• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.4
• /
• pp.543-549
• /
• 1997

The problems in the existing modeling rules for fishing nets, especially in the Tauti's rule which had been used most commonly, were investigated and it was found that the rules could not give a good similarity between the prototype and model nets because they din neither analyze the flow resistance of nets accurately nor decide the ratio of flow velocity between the two nets properly. Thus, the modeling rule was newly derived by regarding the nets as holey structures sucking water into their mouth and then filtering water through their meshes as in the previous paper. The similarity conditions obtained, between the two nets distinguished by subscript 1 and 2, are as follows; $$\frac{d_2}{d_1}=\sqrt{\frac{l_2}{l_1}},\;\frac{N_2}{N_1}=(\frac{d_1}{d_2})^{1.5}\frac{L_2}{L_1},\;\varphi_1=\varphi_2,\;\frac{d_{r2}}{d_{r1}}=\sqrt{\frac{L_2{(\rho_{r1}-\rho_{w1})}}{{L_1{(\rho_{r2}-\rho_{w2})}}$$ $$\frac{N_{a2}}{N_{a1}}=\frac{W_{a1}}{W_{a2}}(\frac{L_2}{L_1})^2,\;\nu_1=\nu_2\;and\;\frac{R_2}{R_1}=(\frac{L_2}{L_1})^2$$, where L is the length of nettings, d the diameter of netting twines, 2l the mesh size, $2\varphi$ the angle between two adjacent bars, N the number of meshes at the sides of nettings, $d_r$, the diameter of ropes, $\rho_r$, the specific gravity of ropes, $W_a$ the weight in water of one piece of float or sinker, $N_a$ the number of floats or sinkers, $\nu$ the flow velocity, and R the flow resistance of net. In the case where the model experiments aim at investigating the influence of weight in water of nettings on their shapes in nets subjected to the water flow of very low velocity, however, the following condition is added; $$\frac{\rho_2-\rho_{w2}}{\rho_1-\rho_{w1}}=\frac{d_1}{d_2}$$ where $\rho$ is the specific gravity of netting twines.

• Journal of Yeungnam Medical Science
• /
• v.11 no.2
• /
• pp.293-302
• /
• 1994

The objective of this study was to establish a good methodology to isolate single smooth muscle cells that are alive and respond properly to pharmacological agents. Canine urinary bladders were employed as the source of single cells, and acetylcholine, atropine and imipramine were used as indicators of pharmacological responsiveness. Imipramine, an antidepressant drug exhibited the anticholinergic and calcium antagonizing properties on rat detrusor muscle. To establish a control value for a further experiment to elucidate the mechanism of action of imipramine on detrusor muscle, we measured the concentration-response of single cells to acetylcholine in the presesnce of imipramine by length of the cells and compared the result with the response in the presence of atropine. Tiny chops of smooth muscle taken from anesthetized canine urinary bladder were incubated in collagenase solution at $36^{\circ}C$ for 17-20 minutes. The collagenase solution included collagenase 1.2 mg/ml, soybean tryspin inhibitor 0.08 mg/ml, bovine serum albumin 2% in 10 ml Krebs-Henseleit buffer solution aerated with a consistent breeze of 95/5% $O_2/CO_2$, to maintain the pH at 7.4. After washing with plain K-H solution on 450 mesh, cells were dissociated from the digested tissue for 12-15 minutes. Cell suspension was transfered in 5 ml test tubes and acetylcholine was added for the final concentration to be $10^{-14}M{\sim}10^{-9}M$. To find the optimal time to fix the cells to determine the contractile responses, 1% acrolein was added 5, 10, 20, 30, 60 and 120 seconds after the administration of ACh. The length of cells fixed by acrolein were measured by microscaler via CCTV camera on phaes-contrast microscope. The average length of 50 cells from a slide glass was taken as the value of a sample at the very concentration point. Single cells were isolated from canine detrusor. The length of untreated cells varied from 82 ${\mu}m$ to 94 ${\mu}m$. The maximal response to actylcholine $10^{-9}M$ was accomplished within 5 seconds of exposure, and the shortening was $19{\pm}3$%. Atropine reduced the contraction of the cells concentration-dependently. Imipramine which exerts a cholinergic blocking action on some smooth muscles also reduced the contraction concentration-dependently and by a similar pattern as atropine. These findings document that imipramine may exerts a cholinergic blocking activity in the single smooth muscle cells isolated from canine urinary bladder.

