• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.139-142
• /
• 2000

The SiCp/AC8A composites were fabricated by the pressureless metal infiltration process successfully. The effect of additional Mg, which were mixed with SiC particles to promote interfacial wetting between the reinforcement and matrix alloy, and particle size on the mechanical properties was investigated. By increasing the additional Mg content the hardness of SiCp/AC8A composites was increased due to the hard reaction products, but the bending strength was decreased by the excess reaction of Mg and high porosity level when the additional Mg content is over 7%. The Hardness and bending strength was increased by decreasing the size of SiC particle.

• 한국정밀공학회지
• /
• 제17권6호
• /
• pp.96-102
• /
• 2000

The finishing process for dies and molds is an important process because it has influence on final quality of products. And it is difficult to automatize finishing process so that the process has depended on expert's skill until now. However, recently a study on development of die automatic finishing machine has been progressed, and actually this machine is applied to fabrication of die. But the research about tooling system is not enough and finishing tool must have high machining efficiency and adaptability of curved surface. So, this study investigated the application of conductive elastic tool which is composed of metal-resin bonded pellet and elastic backing material. The metal-resin bonded pellet is used to finish the surface by conventional mechanical grinding or electro-chemial grinding method. And elastic backing material is used to follow the curved surface. So conductive elastic tool has long lifetime, uniform removal rate and adaptability of curved surface.

• 한국정밀공학회지
• /
• 제18권4호
• /
• pp.121-128
• /
• 2001

This study has been performed to investigate formability of non-vinyl PCM(pre-coated metal)sheet. First, physical test of PCM sheets were tested to evaluate finish coating characteristic of PCM. And then, test equipment was made for friction test and three non-vinyl PCM sheets were tested by straight pulling method. This paper provides the results of the friction tests showing the influence of sheet surface texture and process conditions. It was found that the influence of contact pressure and speed had an effect upon the level of friction. Also using tests, the scratch resistance of a series of polyester coating has been investigated. This investigation aims to clarify the process conditions that prevent the scratch of PCM to form the good electrical appliances such as microwave oven, air conditioner and refrigerator etc.

• 한국지하수토양환경학회:학술대회논문집
• /
• 한국지하수토양환경학회 1998년도 공동 심포지엄 및 추계학술발표회
• /
• pp.240-244
• /
• 1998

This study was carried out to investigate the efficiency of steel mill slag and sludge in removing heavy metals and cyanide in metal plating wastewater. Laboratory experiments were peformed with jar tester, The tests were peformed at ambient temperature. The results of tests showed that overall rates metals removed were greater than 90 %. Metals were removed from solution as the combined effects of adsorption and precipitation in alkaline condition. The removal efficiency of cyanide by steel mill wastes was above 90 % at optimum conditions. In view of the test results and other engineering characteristics of steel mill slag and sludge, these industrial by-products from steel industry have a high potential to be used in metal plating wastewater treament and were particularly beneficial.

• 한국생산제조학회지
• /
• 제24권5호
• /
• pp.489-495
• /
• 2015

Forging is a manufacturing process involving the shaping of metal using localized compressive forces and the process of deforming metal into a predetermined shape using certain tools and press according to the temperature. Forging provides stronger metal parts than that possible by casting or machining. Conventional clutch jaw parts have been developed through cold forging and precision machining; however, fabrication of integral clutch jaw parts for farm machinery has not been reported yet. These parts were developed by applying a complex forging technology combining cold and hot forging. The integrated forming technology proposed in this study will be useful for reducing the lead-time for manufacturing, improving the accuracy of products, and eliminating the welding process.

