• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.10
• /
• pp.1365-1372
• /
• 2001

In the planar flow casting(PFC) process, the conditions of the melt puddle between nozzle and rotating wheel affect significantly the quality and dimensional uniformity of the downstream ribbon. For stable puddle formation, the nozzle is placed very close to the quenching wheel, so the surface-tension and wall-adhesion forces have an important effect upon the fluid flow.\`In this study the planar flow casting process has been mode]ed using the VOF method for free surface tracking. The transient puddle formation from the present analysis shows good agreements with the previous experimental results. Furthermore, the variation of melt temperature and the corresponding cooling rate of the melt have been examined. The present results also show how the melt puddle can be farmed on the rotating substrate, how the melt flows within the puddle, and how the changes of the process variables affect the puddle formation and its corresponding fluid flow and heat transfer behavior.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.3
• /
• pp.285-295
• /
• 2001

The transport phenomena in a wedge-shaped pool of twin-roll continuous caster are affected by the various operating parameters such as the melt-feed pattern, roll-gap thickness, melt-superheat, and casting speed. A computer program has been developed for analyzing the two-dimensional, steady conservation equations for transport phenomena during twin-roll continuous casting process in order to estimate the turbulent melt-flow, temperature fields, and solidification in the wedge-shaped pool. The turbulent characteristics of the melt-flow were considered using a low-Reynolds-number K-$\xi$ turbulence model. Based on the computer program, the effects of the different melt-feed patterns, roll-gap thicknesses, and superheats of melt on the variations of the velocity and temperature distributions, and the mushy solidification were examined. The results show that the liquidus line is located considerably at the upstream region, and in the lower region appear the well-mixed melt-flow and most widely developed mushy zone. Besides, the variation of melt-flow due to varying melt-feed patterns, affects mainly the liquidus line, and scarcely has effects on the solidus line in the outlet region.

• Journal of the Korean Ceramic Society
• /
• v.42 no.6 s.277
• /
• pp.437-442
• /
• 2005

We fabricated BSCCO-2212 (2212) bulk superconductor by melt casting process, and evaluated the dependence of the critical properties on the temperature and cooling .ate of mold and the pouring methods of melt. It was observed that the critical current (Ic) of 2212 was significantly dependent on the pre-heating temperature of the mold. At the pre-heating temperature of $500^{\circ}C$ followed by air cooling condition, Ic of 48 A at 77 K was obtained which was higher than others processed at different temperatures. In addition, the Ic improved to 132 A when tilt casting method was applied. The improved Ic is probably due to the fact that the tilt casting reduced a turbulent flow of the melt during casting causing less porosity and more homogeneous microsructure. Critical temperature was measured to be 87-89 K after the first heat treatment and it improved to 90-91 K when subsequently heat treated at $650^{\circ}C$ in a nitrogen atmosphere. This improvement was considered to be due to an optimization of the oxygen content in the range of 8.16-8.2.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.6
• /
• pp.579-585
• /
• 2006

We fabricated BSCCO-2212 (2212) rod by the melt casting process (MCP) and evaluated the effect of the melt flowing on the critical current ($I_c$) by using vertical and tilt casting. It was observed that the $2212-SrSO_4$ rod processed by the tilt casting method with homogeneous pre-heating temperature of the mold had a higher $I_c$ than that processed by the vertical casting method. We also evaluated the influence of the strontium sulfates ($SrSO_4$) addition on the texture, microstructure, critical current and temperature, and mechanical hardness of the $2212-SrSO_4$ rods. It was observed that the addition of $SrSO_4$ improved the critical current ($I_c$) and mechanical hardness of the 2212. The $I_c$ of the 2212 increased as the $SrSO_4$ content increased and reached a peak value (260 A at 77 K) at an $SrSO_4$ content of 6 wt.%. In addition, the addition of $SrSO_4$ had a beneficial effect on the mechanical hardness of the 2212. We studied the possible cause of the variation in the $I_c$ with the melt flowing and the $SrSO_4$ content based on the XRD, EPMA analysis and the microstructural observation.

• Journal of Korea Foundry Society
• /
• v.35 no.6
• /
• pp.141-146
• /
• 2015

Aluminum-based hybrid parts were fabricated through a compound casting process with Al or Cu inserts which can be used for applications requiring high conductivity. Because the interface stability between the insert and the aluminum matrix is important, the effects of process variables on the interfacial adhesion strength were investigated. Additions of Cu and Mg to Al melt were found to enhance the adhesion strength, though the melt fluidity was slightly deteriorated when a small amount of Mg was added. An isothermal heating process after casting further improved the strength. However AlCu intermetallic compounds formed and their thickness increased during the heating process. As a result, deterioration in the interfacial adhesion strength was observed after an excessive annealing treatment.

