• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권6호
• /
• pp.360-366
• /
• 2000

This paper presents the fabrication and test of a micropump consisting of a pair of Al flap valves and a phase-change type actuator. The actuator is composed of a heater, a silicone rubber diaphragm and a working fluid chamber. The diaphragm is actuated by the vaporization and the condensation of the working fluid. The micropump is fabricated by the anisotropic etching, the boron diffusion and the metal evaporation. The forward and the backward flow characteristics of the flap valves illustrate the appropriateness as a check valve. Also, the flow rate of the micropump is measured. When the square wave input voltage of 8 V, 70% duty ratio and 2 Hz is applied to the heater, the maximum flow rate of the micropump is $97\muell/min$ for zero pressure difference.

• Journal of Mechanical Science and Technology
• /
• 제19권2호
• /
• pp.496-504
• /
• 2005

The thermal and mechanical properties of an electro-slag cast steel of a similar chemical composition with an AISI-6F2 steel are investigated and compared with a forged AISI-6F2 steel. AISI-6F2 is a hot-working tool steel. Electro-slag casting (ESC) is a method of producing ingots in a water-cooled metal mold by the heat generated in an electrically conductive slag when current passes through a consumable electrode. The ESC method provides the possibility of producing material for the high quality hot-working tools and ingots directly into a desirable shape. In the present study, the thermal and mechanical properties of yield strength, tensile strength, hardness, impact toughness, wear resistance, thermal fatigue resistance, and thermal shock resistance for electro-slag cast and forged steel are experimentally measured for both annealed and quenched and tempered heat treatment conditions. It has been found that the electro-slag cast steel has comparable thermal and mechanical properties to the forged steel.

• Safety and Health at Work
• /
• 제11권1호
• /
• pp.1-9
• /
• 2020

Background: As the impact of climate change intensifies, exposure to heat stress will grow, leading to a loss of work capacity for vulnerable occupations and affecting individual labor decisions. This study estimates the future work capacity under the Representative Concentration Pathways 8.5 scenario and discusses its regional impacts on the occupational structure in the Republic of Korea. Methods: The data utilized for this study constitute the local wet bulb globe temperature from the Korea Meteorological Administration and information from the Korean Working Condition Survey from the Occupational Safety and Health Research Institute of Korea. Using these data, we classify the occupations vulnerable to heat stress and estimate future changes in work capacity at the local scale, considering the occupational structure. We then identify the spatial cluster of diminishing work capacity using exploratory spatial data analysis. Results: Our findings indicate that 52 occupations are at risk of heat stress, including machine operators and elementary laborers working in the construction, welding, metal, and mining industries. Moreover, spatial clusters with diminished work capacity appear in southwest Korea. Conclusion: Although previous studies investigated the work capacity associated with heat stress in terms of climatic impact, this study quantifies the local impacts due to the global risk of climate change. The results suggest the need for mainstreaming an adaptation policy related to work capacity in regional development strategies.

• 한국표면공학회지
• /
• 제21권2호
• /
• pp.53-67
• /
• 1988

The high temperature corrosion of Fe-C alloys were studied at I atm SO gas in the temperature range 500~80$0^{\circ}C$ by means of a thermogravimetric analysis. The Na2SO4 induced high tempwrature corrosion rate was also measured at atm O2 gas under above the temperature renge. The reaction products were identified with the aid of X-ray diffraction technique, and micostruction of the alloy/scale interface was observed with a optical microscope and SEM. The experimental results were disussed by the themodeynamic calcutions. Under above the experimental condition. the reaction rates decrbon with increasing carbon content. The transfer of Fe ion was limited by a residue of carbon precipitated at alloy scale interface due to the oxidation of Fe-C alloys at alloy surface. The effect of cold working on reaction rate was different between the Fe containing low carbon and Fe-C Alloy containing carbon above 0,73 wt%. In a cold worked iron containing low carbon content, the crystallization of metal surface leads to the poor adherence between the alloy and the cavity formed between the alloy and scale. The outward diffusion of ion through the scale is estimated to be hindered by the cavity formed between the scale, consequently decreasing reaction rate. In the case Fe-C containing carbon above 0.73 Wt% alloy, the reaction rate was little affected by cold working, because the effect of content on reaction rats is greater than the effect of cold working.

