• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1025-1029
• /
• 2003

We studied the cross-sectional profiles of deformed thermoplastics in hot embossing process and compared with melt flow index for various embossing conditions such as embossing temperature, embossing pressure and initial thickness of the thermoplastics. The fastest embossing times for complete penetration of the cavities were obtained at temperature greater than $60^{\circ}C$ above glass transition temperature (Tg). When the melt flow index of polymer is low, the penetration ratio does not become large even if the embossing pressure increases. The complete occupation of the cavities was easier obtained with high melt flow index polymer than low melt flow index polymer at the same process condition. We believe these results can be very useful for optimizing nanostructured hot embossing also known nanoimprinting process conditions.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2000.11a
• /
• pp.50-53
• /
• 2000

• Fibers and Polymers
• /
• v.4 no.3
• /
• pp.107-113
• /
• 2003

The branched polypropylene (b-PP) was prepared by melt blending process with initiator, antioxidant, and functional monomers to improve the melt strength through the melt grafting. The melt flow index (MFI) of the b-PP was increased with increasing the initiator content. On the introduction of the alkylamine as the branching agents the MFI of the b-PP was increased, while that of the b-PP with the pentaerythritol triacrylate (PT) was decreased. It may be caused by the chain scission of the i-PP backbone due to the reduced thermal stability of the i-PP on the melt blending. The MFI of the b-PP without the antioxidant was increased due to the chain scission occurred during the melt processing, while on the introduction of the antioxidant, the MFI of the b-PP was decreased. The crystallization temperature of the b-PP was higher than that of PP, which was attributed to the branched chain structure. It was found that the PT was the most effective functional monomers for enhancing the melt properties of the b-PP.

• Korea-Australia Rheology Journal
• /
• v.20 no.2
• /
• pp.79-88
• /
• 2008

In this study, we focus on the improvement of the filling efficiency in injection molding by application of ultrasonic vibration. While studies about the filling efficiency of typical filling processes in the injection molding have been widely performed, there have been only few studies about the filling efficiency of an ultrasonic process. The effect of the ultrasonic vibration is an important process condition, which influences the flow characteristics of polymer melt. This new condition even affects well-known injection conditions such as cavity pressure, injection temperature and mold temperature. For this study, we carried out a numerical analysis by appropriate modeling and analysis of the ultrasonic process in the filling process. To verify this numerical analysis, we compared the numerical results with the experimental data. Also, we analyzed the filling process in a thin cavity using this numerical analysis. To understand the flow characteristics of polymer melt in the ultrasonic process, we substituted real and complex vibration conditions with simplified and classified conditions according to the position of vibrating cavity surfaces and the phase difference between two opposing cavity surfaces. We also introduced MFR (melt flow ratio) as a new index to estimate the filling efficiency in the ultrasonic process.

• Korea-Australia Rheology Journal
• /
• v.21 no.4
• /
• pp.289-297
• /
• 2009

We numerically analyzed flow characteristics of the polymer melt in the screw equipment using a proper modeling and investigated design parameters which have influence on the mixing performance as the capability of the screw equipment. We considered the non-Newtonian and non-isothermal flow in a single rotor equipment to investigate the mixing performance with respect to screw dimensions as shape parameter of the single rotor equipment and screw speed as process parameter. We used Bird-Carreau-Yasuda model as a viscous model of the polymer melt and the particle tracking method to investigate the mixing performance in the screw equipment and considered four mixing performance indexes: residence time distribution, deformation rate, total strain and particle standard deviation as a new mixing performance index. We compared these indexes to determine design parameters and object function. On basis of the analysis results, we carried out the optimal design by using the response surface method and design of experiments. In conclusion, the differences of results between the optimal value and numerical analysis are about 5.0%.