• Journal of Korea Foundry Society
• /
• v.18 no.4
• /
• pp.373-382
• /
• 1998

Particulate reinforced aluminum alloys produced by indirect squeeze casting are difficult to shape by cutting or milling. Therefore near net shape forming of complex shapes is of high economic and technical interest. The complex shape products of $SiC_p/6061$ Al composites are fabricated by the melt-stirring and indirect squeeze casting process. The mold temperatures are $200^{\circ}C$ and $300^{\circ}C$ and applied pressures are 70, 100, and 130 MPa. The volume fractions of the reinforcements are in the range of 5 vol% to 15 vol%. The reinforcement dispersion state are observed using on optical microscope. By employing observed results systematically a correlation is demonstrated among the microstructure, particles behavior, mechanical properties and processing parameters for an optimum melt-stirring(compocasting) and indirect squeeze casting process of MMCs. A procedure to establish the optimum squeeze casting of Al-MMCs is proposed.

• Journal of Korea Foundry Society
• /
• v.23 no.1
• /
• pp.40-46
• /
• 2003

Semisolid forming requires alloys with non-dendritic microstructure of the thixotropy. Recently, low pouring temperture method without stirring, i.e. liquidus casting has been found out new fabrication method of the semisolid metals. Effects of melt superheat and mold conditions on the globulization of primary Al of $AlSi_7Mg$ alloy were investigated in gravity casting process without stirring. The microstructures of primary Al as function of melt superheat and mold temperature show globular, rosette and dendritic shapes. The conditions for globular microstructure of primary Al were low melt superheat < 35 K and low mold temperature < 500 K. The thermal conditions for globular microstructure of primary Al were undercooled melt at early solidification stages and slow cooling < 0.6 K/s. It was found that the initial microstructure was maintained throughout the solidification and the globules of primary Al can be obtained by high nucleation of fine and spherical nuclei due to enhanced undercooling of melt.

• Journal of the Korean Society of Industry Convergence
• /
• v.26 no.5
• /
• pp.945-952
• /
• 2023

In this study, the sand casting process was applied to design the gating system and perform casting simulation in order to domestically produce the submarine mast cover. Based on simulation results, casting experiments were conducted to produce a soundness prototype. The design concept of the mast cover's gating system was based on the design of bell casting. By arranging eight tower-type gates in a circle at 45° intervals, the flow of melt flowing into each gate was uniform and did not mix with each other, and the velocity of melt was also uniform. The mast cover made of Ni-Al-Bronze alloy has no unfilled parts. However, small porosities and flow marks occurred on the surface in several places. Yield strength and ultimate tensile strength are 279.3 MPa and 675.7 MPa, respectively, and elongation is 21.2%.

• Journal of Korea Foundry Society
• /
• v.31 no.5
• /
• pp.274-283
• /
• 2011

The vacuum die casting is a promising candidate of the stamping process for fabrication of fuel cell bipolar plate due to its advantages, such as precision casting, mass production and short production time. This study proposes vacuum die casting process to fabricate bipolar plates in fuel cell. Bipolar plates were fabricated under various injection conditions such as molten metal temperature and injection velocity. Also, according to injection velocity conditions, simulation results of MAGMA soft were compared to the experimental results. In case of melt temperature $650^{\circ}C$, misrun occurred. When the melt temperature was $730^{\circ}C$, mechanical properties were low due to dendrite microstructure. Injection velocity has to set at more than 2.0 m/s to fabricate the sound sample. When melt temperature, injection velocity (Fast shot), and vacuum pressure are $700^{\circ}C$, 2.5 m/s and 30 kPa respectively, sample had good formability and few casting defects. Simulation results are mostly in agreement with experimental results.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.20 no.11
• /
• pp.3474-3490
• /
• 1996

A metal matrix composites(MMCs) for A16061 reinforced with silicon carbide particles is fabricated by melt-stirring method. The primary products of MMCs billets are prepared by volume fractions 5 vol% to 20 vol% and particle size $13\mu m$ to $22\mu m$.This paper will be made to examine the microstructure and mechanical properties of fabricated $SiC_p$/Al 6061 composite by melt-stirring and squeeze casting method. The MMC billets is extruded at $500^{\circ}C$ under the constant extrusion velocity $V_e$=2mm/min using curved shape die. Extrusion force, particle rearrangement, micro structure and mechanical properties of extruded composites will be investigated. The mechanical properties of primary billets manufactured by melt-stirring and squeeze casting method will be compared with extrusion specimen. The effect of volume fraction and size of the reinforcements will be studied. The increase in uniformity of particle dispersion is the major reason for an improvement in reliability due to hot extrusion with optimal shape die. Experimental Young's modulus and 0.2% offset yield strength for the extruded MMCs will be compared with theretical values calculated by the Eshelby method. A method will be proposed for the prediction of Young's modulus and yield strength in $SiC_p$ reinforced MMCs.