• 보건교육건강증진학회지
• /
• 제18권2호
• /
• pp.141-156
• /
• 2001

This study was performed to identify the occupational diseases in the dental technicians working in Korea, and to elucidate the main related affecting factors for the occurrence of the occupational diseases. The research was carried out using a mail questionnaire and data collection was done for two months from April 15, 2000. The questionnaires were delivered to 1000 dental technicians working at 250 dental laboratories which were chosen among the total 1330 dental laboratories in south Korea. And 763 questionnaires were collected, then 739 questionnaires were used for a logistic and a multiple regression analyses. The results obtained in this study are summarized as follows: 1. The occupational diseases in the dental technicians included pneumoconiosis, chronic bronchitis, asthma, pneumonia, hyposmia, allergic dermatitis, eczema, contagious dermatitis, central nervous disorder, dysfunction of finger, vertebral disorder, dysfunction of interphalangeal joint, ophthalmitis, auditory dysfunction, otitismedia, optic trauma, and bum. 2. The main related affecting factors for the occurrence of the occupational diseases in the dental technicians were elucidated as follows: On the ccurrence of chronic bronchitis, vibration of equipment and job career were affected positively. On the ccurrence of asthma, job career and career on current working part were affected positively, but exhaust ventilation, work hour were affected negatively. On the occurrence of eczema, career on current working part and vibration of equipment were affected positively, but personal protective equipment, local exhaust ventilation, isolation of gas source were affected negatively. And eczema was occurred more in methyl methacrylate work than in any other work part. On the occurrence of finger dysfunction, vibration of equipment and noise of work place were affected positively. But personal protective equipment, local exhaust ventilation, isolation of dust and gas source were affected negatively. But finger dysfunction was occurred more in metal polishing than in any other work part. On the occurrence of auditory dysfunction, noise of work place were affected negatively. The results obtained in this study can give a valuable information for a prevention of the occupational diseases in the dental technicians working in Korea, and for keeping them in healthy. This study also can be helpful for a researcher who is aiming at a identification of occupational diseases and a elucidation of related affecting factors in a similar occupation.

• 생명과학회지
• /
• 제13권6호
• /
• pp.917-923
• /
• 2003

P. aeruginosa EMS1에 의한 수용성 절삭유의 생물학적 처리를 위한 환경요인과 최적조건을 검토한 결과는 다음과 같다. 절삭유속에 함유된 각종 성분을 이용한 P aeruginosa EMSl의 생육 및 절삭유 분해 가능성을 검토하기 위하여 증류수에 절삭유를 1% 농도로 첨가하여 멸균한 후, P aeruginosa EMSl를 접종하여 균체 생육도 및 COD 제거율을 조사한 결과, 균주의 생육도는 극히 미약하고 약 12%의 COD 제거능을 가지고 있었다. 이것은 균주의 생육과 효율적인 COD제거능을 위하여 절삭유 속에 함유된 성분 외의 다른 일반적인 배지성분이 필요함을 시사한다. P. aeruginosa EMS1에 의한 1% 수용성 절삭유의 COD 제거율과 균주 생육도 향상을 위한 최적 배지조성은 0.3% NH_4NO_3,\; 0.05%\; K_2HPO_4,\; 0.04% KH_2PO_4,\; 0.05%\; MgSO_4.7H_2O,\; 0.03%\; CaCl_2.2H_2O,\; 0.04%\; FeSO_4.7H_2O$이었고, 최적배양 조건은 pH 7,$30^{\circ}C$, 50m$\ell$ / 300m$\ell$flask이었다. 이 조건에서 배양 4일 후, 87%의 COD가 제거되었다. 최적배지에서 COD 제거에 미치는 절삭유 농도의 영향을 조사한 결과, 절삭유 농도가 낮을수록 relative COD(%)가 낮았으며, 균체 생육도가 높음을 알 수 있었다. 따라서 본 연구의 결과를 바탕으로 하여 현재 폐절삭유의 처리를 위해 시행되고 있는 물리화학적 처리 시스템의 후속 공정으로 생물학적 처리시스템을 구축하고, 표준 균주로서 P. aeruginesa EMS1이 사용될 경우, 잔여 절삭유의 완전 분해가 가능할 것으로 사료된다.

