/s. This treatment leads to improvement of fatigue behavior due to the developed compressive residual stresses, and so it has gained widespread acceptance I the automobile and aerospace industries. The residual stress profile on surface layer depends on the parameters of shot peening, which are, shot velocity, shot diameter, coverage, impact angle, material properties etc. and the method to confirm this profile is the measurement by X-ray diffractometer only. Despite the importance to automobile ad aerospace industries, little attention has been devoted to the accurate modelling of the process. In this paper, the simulation technique is applied to predict the magnitude ad distribution of the residual stress and plastic deformation caused by shot peening with the help of the finite element analysis.

• Journal of the Korean Society for Heat Treatment
• /
• v.8 no.3
• /
• pp.213-221
• /
• 1995

Temperature distribution, transformation and residual stresses generated during the quenching process of carbon steel. It follows many difficulties in the analytical considerations on those quenching process because of the coupling effects on temperature and metallic structures. In this paper one of the basic study on the quenching stresses was carried out for the case of the round steel bar specimen(SM45C) with 40mm both in its diameter and length. The temperature distributions considering strain hysteresis were numerically calculated by finite element technique. In calculating the transient temperature field, the heat flux between water and rod surface was determined from the heat transfer coefficient. The gradient of temperature is almost same to geometric of specimen. At early stage of the quenching process, the abrupt temperature gradient has been shown in the surface of the specimen.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.712-720
• /
• 2003

In this paper, a multi-layered metallic disk array structure(MDAS) excited by cross-dipole elements was proposed for efficiently shaping of flat-topped element patterns(FTEP) with circular polarization. The MDAS excited by cross-dipole elements has advantages to decrease in volume and weight of an overall array antenna and so, it is appropriate for the FTEP applications of a ralativlely low frequency band. In order to verify the effectness of this structure, the MDAS breadboard operated at X-band(7.9 ∼ 8.4 GHz) was fabricated, and its design parameters were experimentally optimized on the basis of the previous design experience. The experimental results were shown that the MDAS could shape good FTEPs of ${\pm}$20$^{\circ}$beam width at least within a 6.1 % frequency band.