• Journal of Aquaculture
• /
• v.11 no.3
• /
• pp.371-380
• /
• 1998

This study has been conducted to develop the techniques for spat production of the sun and moon scallop from January 1995 to December 1996. With the adult scallops collected from the Sogwipo area, spawning induction and larvae rearing were attempted several times and monthly changes of GSI were also monitored during the experimental period. The results obtained wre as follows. 1. GSI started to increase from June and showed the maximum value of 22.17 and 14.98 in female and male respectively in November, and then gradually decreased from December. 2. Spawning induction by heating method turned out to the most efficient way showing the responding rate of 64.8~91.5%. The responding temperature was $21.4~26.4{\circ}C$ which was $3.1~8.5{\circ}C$ increased from the rearing temperature of $16.3~18.3{\circ}C$. An average number of eggs spawned was $9.2{\times}10^5$ 3. the average size of eggs after fertilization was about $72{\mu}m$ in diameter. The first polar body discharge, blastula formation, and trochopore larvae appearance occurred 30 mininutes, 18 hours, and 22 hours after fertilization respectively. 4. Settling rates in various collectors were similar one another, whereas pouring larvae in the mesh was the most efficient way for larval setting. 5. The spates grew to be 1mm in their shell length for the first 50 days after fertilization and 9.6mm in 135days. 6. Correlation between shell length (SL) of the spat and the number of days (X) after spat settlement could be expressed as $SL=257.75e ^{0.0272x}$(r=0.9100).

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.21 no.1
• /
• pp.21-29
• /
• 1988

This study was carried out to develop the powdered Katsuobushi (a kind of boiled, smoked, and dried fish product which is used for seasoning soup as it is.) using skipjack as a natural flavoring substance. The processing conditions of the powdered Katsuobushi and the changes of taste compounds during processing of the products were examined. In preparation of the powdered Katsuobushl, frozen skipjack was thawed, beheaded, gutted, filleted and then sliced to 1cm of thickness. The silted meats were boiled in skipjack extract for 20 minutes, and then it was smoked for, 3 times to $10\~12\%$ moisture content at $80^{\circ}C$ for 8 hours. The smoked - dried meats were followed to be 50 mesh of particle size. The effect of slicing and boiling in skipjack meat extract on enhancing flavor and on preventing lipid oxidation of product during processing were observed. The moisture content and crude lipid content of the powdered Katsuobushi was in the range of 11 to $12\%$ and 4.3 to $4.8\%$, respectively. The taste compounds of the product were nucleotides and their related compounds, 1135.8mg/100g ; free amino acid and related compounds, 2210.2mg/100g ; non-volatile organic acids, 1148.0mg/100g ; and total creatinine. 592.1mg/100g on dry basis, and small amount of betaine and TMAO. The major elements of mineral in the product were found to be K, Mg, Na, and Ca. The content of IMP was 542.0mg/100g, and major free amino acids were found to be histidine, anserine, taurine, carnosine and alanine of which occupied to $83.6\%$ of total free amino acids. In non -volatile organic acids, major ones were lactic acid, succinic acid, pyroglutamic acid and $\alpha-ketoglutaric$ acid. From the results of the chemical experiments and sensory evaluation, we may conclude that the flavor of the product from present experiment is more desirable than that of conventional products although the processing time used were much shortened than that of conventional method, and it can be commercialized as a seasoning powder.

• Korean Journal of Ecology and Environment
• /
• v.41 no.3
• /
• pp.402-411
• /
• 2008

Grazing effects of two freshwater shellfish, Unio douglasiae (UNIO) and Cipangoplaudina chinese malleata (CCM), on the hibernal diatom communities in eutrophic water was examined in a laboratory. Two animals having different feeding types used in the study were collected from Keum River (Boryeong, Korea), acclimatized in the artificial management system in a laboratory over at least one month, and starved in a laboratory for 2 days before the experiment. Experimental waters, which dominated by Synedra ulna-Scenedesmus sp. (ca. 80%), was collected from eutrophic lake, Lake Ilgam (Seoul) in Feb., 19, 2008 at AM 10:00, and used in the study after the filtration with 1 mm Nylon mesh. Feeding experiments were largely divided into three kinds of animal treatments; five densities of UNIO (U0, U1, U2, U3, U4) and CCM (C0, C1, C2, C3, C4), and four combined densities of two shellfish (M0, M1, M2, M3). U0 and C0 were control (no addition of UNIO or CCM), U1 or C1 (each animal density at 0.5 ind. $L^{-1}$), U2 or C2 (1.0 ind. $L^{-1}$), U3 or C3 (1.5 ind. $L^{-1}$), and U4 or C4 (2.0 ind. $L^{-1}$), respectively. Four combined treatments were consisted of M0 (no animals), M1 (U1+C3), M2 (U2+C2), and M3 (U4+C1), respectively. Under the presence of animal, the concentration of Chl-a and algal abundance were clearly decreased with the increase of UNIO density and the treated time, while in combined group a strong decrease of algal density showed with the increase of UNIO density. Total phytoplankton density shifted as the similar patterns to that of Chl-a concentration (r=0.6527, p<0.0001), however, there showed the differences following a species. There were strong decreases of dominant species Synedra ulna, Scenedesmus sp., Ankistrodesmus falcatus in UNIO treatment group, Diatoma vulgare in combined group, while Cryptomonas ovata in high density of CCM increased about 20% in algal density. Grazing rates (GRs) based on the concentration of Chl-a was depend on the kind of shellfish and treatment time; a strong feeding of CCM showed in the initial stage, and four hours later, UNIO and combined group with high UNIO density showed the high GRs. Interestingly, faeces production of shellfish was highest in combined group with high density of CCM, while their size over 60 ${\mu}m$ was much higher in production magnitude than that less 60 ${\mu}m$. Collectively, these results suggest that two domestic shellfish and its combined treatment have a strong potential as an effective biological controller of diatom bloom in cold eutrophic waters.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.30 no.5
• /
• pp.691-699
• /
• 1997