• 방사선산업학회지
• /
• 제18권1호
• /
• pp.43-52
• /
• 2024

Currently, there are no interim storage facilities and permanent disposal facilities in Korea, so all spent nuclear fuels are temporarily stored. However, the temporary storage facility is approaching saturation, and as a measure to this, the 2nd Basic Plan for the Management of High-Level Radioactive Waste presented an operation plan for dry interim storage facilities and dry temporary storage facilities on the NPP on-site. The dry storage can be operated in various ways, and to select the optimal dry storage method, the reduction of exposure for workers must be considered. Accordingly, it is necessary to develop a worker exposure scenario according to the dry storage method and evaluate and compare the radiological impact for each method. The purpose of this study is to develop an exposure scenario for workers transporting spent nuclear fuel by dry storage method. To this end, first, the operation procedure of the foreign commercial spent nuclear fuel dry storage system was analyzed based on the Final Safety Analysis Report (FSAR). 1) the concrete overpack-based system, 2) the metal overpack-based system, and 3) the vertical storage module-based system were selected for analysis. Factors were assumed that could affect the type of work (working distance, working hours, number of workers, etc.) during transportation work. Finally, the work type of the processes involved in transporting spent nuclear fuel by dry storage method was set, and an exposure scenario was developed accordingly. The concrete overpack method, the metal overpack method, and the vertical storage module method were classified into a total of 31, 9, and 23 processes, respectively. The work distance, work time, and number of workers for each process were set. The product of working hours and number of workers (Man-hour) was set high in the order of concrete overpack method, vertical storage module method, and metal overpack method, and short-range work (10 cm) was most often applied to the concrete overpack method. The results of this study are expected to be used as basic data for performing radiological comparisons of transport workers by dry storage method of spent nuclear fuel.

• 소성∙가공
• /
• 제7권5호
• /
• pp.489-495
• /
• 1998

Spinning is a chipless forming method for producing axially symmetric parts by using axial-radial motions of a spinning roller. This process has still some advantages in such a view point that a variety of complex shapes which can not be formed in a press can be easily spun at a low cost although it is one of the oldest forming methods for spinning mainly cookware parts for a long time. This study is to investigate the optimum roller path in order to obtain the maximum spinnability in producing cylindrical cups of Aluminum(A1050-H16) sheet metal. Working conditions applicable to any size of blank were predetermined through preliminary spinning tests. 9 types of roller path were proposed and experiments were carried out. The modified involute curve was shown to give the maximum drawing ration and more uniform quality of spun cups as compared with other results of this study. in addition thickness distribution and dimensional accuracy of spun cups were examined and discussed.

• 오토저널
• /
• 제7권3호
• /
• pp.42-55
• /
• 1985

The study is concerned with the investigation of curved line folding of developable surface from flat sheets of metal. General geometric relations among folding line, folded surface, folded angle are derived. From the derived geometric relations, the required plastic work and punch force are derived for the first approximation. Five methods of forming are suggested and the experiment is carried out using two chosen methods for the prismatic developable surfaces of which cross-sections have 103.deg.arc, 180.deg.arc, sinusoidal shape. In the die design for the tolding of prismatic developable surfaces, a stack of sheets were used to form shapes of the dies by which acceptable folded surfaces were obtained. The computed plastic work and punch force turned out to be in reasonable agreement with the experimental result.

• 전기전자학회논문지
• /
• 제15권2호
• /
• pp.143-148
• /
• 2011

MOS (Metal-Oxide Semconductor) devices among the most sensistive of all semiconductors to radiation, in particular ionizing radiation, showing much change even after a relatively low dose. The necessity of a radiation dosimeter robust enough for the working environment has increased in the fields of aerospace, radio-therapy, atomic power plant facilities, and other places where radiation exists. The power MOSFET (Metal-Oxide Semiconductor Field-Effect Transistor) has been tested for use as a gamma radiation dosimeter by measuring the variation of threshold voltage based on the quantity of dose, and a maximum total dose of 30 krad exposed to a $^{60}Co$ ${\gamma}$-radiation source, which is sensitive to environment parameters such as temperature. The gate oxide structures give the main influence on the changes in the electrical characteristics affected by irradiation. The variation of threshold voltage on the operating temperature has caused errors, and needs calibration. These effects can be overcome by adjusting gate oxide thickness and implanting impurity at the surface of well region in MOSFET.