• Advances in materials Research
• /
• v.3 no.2
• /
• pp.91-103
• /
• 2014

A study that demonstrates how to investigate the molded part quality and the consistency of injection process based on the rheological concept is proposed. It is important for plastic material whose melt viscosity is variable with respect to the processing condition. The formulations to couple the melt viscosity with injection pressure and fill time are derived first. Taking calculations of the measured pressure and the time by using these formulations, the melt viscosity in injection process can be determined on machine. As the relation between the injection speed and the melt viscosity is constructed, the influences of the setting parameter of injection machine on the molded part quality can be investigated through evaluating the state of the melt viscosity. In addition, a pressure sensor bushing (PSB) designed with a quick installation feature is also provided and validated. The results show that a higher injection speed improves the tensile strength of the molded part but also the consistency of the molded part quality. This work provides an alternative to evaluate the molding quality scientifically.

• Korea-Australia Rheology Journal
• /
• v.16 no.1
• /
• pp.27-33
• /
• 2004

Application of gas assisted injection molding has been expanded during last two decades because of many advantages such as design flexibility, dimensional stability, reduction of machine tonnages, and so on. However, the surface defects including hesitation mark and gloss difference are observed for thick parts. Difficulties in lay-out of the gas channel and processing condition are another disadvantages. Liquid gas assisted injection molding(LGAIM), in which a liquid with a boiling point lower than the temperature of the polymer melt is injected into the melt stream, and travels with the melt into the mold where it vaporizes and pushes the melt downstream and against the cavity walls to create hollow channels within the part, is a good alternative of the conventional gas assisted injection molding especially in manufacturing simple and very thick parts. Though this is a new frontier of the innovation in the injection molding industry, there is no guideline for the design and processing conditions. In this paper, theoretical analysis has been made to describe the hollow formation dynamics in LGAIM. This model provides an insight into LGAIM process: explains why LGAIM has advantages over conventional gas assisted injection molding, and gives a guideline for the design and processing conditions.

• Journal of Welding and Joining
• /
• v.26 no.2
• /
• pp.92-97
• /
• 2008

In welding of thin plate, some defects such as melt through and unmelted zone occur easily at welding start, however there is a limited study on those problems. Therefore the effects of start block and arc length on melt through and unmelted zone at start were investigated in this study. When start block height was lower than base metal, there was melt through at start. And when the height was even with base metal, no unmelted zone existed. Unmelted zone was increased as start block height increased from 0mm to 0.5mm. However unmelted zone was not much changed as the height increasing from 0.5mm to 1.0mm. When gap existed between start block and base metal, melt through occurred. However, unmelted zone was increased as the contact force of start block on base metal was increased from 0kgf to 7.5kgf. And when arc length was decreased from 3.8mm to 3.0mm, unmelted zone was decreased. It was concluded that the optimum condition to prevent melt through and to minimize unmelted zone would be with start block height 0.25mm, contact force 3.0kgf, and arc length 3.4mm. This optimum condition was applied to the mass production line and resulted in satisfied outcome.

• Journal of Ceramic Processing Research
• /
• v.20 no.3
• /
• pp.276-279
• /
• 2019

New green-emitting Sr4ScAl3O10:Eu2+ phosphor was prepared using a novel melt quenching synthesis method. The temperature of raw materials irradiated with the strong light of the Xe arc-lamp was rose up to about 2273 K, followed by a sharp drop in the temperature after turn off the lamp. This method is a useful tool for rapid screening of novel phosphor materials.

• Journal of Korea Foundry Society
• /
• v.13 no.5
• /
• pp.441-449
• /
• 1993

SiC particulate reinforced magnesium matrix composites were fabricated by melt stirring method. The effet of several factors on mechanical properties and the efficiency of melt stirring method from the viewpoint of these properties were investigated. The tensile strength increased and the elongation decreased with decrease of the particle size or the increase of the paticulate volume fraction for pure magnesium matrix and Mg-5%Zn alloy matrix composites. A longer stirring time improved the tensile strength of these composites. The tensile strength of Mg-5%Ca alloy matrix composites which shows no uniform paticulate distribution was a little lower than that of matrix alloy. Rapid solidification rate is preferred for the improved tensile strength of these composites. The pure magnesium matrix and Mg-5%Zn alloy matrix composites have tensile strength of about 400MPa. This value agrees with the tensile strength of some magnesium matrix composites fabricated by liquid infiltration method or powder metallurgy method at the same volume fraction of reinforcements of whisker or particle. Therefore, the melt stirring method which has the advantages of simple process is considered to be efficient in fabricating magnesium matrix composites.