In order to find out the properties in flow resistance of trawlR=1.5R=1.5\;S\;v^{1.8}\;S\;v^{1.8} nets and the exact expression for the resistance R (kg) under the water flow of velocity v(m/sec), the experimental data on R obtained by other, investigators were pigeonholed into the form of $R=kSv^2$, where $k(kg{\cdot}sec^2/m^4)$ was the resistance coefficient and $S(m^2)$ the wall area of nets, and then k was analyzed by the resistance formular obtained in the previous paper. The analyzation produced the coefficient k expressed as $$k=4.5(\frac{S_n}{S_m})^{1.2}v^{-0.2}$$ in case of bottom trawl nets and as $$k=5.1\lambda^{-0.1}(\frac{S_n}{S_m})^{1.2}v^{-0.2}$$ in midwater trawl nets, where $S_m(m^2)$ was the cross-sectional area of net mouths, $S_n(m^2)$ the area of nets projected to the plane perpendicular to the water flow and $\lambda$ the representitive size of nettings given by ${\pi}d^2/2/sin2\varphi$ (d : twine diameter, 2l: mesh size, $2\varphi$ : angle between two adjacent bars). The value of $S_n/S_m$ could be calculated from the cone-shaped bag nets equal in S with the trawl nets. In the ordinary trawl nets generalized in the method of design, however, the flow resistance R (kg) could be expressed as $$R=1.5\;S\;v^{1.8}$$ in bottom trawl nets and $$R=0.7\;S\;v^{1.8}$$ in midwater trawl nets.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.2
• /
• pp.121-126
• /
• 1999

In order to degrade chitin by enzymatic hydrolysis, it is required from screening highly active deacetylase. To this end, we examined three fungal strains and it turned out that Mucor rouxii produced highly active deacetylase, this enzyme exhibited the highest enzymatic activity against colloidal chitin. The conditions for growing Mucor rouxii are as follows; the effective carbon source, nitrogen source, adequate initial pH, temperature and incubation time were $2\%$ glucose, $1.33\%$ yeast extract, $0.66\%$ pepton, 4.5, $25{\pm}2^{\circ}C$ and 48hr, respectively. The optimum pH and temperature for purified enzyme activity were 5.5 and $40^{\circ}C$, respectively. The purified enzyme was stable at pH ranging from 4.5 to 5.5. However, the enzyme activity was decreased to less than $50\%$ at pH blow 45 and above 7.5. At temperatures above $50^{\circ}C$, the enzyme activity was decreased remarkably. The enzyme was inhibited by LiC1, $HgCl_2$, and $BaCl_2$, but stimulated by $CaCl_2$ and $ZnC1_2$, The activity of purified enzyme was increased by L-cysteine and 2-mercaptoethanol, while decreased by O-phenanthroline, p-CMB, EDTA, and iodoacetate. The $K_m$ and the $V_{max}$ value of purified enzyme were $1.2\%$ and 59.5 U/mg, respectively. The deacetylation activity of purified enzyme was not detected at optimal reaction condition when chitin particle suspension was used.

• Resources Recycling
• /
• v.5 no.4
• /
• pp.32-41
• /
• 1996

The objective of this study was to investigate the facton affecting the property of CaCO, farmed from CaClz-Na,CO,-HiOsystem. The effcct of the concentmtlon of reaclants, impurity, the pH of reaction, the addition of sccd crystal, and injectingvelocity af reaclant solution an thc yield oI CaCO; polymorphs. parlide size and whiteness of CaCO, were investigated. Thcmqor resulls are ;o fallows; I The optimum concentratinn of reildilnts for forming vaterlte and aragonite is the range of 0.1-1.0 mol/l, when the yicld of vittcrite and araga~nles howed 7542% and XU-90%. respedively. 2. Among thc composition of impunticscontained h limestone, Fe' decrease the wh~tcness nf CaCO;. md Mg" increase the yield of aragonite. 3. The pHrange of vaterite and aragonite are formed with high yield is 8-11, and Calcite is famed in pH 6-8 with big particle size of 1over and in pH 11-13 with small particle size of I under. 4. The yicld of calcite and aragonite was increased by addingthc seed cryst.al nf itself.d cryst.al nf itself.

