• 한국식품조리과학회지
• /
• 제12권1호
• /
• pp.20-26
• /
• 1996

The present study was attempted to investigate and to evaluate various hydrocolloids as a stabilizer in improving texture of the frozen yogurt. Four kinds of hydrocolloids used in this study were CMC (carboxymethyll cellulose), PGA(propylene glycol alginate), LMP(low methoxyl pectin), and the combination of LBG(locust bean gum) and GG(guar gum). The viscosity of frozen yogurt mixes did not show any significant differences among four samples at 5$^{\circ}C$. However, as the temperature increased up to 50$^{\circ}C$, theviscosity of frozen yogurt mixes containing CMC, LMP, PGA decreased drastically except frozen yogurt containing the combination of LBG+GG. The overrun of frozen yogurt containing each hydrocolloid gradually increased and reached to about 53, 50, 54, and 35%, respectively, after 40 min of operating ice cream freezer. As the result of sensory evaluation in the texture of frozen yogurt and melt-down quality, the sample containing LMP was described as the most coarce & icy, crumbly, and sand-like characters. On the other hand, PGA sample was evaluated as not being icy, crumbly, but being chewy and soft in texture. However, any significant differences among four samples were not shown in melt-down quality.

• 소성∙가공
• /
• 제15권8호
• /
• pp.586-590
• /
• 2006

42Ni-Fe Invar alloy strips were fabricated using conventional ingot casting and melt drag casting followed by rolling. Mechanical properties such as tensile strength, elongation and blanking deformability of the strips were evaluated. The properties were strongly depended on fabrication methods. Tensile strength and elongation of all strips were in the range of $40-60kg/mm^{2}$ and 26-35%, respectively, which are enough values for the manufacture of the final products. In some of the strips, however, burrs occurred at deformed surface. The properties of strips were explained in terms of microstructure such as grain size and texture formation during rolling. Additionally, strips by melt drag casting method were compared to those by conventional ingot casting.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2009년도 Korea Superconductivity Society Meeting 2009
• /
• pp.15-15
• /
• 2009

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.166-169
• /
• 2004

Permalloys were successfully fabricated by melt drag casting in the present study, and their variation of microstructure and consequent magnetic properties were investigated as a function of Si contents and annealing temperature. The increases in Si content and annealing temperature resulted in the increases of grain size and amount of $FeNi_3$ ordered phase. Both the grain size and $FeNi_3$ ordered phase controlled by Si and annealing temperature had a important role on permeability of permalloys.

• 소성∙가공
• /
• 제13권6호
• /
• pp.522-527
• /
• 2004

Permalloys were successfully fabricated by melt drag casting in the present study, and their microstructure and consequent magnetic properties have been investigated as a function of Si content. In order to understand the relationship between magnetic properties and Si content, microstructure and texture were observed and phase analysis were performed by TEM. The effective permeability went through a maximum value at $2\%$ Si and then decreased with increasing Si content. Increasing Si content enlarged grain size, which resulted in improvement of permeability. However, over-added Si caused the formation of $Ni_3Fe$ order phase so that $5\%$ Si added permalloys had the smallest permeability.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.475-478
• /
• 2005

Permalloys were successfully fabricated by melt drag casting in the present study, and their variation of microstructure and consequent magnetic properties were investigated as a function of Si contents and annealing temperature. The increases in Si content and annealing temperature resulted in the increases of grain size and amount of $Ni_3Fe$ ordered phase. Both the grain size and $Ni_3Fe$ ordered phase controlled by Si and annealing temperature had a important role on permeability of permalloys.

• Carbon letters
• /
• 제24권
• /
• pp.28-35
• /
• 2017

We demonstrated an effective way of preparing melt spinnable mesophase pitches via catalytic hydrogenation of petroleum residue (fluidized catalytic cracking-decant oil) and their subsequent thermal soaking. The mesophase pitches thus obtained were analyzed in terms of their viscosity, elemental composition, solubility, molecular weight, softening point and optical texture. We found that zeolite-induced catalytic hydrogenation under high hydrogen pressure contributed to a large variation in the properties of the pitches. As the hydrogen pressure increased, the C/H ratio decreased, and the solubility in n-hexane increased. The mesophase pitch with entirely anisotropic domains of flow texture exhibited good meltspinnability. The mesophase carbon fibers obtained from the catalytically hydrogenated petroleum residue showed moderate mechanical properties.

