• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.1007-1013
• /
• 2003

As environmental restriction kas continuously become more strict, machining technology has emphasized on development of environment-friendly technology. In cutting technology, it has been well recognized that cutting fluids might have undesirable effects on workers health and working environment. In this study, compressed cold air was used as a replacement for conventional cutting fluids. The cooling effect on cutting tool was analyzed using the finite element method and the computational fluid dynamics. This study focused on the temperature simulation of cutting tool by real flow analysis of cold air. The maximum flow rate and the minimum temperature of compressed cold air are 300ι/min and -30$^{\circ}C$ respectively. To compare the simulation and experimental results, inner temperature of the cutting tool was measured with the thermocouple embedded in the insert. The results show that the analysis of cutting temperature using FEM and CFD is resonable, and the replacement of cutting fluid with cold air is available.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.1799-1802
• /
• 2003

The commercial success of a new product is influenced by the time to market. Shorter product leadtimes are of importance in a competitive market. This can be achieved only if the product development process can be realized in a relatively small time period. New cutting inserts are developed by a time consuming trial and error process guided by empirical knowledge of the mechanical cutting process. The effect of previous cutting on chip formation and the surface residual stresses has been studied. The chip formation is not affected much. There is only a minor influence from the residual stress on the surface from tile first cutting on the second pass chip formation. Thus, it is deemed to be sufficient to simulate only the first pass. The influence of the cutting speed and feed on the residual stresses has been computed and verified by the experiments. It is shown that the state of residual stresses in the workpiece increases with the cutting speed. This paper presents experimental results which can be used for evaluating computational models to assure robust solutions. The general finite element code ABAQUS/Standard has been used in the simulations. A quasi-static simulation with adiabatic heating was performed. The path for separating the chip from the workpiece is predetermined. The agreement between measurements and calculation is good considering the simplifications introduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.5 no.1
• /
• pp.40-49
• /
• 1988

The chip control problem is one of the important subjects to be studied in the metal cutting process. Especially, an important practical problem concerns the form of chips pro- duced in machining since this has important implications relative to : 1. Personal safety. 2. Possible damage to equipment and product. 3. Handling and disposal of swarf after machining. 4. Cutting forces, temperatures, and tool life. However, a dependable way to predict the form of chips in a wide range of cutting conditions has not been established satisfactorily. In this paper, the relationship between the form of chips and the ratios of cutting forces were studied experimentally. According to what the experiments have been carried out in the turning process the main results can be summarized as follows : 1. By use of the multiple linear regression model, emperical formulas which are suitable to wide ranges of cutting conditions with accuracy were obtained satisfactorily. 2. The correlations between the form of chips based upon the classification by Henriksen and the ratios of cutting forces, namely (feeding force/thrust force), (principal force/feeding force) were determined. 3. Using above results, the algorithms which predict the form of chips were constituted. With these algorithms, the form of chips in a wide range of cutting of cutting conditions can be predicted.

• Design & Manufacturing
• /
• v.13 no.1
• /
• pp.5-12
• /
• 2019

In this paper, we studied the micro tool deflection, micro cutting with low temperature, and deformation of micro ribs caused by cutting forces. First, we performed an integrated machining error compensation method based on captured images of tool deflection shapes in micro cutting process. In micro cutting process, micro tool deflection generates very serious problems in contrast to macro tool deflection. To get the real images of micro tool deflection, it is possible to estimate tool deflection in cutting conditions modeled and to compensate for machining errors using an iterative algorithm correcting tool path. Second, in macro cutting fields, the cryogenic cutting process has been applied to cut the refractory metal but, the serious problem may be generated in micro cutting fields by the cryogenic environment. However, if the proper low temperature is applied to micro cutting area, the cooling effect of cutting heat is expected. Such effect can make the reduction of tool wear and burr formation. For verifying this passibility, the micro cutting experiment at low temperature was performed and SEM images were analyzed. Third, the micro pattern was deformed by the cutting forces and the shape error occurred in the sidewall multi-step cutting process were minimized. As the results, the relationship between the cutting conditions and the deformation of micro-structure during micro cutting process was investigated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.6
• /
• pp.1121-1140
• /
• 1992