• 한국생산제조학회지
• /
• 제23권4호
• /
• pp.350-354
• /
• 2014

Recently, high strength steel (HSS) sheet metal has been widely used to improve lightweight structures in the automotive industry. Because HSS sheets have high strength but low elongation, it is difficult both to make products with complex shapes and to control excessive springback. In order to reduce the springback after forming using HSS, draw beads were introduced in this study. The design variables, including the draw-bead positions and shapes, were optimized using a finite element analysis. A mold for a scanner support, which is part of an A3 printer, was designed using the proposed method and then utilized. The results from a finite element simulation and optimization were compared with the experiment results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1998년도 춘계학술대회논문집
• /
• pp.28-31
• /
• 1998

Wrinkling is one of the major defects in sheet metal products and may be also attributable to the wear of the tool. The initiation and growth of the wrinkles are influenced by many factors such as stress state, mechanical properites of the sheet material, geometry of the body, and contact condition. It is difficult to analyze the wrinkling initiation and growth considering the factors because the effects of the factors are very complex and the wrinkling behavior may show wide variation for small deviation of the factors. In this study, the bifurcation theory is introduced for the finite element analysis of wrinkling initiation and growth, All the above mentioned factors are conveniently considered by finite element method. The finite element formulation is based on the incremental deformation theory and elastic-plastic material modeling. The finite element analysis is carried out using the continuum-based resultant shell elements considering the planar anisotropy of the sheet metal. The proposed method is verified by employing to column buckling problem. And then, the initiation and growth of wrinkling in deep drawing of cylindrical cup are analyzed.

• 한국세라믹학회지
• /
• 제23권5호
• /
• pp.86-92
• /
• 1986

As there is a growing trend to make high quality steel improving production efficiency and utilizing slag as resources the technologies of hot metal pretreatment have been progressed to meet these demands. Although mill scale $Na_2CO_3$ and CaO used as fluxes proved to be excellent agents then can severely corrode refractories such as chamotte and high alumina for torpedo or open ladle car. Thus it was considered necessary to develop new refractories which can endure suchy conditions. Desulfurization fluxes vastly used in POSCO are $CaCO_3$ and CaO Recent trials have been made by testing phenol resin bonded $Al_2O_3-SiC-C$ bricks in torpedo ladle car for hot metal pretreatment. The results showed that the life of this brick became about 1.2 times longer than that of foreign products. And the crushing strength M.O.R corrosion resistance and oxidation resistance were tested.

• 한국주조공학회지
• /
• 제25권2호
• /
• pp.80-87
• /
• 2005

The microstructure and mechanical property of the Ni and Ni-Cr porous metal reinforced AC4C matrix composites fabricated by squeeze casting were investigated. In this study Ni, Ni-Cr porous metals which are estimated to be easy to fabricate by squeeze casting are used as strengtheners for composite materials. As a matrix material, Al-7wt.%Si-0.3wt.%Mg(AC4C) has been used. In case of Ni/AC4C and Ni-Cr/AC4C composite, $750^{\circ}C$ melt temperature and minimum 25MPa squeezing pressure are needed to produce sound composite materials. The observation of interfacial reaction zone at various heat treatment condition shows that atsolutionizing temperature of above $520^{\circ}C$, the interfacial reaction zone increases proportionally with heat treatment time and the reaction products formed by interfacial reactions are mainly composed by $Al_{3}Ni$ and $Al_{3}Ni_{2}$ phases.

• 한국응용과학기술학회지
• /
• 제7권1호
• /
• pp.71-76
• /
• 1990

Transesterification reactions (methyl methacrylate with monoethanolamine, methyl methacrylate with n-butyl alcohol, dimethylphthalate with ethylene glycol, dimethyl phthalate with monoethanolamine) were kinetically investigated in the presense of various metal acetate catalysts at $110^{\circ}C$. The amount of reactants was measured by gas and liquid chromatography, and the reaction rates also measured from the amount of reaction products and reactants upon each catalyst. The transesterification reactions were carried out under the first order conditions respect to the concentration of reactants, respectively. The overall reaction order was 2nd, Maximum reaction rates were appeared at the range of 1.4 to 1.6 in electronegativity of metal ions and maximum catalytic activities were obserbed at the range of 1.5 to 1,8 in instability constant of metal acetates.