• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.399-403
• /
• 2007

Trans-esterification behavior of polycarbonate/poly(butylene terephthalate) (PC/PBT) blends was investigated during the melt mixing process. Rheological and fracture behaviors, and fracture morphology were also investigated as a function of PC/PBT blend ratio. Based on FT-IR and $^1H-NMR$ results, a trans-esterification reaction was confirmed to occur between PC and PBT during the melt mixing process. The melt index(MI) decreased with increased PC content, indicating the higher flow resistance of PC. The storage and loss moduli were increased by increasing the PC loading, and the PC/PBT blends were rheologically incompatible based on the Cole-Cole plot. The tensile property increased linearly with the increased PC content. However, the impact strength increased until 50 wt% of PC loading, notably around $30{\sim}40wt%$, and then was levelled off at 50 wt%. Rough ridges were formed on the impact fracture surfaces above the 40 wt% of PC content, supporting the observed higher impact strength in this range.

• Korea-Australia Rheology Journal
• /
• v.11 no.3
• /
• pp.255-263
• /
• 1999

Blends of two thermotropic liquid crystalline polymers, HX2000 and Vectra A950, were prepared by melt blending. Effects of transesterification on these blends are investigated by comparing properties of the blends with and without the addition of an inhibitor, in terms of blend miscibility and rheology. Both the uninhibited and inhibited blends are found to be largely immiscible with very limited miscibility in HX2000-rich phase. No strong evidence indicates the occurrence of transesterification in the blends in the solid state. Dynamic rheological behaviour, such as shear storage modulus (G') and shear loss modulus (G") as a function of frequency, of the blends are interpreted by a three-zone model. HX2000 shows terminal-zone and plateau-zone behaviour, whilst Vectra A950 shows plateau-zone and transition-zone behaviour. The un- inhibited blends show plateau-zone behaviour up to 50% Vectra A950 content and the inhibited blends show plateau-zone behaviour up to 60% Vectra A950 content. Compositional dependence of the complex viscosities of the uninhibited and inhibited blends displayed positive deviations from additivity, which is a characteristic feature for the immiscible thermoplastic blends. When under steady shear, both the uninhibited and inhibited blends show shear thinning behaviour and their viscosities decrease monotonically with the addition of Vectra A950. Compositional dependence of the steady shear viscosities of the two sets of blends displayed negative deviations from additivity and the uninhibited blends were more viscous than the inhibited blends for the full composition range. Although limited agreement with the Cox-Merz rule is found for the inhibited blends, these two sets of blends, in general, do not follow the rule due to their liquid crystalline order and two-phase morphology. Despite being immiscible blends, transesterification, such as polymerization, in the blends might occur during the rheological characterization, supported by the facts that uninhibited blends show HX2000-dominant behaviour at lower Vectra A950 content and are more viscous than the inhibited blends. The addition of transesterification inhibitor in such blends is advised if only physical mixing is desired.ired.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.5
• /
• pp.1125-1129
• /
• 2008

Polypropylene (PP)/corn starch master batch(starch-MB) blends with different PP compositions of 90, 80, 70, and 60 wt% were prepared by melt compounding at $200^{\circ}C$, using lab scale Brabender mixer. The chemical structures, thermal properties and non-isothermal crystallization behavior of the PP/starch-MB blends were investigated by FT-infrared spectrometry (FT-IR), differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). The fabrication of the PP/starch-MB blend was confirmed by the existence of hydroxy group in FT-IR spectrum. There was no district change in melting temperature and melting enthalpy, and TGA curve indicates a decrease in degradation temperature with starch-MB content. The non-isothermal crystallization process was analyzed using by Avrami equation. The Avrami exponents were in the range of 2.71-3.97 for PP and 1.48-1.99 for PP/starch-MB blonds. The activation energies calculated by Kissinger method were 233 kJ/mol for PP, 484 kJ/mol for PP90, 541 kJ/mol for PP80, 553 kJ/mol for PP70, and 422 kJ/mol for PP60.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.820-828
• /
• 2000

In this study, biaxially oriented film process was used to improve barrier property of polypropylene (PP)/ethylene-vinyl alcohol copolymer (EVOH) blends by inducing a laminar morphology of the dispersed phase in the matrix phase. In order to examine the extent of deformation during melt extrusion process, the rheological properties of the resins were measured and the viscosity ratio of the dispersed phase to the continuous phase was determined. The effects of compatibilizer content, draw ratio, and draw temperature on the oxygen permeability and morphology of biaxially drawn blend films were studied. The laminar morphology of the EVOH phase with a larger area of thinner layer induced by biaxial orientation was found to result in a significant increase in oxygen barrier property of PP/EVOH (85/15) blends by about 10 times relative to the pure PP When both PP-g-MAH and ionomer were used as the compatibilizers, there existed an optimum level of compatibilizer content for obtaining improved barrier properties with a well developed laminar structure. In addition, higher draw ratio and draw temperature were found to be more favorable processing conditions in obtaining higher barrier blends.