• Elastomers and Composites
• /
• v.48 no.1
• /
• pp.39-45
• /
• 2013

Melt grafting of citraconic acid (CCA) onto an ethylene-propylene-diene terpolymer (EPDM) with various peroxide initiators was performed using a Haake Rheocorder. Finding the optimum running condition and concentration is critical for effective grafting and performance of grafted material. Therefore, this study focused on the effects of mixing (reaction) condition and monomer/initiator dosages on the grafting degree, grafting efficiency and crosslinking degree (gel content), melt flow index and mechanical properties of CCA-g-EPDM. As the grafting degree/crosslinking degrees increased, the tensile strength increased significantly, but elongation at break and melt flow index decreased. The initiator 2,5-dimethyl-2,5-di(tert-butyl peroxy)-hexane (T-101) appeared to meet for the best grafting(2.31%). The grafting degree increased markedly with increasing monomer CCA/initiator T-101 contents. The grafting degree also increased with increasing mixing temperature/time, and then leveled off or decreased/increased a little. The optimum monomer/initiator dosages and reaction temperature/time were found to be about 5/0.05 wt% and $180^{\circ}C$/15min, respectively.

• Elastomers and Composites
• /
• v.42 no.3
• /
• pp.151-158
• /
• 2007

MWNTs have been widely investigated due to unique properties of such as good electrical conductivity and thermal stability in polymer composites industries. This paper established the procedure to fabricate PMMA/MWNT composites by a modular intermeshing co-rotating twin screw extruder with L/D ratio of 42. The electrical properties of PMMA/MWNT composites with different content of MWNT have been investigated. A sheet resistance percolation was observed at 4 wt% of MWNT for the melt processed composites. Sheet resistance of PMMA/MWNT composite film containing 4 wt% of MWNT was nearby $10^4{\Omega}/sq$ and this shows the possibility of potential application to EMI (Electronic Magnetic Interference) shielding materials. The characteristics of composites were analyzed by TGA, DSC, and SEM. In addition, MFI (Melt Flow Index) has been measured to analyze the rheological property.

• Elastomers and Composites
• /
• v.56 no.4
• /
• pp.217-222
• /
• 2021

In this study, random polypropylene (rPP) was compounded with two of monoglycerides, namely, glyceryl monolaurate (GML) and glyceryl monostearate (GMS), as antifogging agents to improve its antifogging performance. rPP film samples were prepared by a film-casting method using a three-roll casting machine after melt blending through a twin screw extruder. With an increase in the monoglyceride content, the melt flow index for rPP films with GML and GMS increased, and their yield strength decreased. The incorporation of GMS in rPP was proven to be more effective in improving its physical properties than was rPP with GML. When GML and GMS were separately added to the rPP film at contents of more than 1 phr and more than 5 phr, respectively, the film exhibited antifogging performance.

• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.261-268
• /
• 2010

Phase change materials based on polypropylene blended with n-eicosane were studied in this paper. In addition, this paper reviews recent studies on the preparation of shape stabilized phase change materials (SSPCM), such as SSPCM from polypropylenes and n-eicosane, their basic properties and possible applications to latent heat storage. The preparation methods used were the melting method and absorption methods. Shape stabilized PCM(SSPCM) prepared for DSC, WAXD, FTIR spectroscopy, ARES, results of the analysis of shape stability heat capacity to improve were identified.

• Korea-Australia Rheology Journal
• /
• v.21 no.1
• /
• pp.17-25
• /
• 2009

We studied the flow characteristics of the polymer melt in the injection molding process with ultrasonic vibration by using the numerical analysis. To minimize the error between the experimental data and numerical result, we presented a methodology using the design of experiments and the response surface method for reverse engineering. This methodology can be applied to various fields to obtain a valid and accurate numerical analysis. Ultrasonic vibration is generally applied between an extruder and the entrance of a mold for improvement the flow rate in injection molding. In comparison with the general ultrasonic process, the mode shape of the mold must be also considered when the ultrasonic vibration is applied on the mold. The mode shape is defined as the periodic and spatial deformation of the structure owing to the effect of the vibration, and it varies greatly according to vibration conditions such as the forcing frequency. Therefore, we considered new index and found the forcing frequency for obtaining the highest flow rate within the range from 20 to 60 kHz on the basis of the index. Ultimately, we presented the methodology for not only obtaining a valid and accurate numerical analysis, but also for finding the forcing frequency to obtain the highest flow rate in injection molding using ultrasonic vibration.