• Polymer(Korea)
• /
• v.29 no.5
• /
• pp.475-480
• /
• 2005

The lowering of melt viscosity has been investigated to achieve the processability enhancement in poly(ethylene naphthalate) (PEN) melt processing by the reactive melt blending with poly(ethylene terephthalate) (PET) and introducing lubricant as well. CaST lubricant resulted in the lowering of PEN melt viscosity but noticeable mechanical property drop was found in PEN with more than $2wt\%$ of lubricant due to the acceleration of thermal degradation by excess lubricant. PEN/PET (90/10) blend has less melt viscosity than PEN and transesterification between two polymers caused the additional viscosity depression. further viscosity lowering was found in PEN/PET blend with CaST since CaST is acting as the catalyst of transesterification as well as a lubricant in PEN/PET blend.

• Polymer(Korea)
• /
• v.29 no.4
• /
• pp.385-391
• /
• 2005

Reactive melt processing has been carried out to investigate crosslinking characteristics of high density polyethylene OTDPE) with dicummyl peroxide (DCP) and perbutyle peroxide (PBP). The increase of torque in the internal mixer indicated that the crosslinking in HDPE has been occurred by peroxides. As a result, the substantial decrease of density, melting temperature, and melt enthalpy were found while the melt viscosity increased in partially crosslinked HDPE. In the mechanical properties of partially crosslinked HDPE, the increase of maximum strength and the decrease in elongation at break were clearly noticed and these were more pronounced when PBP was applied as a crosslinking agent. It seems that the maximum strength was obtained with reactive processing temperature at $150^{circ}C$, however, the mixing time did not affect to the strength of partially crosslinked HDPE.

• Transactions of Materials Processing
• /
• v.18 no.2
• /
• pp.122-127
• /
• 2009

The injection mold with multi-cavity is essential for mass production of plastic products. Multi-cavity molds are designed to geometrically balanced runner system to uniformly fill to each cavity. However, despite geometrical balanced runner system, filling imbalances between cavity to cavity have always been observed in injection molding. To solve these problems, many studies such as Melt Flipper, RC Pin, and others have been presented. The results of these studies have been an effect on filling balances in multi-cavity molds. But, those have had a limitation that additional insert parts must have existed in the mold. In this study, a new runner system is suggested for filling balance between cavity to cavity using "Melt-Buffer" with simple change of runner shape. A series of simulation to confirm feasibility of Melt-Buffer's effects was conducted using injection molding CAE program. Also, a series of injection molding experiment was conducted using plastic materials such as ABS and PP. As results of this study, feasibilities of filling balances by Melt-Buffer were confirmed.

• Transactions of Materials Processing
• /
• v.21 no.2
• /
• pp.107-112
• /
• 2012

Gas-assisted injection molding(GAIM) produces parts with hollow internal sections. The technique offers benefits to powder injection molding(PIM), with lower material usage and reduced time for de-binding processes. In this study, the effects of processing parameters on gas penetration length of gas-assisted powder injection molding(GAPIM) were investigated for SUS316L stainless steel powder feedstock. Experiments were planned based on the Taguchi method, involving processing variables such as melt temperature, shot size, gas pressure, and gas delay time. The most significant parameters affecting gas penetration length were gas delay time and shot size, while the effects of melt temperature and gas pressure was relatively insignificant.

• Resources Recycling
• /
• v.13 no.3
• /
• pp.43-49
• /
• 2004

In this study. an experimental work was performed to mold tensile specimens by using the injection molding machine. Melt temperature, mold temperature and the mixed ratio of recycled resin were selected as processing parameters for studying the effect of those conditions on the shrinkage and weight of molded parts. As a result, the shrinkage was increased with the higher mold and melt temperature and it was more sensitive to the change of mold temperature. On the other hand, the weight of molded parts was decreased with the increment of mold and melt temperature.