• Applied Chemistry for Engineering
• /
• v.10 no.8
• /
• pp.1141-1146
• /
• 1999

Melt blend of PA6/PP-g-MA system containing SEBS-g-MA as a compatible impact modifier was prepared to investigate the change of mechanical properties and morphologies. The tensile strength slightly decreased, but the elongation at break increased with increasing content of SEBS-g-MA in the blend. Also the notched izod impact strength increased with increasing the content of PP-g-MA and SEBS-g-MA. It is attributed to improved compatibilization and interfacial adhesion by reaction of the amide of PA6 with maleic anhydride of SEBS-g-MA and PP-g-MA. The result of dynamic mechanical analysis(DMA) showed a typical behavior of the compatibilization in the polymer blends. Finally, in the phase structure observed by the use of SEM, we confirmed improvement of the compatibilization and interfacial adhesion with increasing the content of SEBS-g-MA and PP-g-MA.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.37-44
• /
• 2002

The polymer blends of waste polyvinyl chloride (RPVC) and waste polyethylene(RPE) were prepared by melt mixing, and their morphology and tensile properties were evaluated after the copolymers having an ethylene group in backbone and ester group in side position were added as comptatibilizers. The blend compositions were varied as follows ; RPVC/RPE 85/15 wt%, where RPVC formed a continuous phase : 50/50, mid composition : 15/85, RPE a continuous phase. The blends revealed a very low compatibility between component polymers because they showed domain sizes greater than $10\mu\textrm{m}$ over all compositions, especially the worst compatibility around mid composition. The blends showed higher compatibility when ethylene vinylacetate copolymer(EVA) and ethylene ethylacrylate-graft-methyl methacrylate copolymers(EEA-MMA) were added.

• Polymer(Korea)
• /
• v.28 no.6
• /
• pp.468-477
• /
• 2004

The polymer blends of waste poly(vinyl chloride) (RPVC) and waste polyethylene (RPE) were prepared by melt mixing. Various ethylene-vinyl acetate copolymers (EVA) and ethylene-methacrylic acid Na salt copolymer (ionomer) were used as compatibilizer. Their morphologies and mechanical properties were evaluated as a funtion of mixing sequence and time. EVA with high vinyl acetate contents showed a rapid increment of tensile properties when small amount was added. Tensile properties of the blends were gradually increased with the addition of ionomer. Morphologies of RPVC/RPE blends were analyzed by scanning electron microscopy. FT-IR data showed that EVA was a good compatibilizer in RPVC/RPE blend compared to ionomer. Mechanical properties of the blends were highly enhanced when RPVC and compatibilizer were mixed and first RPE was added later.

• Textile Coloration and Finishing
• /
• v.35 no.3
• /
• pp.159-168
• /
• 2023

Polyolefin elastomer (POE) is widely used in a variety of applications, particularly in the manufacture of composites, due to its excellent mechanical properties, chemical resistance, and flexibility. However, POE has a high processing temperature, which causes damage to the fiber during the manufacturing process when impregnating the fiber. Therefore, ethylene vinylacetate (EVA), which has a low melting point and excellent adhesion properties, is blended with POE to reduce the processing temperature, and POE-g-MAH (Polyolefin elastomer-grafted-maleic anhydride) is used as a compatibilizer to further improve the POE/EVA blend properties. The compatibility of POE/EVA blends is observed by SEM, and the interaction between each polymer is confirmed by DSC and FT-IR. In addition, the effect of adding the compatibilizer is analyzed through mechanical properties such as tensile strength and elongation. The optimal content of compatibilizer for POE/EVA blends considering physical properties and moldability is sought, and 20 phr is determined to be the most appropriate.

• Polymer(Korea)
• /
• v.24 no.5
• /
• pp.664-672
• /
• 2000

It is generally agreed that transesterification provides the, copolymer in the melt blending of poly(ethylene naphthalate) (PEN) and poly($\varepsilon$-caprolactone) (PCL). Effects of the conditions of transesterification reaction and catalyst on the degree of randomness and average sequence length of PEN/PCL blends were investigated and results were used to interpret the biodegradability of PEN/PCL blends. It was found that degree of randomness values of obtained copolymer lied between 0 and 1, and it indicated that this blend consisted with physical blends of PEN/PCL and PEN/PCL block copolymers. The degree of randomness reached almost 1 which is the theoretical value of random copolymers and the average sequence length became shorter by the further transesterification reaction. In additions, it was found that the increase of copolymers, especially random copolymers reduced the biodegradability in PEN/PCL blends.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.557-561
• /
• 2007

Polypropylene (PP)/corn starch master batch (starch-MB) blends with different PP compositions of 40, 50, 60, and 80 wt% were prepared by melt compounding at $200^{\circ}C$, using lab scale Brabender mixer. The chemical structures and thermal properties of the PP/starch-MB blends were investigated by FT-IR, differential scanning calorimetry (DSC), and thermogravimetric analyzer (TGA). The chemical structure was confirmed by the existence of hydroxy group. There was no district change in melting temperature and melting enthalpy, and TGA curve indicated a decrease in degradation temperature with starch-MB content. The porosity change of blend was measured by scanning electron microscope (SEM), the degree of porosity on the blend surface increased with the starch-MB content. The rheological properties indicated an increase in complex viscosity, shear thinning tendency and elasticity with the starch-MB concentration. These effects were confirmed by an oscillatory viscometer at $200^{\circ}C$. From these results, it is found that 40 wt% is the optimum starch-MB concentration. The fiber was fabricated from PP60/MB40 with 40 wt% starch-MB and the porosity and tensile properties were investigated.