In metal cutting the shape of generated chip varies according to cutting conditions, characteristics of workpiece and geometry of cutting tool. The best surface roughness of machined workpiece is obtained when generating flow type contrinuous chip. If the generated chip is not broken, that is not only tangled workpiece and cutting tool, but also may give damage on the machined surface of workpiece or danger for a operator. The flow type continuous chip may bring the low productivity in high speed any heavy cutting, automatic machining process and non-human factory. There are two type of chip break process ; controlling cutting condition and using chip breaker. In present study we carried out the experiment on new type chip breaker compared with conventional type and proved the efficiency of a new type and showed the chip break condition to be applied in actual metal cutting. In the experiment SM 20 C as a workpiece material and WC as a tool material were used and cutting speed of 30-150m/min, feed of 0.071-0.210mm/rev and depth of cut of 1mm were applied as cutting condition. The results of the experiment are as follows : (1) The mechanism of chip curl can be explained more clearly by plastic flow of workpiece material and moment of shearing force. (2) The most effective radius of curled chip and flat distance from cutting edge is 2.0-2.5mm and 1.5mm in both types. (3) The effective inclination angle of chip break surface and side cutting edge angle are 30.deg.- 45.deg. and 20.deg. in conventional type, while the radius of arc surface, lower arc angle A, upper arc angle B and side cutting edge angle are 3mm, 20.deg.- 45.deg., 0.deg.- 45.deg. and 10.deg.- 20.deg. in new type. (4) The probability to be obtained 100% chip breaking ratio is much higher in new type than in conventional type.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.1
• /
• pp.131-137
• /
• 1986

Cutting oil cools the chip and a tool as well as lubricates the chip-tool interface, the flank and machined surface. Rehbinder effect has been known as a phenomenon, the reduction of mechanical strength, when the metal is exposed to a polar organic environment or the surface of metal is coated with some polar organic substances. About the cause of Rehbinder effect there have been many different ideas by Rehbinder, Shaw, Barlow, Sakida and etc. In this report, the efect of polar organic substance( $C_{6}$ $H_{5}$C $H_{3}$+ $C_{6}$ $H_{4}$(C $H_{3}$)$_{2}$+ $C_{4}$ $H_{9}$OH+ $C_{6}$ $H_{12}$ $O_{2}$) (magic ink) upon the mechanism of chip formation on the orthogonal cutting of copper and mechanical properties of the work material are experimentally discussed with various rake angles. As expected no lubrication action could be noticed, but the shear angle increased and the cutting force and shear strain on the shear plane decreased, therefore the work material must be embrittled under polar organic substance.substance.

• Journal of Powder Materials
• /
• v.20 no.5
• /
• pp.355-358
• /
• 2013

Micro trench structures are applied in gratings, security films, wave guides, and micro fluidics. These micro trench structures have commonly been fabricated by micro electro mechanical system (MEMS) process. However, if the micro trench structures are machined using a diamond tool on large area plate, the resulting process is the most effective manufacturing method for products with high quality surfaces and outstanding optical characteristics. A nonferrous metal has been used as a workpiece; recently, and hybrid materials, including polymer materials, have been applied to mold for display fields. Thus, the machining characteristics of polymer materials should be analyzed. In this study, machining characteristics were compared between nonferrous metals and polymer materials using single crystal diamond (SCD) tools; the use of such materials is increasing in machining applications. The experiment was conducted using a square type diamond tool and a shaper machine tool with cutting depths of 2, 4, 6 and 10 ${\mu}m$ and a cutting speed of 200 mm/s. The machined surfaces, chip, and cutting force were compared through the experiment.

• Journal of the Korean Society for Precision Engineering
• /
• v.1 no.2
• /
• pp.24-32
• /
• 1984

The object of the study is to discuss the effect of magic ink as a surface active substance on the mechanism of chip formation in oblique cutting. The Rehbinder effect has been known as a phenomenon that the mechanical strength reduces when the metal is coated with some surface active substances. In order to interpret these surface effects defined by Rehbinder, the influence on the shear strength of shear plane by coating surface active substances, cutting force by the depth of cut, surface roughness and hardness ratio were observed. The results are as follows: 1. By coating the magic ink on free surface of the forming chip, the effective shear angle increases, and the cuttinbg force and the deformed chip thickness decreases. 2. With the large inclination angle the effective shear angle increases, and the specific cutting force and the friction angle decrease. 3. Cutting of the coated surface improves the surface roughness and the hardness ratio drops, which means another Rehbinder effect.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.259-264
• /
• 1995

Recently, in order to achieve high flexibilty, monitoring and control strategies of a new type have been developed. This paper investigates the fesability of using scoustic emission signal analysis for the detection of built-up edge during machining. Results for maching SM45C steel show that the presence of a built-up edge can significantil affect the generation of acoustic emission in metal cutting. When the cutting speed comes to the conditions conducive to development of built-up edge, it is shown that the slope of curve-fitted AErms signal undergoes a change. The fesability of utilizing AErms in built-up edge sensing is sugested.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.04a
• /
• pp.388-392
• /
• 2003

As the machine tool industry progresses, the performance of cutting tools also needs to be of good quality and specialized. If the existing metal cutting tool tip is coated properly, its life would be longer and the machining of a difficult-to-cut material also could be possible. For the development of the high quality cutting tool, the applicabilities of TiAIN coating deposited by PVD on the cutting insert were experimentally investigated. The various measurements, such as, SEM micrograph, XRD pattern, AFM surface morphology, and hardness were performed to cross-check the possibility and availability of TiAIN coated tool in the field. The effects of it is successful and we hope to see good results in many fields.