• The Journal of Korean Academy of Prosthodontics
• /
• v.49 no.4
• /
• pp.316-323
• /
• 2011

Purpose: The purpose of this study was to investigate the effect of different thread designs on the marginal bone stresses around dental implant. Materials and methods: Standard ITI implant(ITI Dental Implant System; Straumann AG, Waldenburg, Switzerland), 4.1 mm in diameter and 10 mm in length, was selected as control. Test implants of four different thread patterns were created based on control implant, i.e. maintaining all geometrical design of control implant except thread pattern. Four thread designs used in test implants include (1) small V-shape screw (model A), (2) large V-shape screw (model B), (3) buttress screw (model C), and (4) trapezoid screw (model D). Surface area for unit length of implant was 14.4 $mm^2$ (control), 21.7 (small V-shape screw), 20.6 (large V-shape screw), 17.0 (buttress screw) and 28.7 $mm^2$ (trapezoid screw). Finite element models of implant/bone complex were created using an axisymmetric scheme with the use of NISA II/DISPLAY III (Engineering Mechanics Research Corporation, Troy, MI, USA). A load of 100 N applied to the central node on the crown top either in parallel direction or at 30 degree to the implant axis (in order to apply non-axial load to the implant NKTP type 34 element was employed). Quantification and comparison of the peak stress in the marginal bone of each implant model was made using a series of regression analyses based on the stress data calculated at the 5 reference points which were set at 0.2, 0.4, 0.6, 0.8 and 1.0 mm from implant wall on the marginal bone surface. Results: Results showed that although severe stress concentration on the marginal bone cannot be avoided a substantial reduction in the peak stress is achievable using different thread design. The peak marginal bone stresses under vertical loading condition were 7.84, 6.45, 5.96, 6.85, 5.39 MPa for control and model A, B, C and D, respectively. And 29.18, 26.45, 25.12, 27.37, 23.58 MPa when subject to inclined loading. Conclusion: It was concluded that the thread design is an important influential factor to the marginal bone stresses.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.36 no.4
• /
• pp.94-104
• /
• 2018

This study examined photogrammetric reconstruction techniques that can measure the original form of a cultural property utilizing photographs taken in the past. During the research process, photographs taken in the past as well as photograph on the internet of Soswaewon Garden in Damyang(scenic site 40) were collected and utilized. The landscaping structures of Maedae, Aiyangdan, Ogokmun Wall, and Yakjak and natural scenery Gwangseok, of which photographs can be taken from any 360 degree direction from a close distance or a far distance without any barriers in the way, were selected and tested for the possibility of reproducing three-dimensional shapes. The photography method of 151 landscape photographs (58.6%) from internet portal sites for the aforementioned five landscape subjects containing information on the date the photograph was taken, focal length, and exposure were analyzed. As a result of the analysis, it was revealed that the majority of the photographs tend to focus on important parts of each subject. In addition, we discovered that there are two or three photography methods that internet users preferred in regards to each landscape subject. For the purposes of the experiment, photographs in which a single scene consistently appears for each landscape subject and it was determined that there was a high level of preference related to the photography method were analyzed, and three-dimensional mesh shape model was produced with a photoscan program to analyze the reproducibility of three-dimensional shapes. Based on the results of the reproduction, it was relatively possible to reproduce three-dimensional shapes for artifacts such as Ogukmun wall, Maedae, and Aeyangdan, but it was impossible to reproduce three-dimensional images for natural scenery or an object that has similar texture such as Yakjak and Gwangseok. As a result of experimentation related to the reconstruction of three-dimensional shapes with the photographs taken on site using a photography method similar to that of the photographs selected as previously mentioned, there was success related to reproducing the three-dimensional shapes of Yakjak and Gwangseok, of which it was not possible to do so through the photographs that had been collected previously. In addition, through comparison of past and present images, it was possible to measure the exact sizes as well as discover any changes that have taken place. If past photographs taken by tourists or landscape architects of cultural properties can be obtained, the three-dimensional shapes from a particular period of time can be reproduced. If this technology becomes widespread, it will increase the level of accuracy and reliability in regards to measuring the past shapes of cultural landscape properties and examining any changes to the properties.