• 한국세라믹학회지
• /
• 제42권6호
• /
• pp.437-442
• /
• 2005

We fabricated BSCCO-2212 (2212) bulk superconductor by melt casting process, and evaluated the dependence of the critical properties on the temperature and cooling .ate of mold and the pouring methods of melt. It was observed that the critical current (Ic) of 2212 was significantly dependent on the pre-heating temperature of the mold. At the pre-heating temperature of $500^{\circ}C$ followed by air cooling condition, Ic of 48 A at 77 K was obtained which was higher than others processed at different temperatures. In addition, the Ic improved to 132 A when tilt casting method was applied. The improved Ic is probably due to the fact that the tilt casting reduced a turbulent flow of the melt during casting causing less porosity and more homogeneous microsructure. Critical temperature was measured to be 87-89 K after the first heat treatment and it improved to 90-91 K when subsequently heat treated at $650^{\circ}C$ in a nitrogen atmosphere. This improvement was considered to be due to an optimization of the oxygen content in the range of 8.16-8.2.

• 한국전기전자재료학회논문지
• /
• 제19권6호
• /
• pp.579-585
• /
• 2006

We fabricated BSCCO-2212 (2212) rod by the melt casting process (MCP) and evaluated the effect of the melt flowing on the critical current ($I_c$) by using vertical and tilt casting. It was observed that the $2212-SrSO_4$ rod processed by the tilt casting method with homogeneous pre-heating temperature of the mold had a higher $I_c$ than that processed by the vertical casting method. We also evaluated the influence of the strontium sulfates ($SrSO_4$) addition on the texture, microstructure, critical current and temperature, and mechanical hardness of the $2212-SrSO_4$ rods. It was observed that the addition of $SrSO_4$ improved the critical current ($I_c$) and mechanical hardness of the 2212. The $I_c$ of the 2212 increased as the $SrSO_4$ content increased and reached a peak value (260 A at 77 K) at an $SrSO_4$ content of 6 wt.%. In addition, the addition of $SrSO_4$ had a beneficial effect on the mechanical hardness of the 2212. We studied the possible cause of the variation in the $I_c$ with the melt flowing and the $SrSO_4$ content based on the XRD, EPMA analysis and the microstructural observation.

• 한국세라믹학회지
• /
• 제35권1호
• /
• pp.79-87
• /
• 1998

Melt spun YbBa2Cu3Agx(x=0, 5, 12, 16 and 53) precursor alloy ribbons were oxidized at 263-330$^{\circ}C$ and treated at 820$^{\circ}C$, 855$^{\circ}C$ and 885$^{\circ}C$ under 1.0 atm oxygen pressure. In the ribbons treated at 820$^{\circ}C$, 855$^{\circ}C$and 885$^{\circ}C$ 1-2-4 phase (YbBa2Cu4O8) and 1-2-3 phase (YbBa2Cu3O{{{{ OMICRON _7-$\delta$ }})were formed respectively. The shape of 1-2-4 phase was distorted or ellipsoid. The 2-4-7 and 1-2-3 phases tooked the shape of bar. All the ribbons showed zero critical current density Jc at 77K in zero magnetic field. By considering the shape and the highest critical temperature (among the three phases) of the 1-2-3 phase we tried to increase the critical current density of the ribbons treated at 885$^{\circ}C$ by press deformation. About tenribbons were stacked and coupled by press deformation and then treated at 885$^{\circ}C$ These 1-2-3 phase did not show any texture in any of the ribbons. However they exhibited weak texture in the multilayered specimens. Among the multilayered specimens YbBa2Cu3Ag16 exhibited a Jc of 180 A/cm2 Among the above ribbons YbBa2Cu3Ag16 ribbon has the optimum composition to produce textured superconducting oxide with improved Jc by press deformation. Onset critical temperatures Ton of the multilayered YbBa2Cu3Agx(x=5, 12, 16 and 53) were measured as 88-90 K.