• Fibers and Polymers
• /
• v.7 no.2
• /
• pp.95-104
• /
• 2006

In order to improve the water swelling, thermal/mechanical and adhesion properties of waterborne polyurethane (WBPU), a series of the crosslinkable WBPUs containing hydrophilic ionic component, dimethylol propionic acid (20 mole%), were prepared by in-situ polymerization using a cross-linker hexakis (methoxymethyl) melamine (HMMM). Effects of the HMMM content (2, 4, and 6 wt%) and curing temperature on these properties of the crosslinked WBPUs samples were investigated. All properties were found to increase with increasing HMMM content. It was found that the optimum curing temperature of the WBPU films and adhesives was near $120^{\circ}C$, which was not dependent on the HMMM content.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.11 no.1
• /
• pp.51-62
• /
• 1987

In this study, electrostatic behavior of polyester and nylon fabric treated with anti-static agents were investigated. The effects of the concentration of the agents and curing conditions on the electrostatic charge of the fabrics were studied. And washfastness, lightfastness and physicalproperties of the treated fabrics were also investigated. The results were as follows: 1) Polyethylene glycol alkylester was more effective in antistatic behavior than polyethylene laurylphosphate, and polyester is more effective in anti-static behavior than nylon. 2) Concentration of anti-static agents were suitable in concentration of $4\%$. 3) Glyoxal resin was more effective in anti-static behavior than melamine resin, and it was also good in the retaing anti-static behavior after treatments of lightfastness and washfastness. 4) As the condition of curing treatment, $190^{\circ}C$, 1min. for glyoxal resin and $130^{\circ}C$, 4min. for melamine resin is appropriate. 5) In comparison of anti-static behavior according to treating conditions, the simultaneous treatment was more effective than any other treatments. 6) Change of electrostatic charge of anti-static nylon cloths after treatments of lightfastness and washfastness increased greatly in above 10 laundering time and 20 fade-O-meter time. 7) In physical properties according to concentration of treating agents. decrease of physical properties scarcely appeared in concentration of treating agents $4\~5\%$.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.682-690
• /
• 2015

The bonding performance of two types of wood adhesives, namely phenol-resorcinol-formaldehyde (PRF) resin and melamine-urea-formaldehyde (MUF) resin for glued laminated timber manufactured by high frequency (HF) heating was evaluated. The HF heating system consists of HF oscillator with dielectric heating system for curing adhesives, and hydraulic press system for clamping glued laminated timber. The designed frequency and output power of the HF system was as 5 MHz and 60 kW, respectively. To verify dielectric heating mechanism under HF oscillation, the heat loss factors of laminae and adhesives were measured. The results show that it is possible to selectively heat adhesives for their curing due to the remarkably higher loss factor of the adhesives than those of wood laminae. The temperature of adhesive in the bonding line reached up to the set temperature within a few seconds by high frequency oscillating, which advanced the curing of adhesive afterwards. The bonding performance, such as shear strength of bonding line, water soaking delamination, and boiling water soaking delamination of PRF resin met the requirement of Korean Standard (KS), however the MUF resin did not meet the KS requirement of boiling water soaking delamination. These results indicate that the HF heating system is successful to manufacture glued laminated timbers with PRF resins to meet the bonding requirements.

• Journal of the Korean Applied Science and Technology
• /
• v.26 no.1
• /
• pp.18-23
• /
• 2009

Curing behavior and structural property of an inorganic compound added urea-formaldehyde(UF) and urea-melamine-formaldehyde(UMF) were studied. In addition, tensile strength and formaldehyde emission of plywoods made of those resin binders were studied. Curing temperature and structure were not changed, but tensile strengths of plywoods manufactured both with a UF resin and a UMF resin were decreased slightly as increased amount of inorganic compound. Formaldehyde emissions from plywoods were reduced as increased amount of inorganic compound. Wheat flour as an extender was helped to reduce of formaldehyde emission. From the result of this study it might be estimated that using appropriate amount of inorganic compound and proper resin system can be strengthened bond strength and reduced formaldehyde emission.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.5
• /
• pp.42-48
• /
• 2008

This study was conducted to discuss the effects of hardener and extender contents on peak temperature, reaction enthalpy (${\Delta}H$), gelation time, viscosity change, and pH value in three types of UMF (urea-melamine- formaldehyde) resin with the help of perpHecT LogR meter, differential scanning calorimetry (DSC), and advanced rheometric expansion system (ARES), The results indicated that the pH value of Control A steeply decreased to 5,2 in the early stage but relatively remained constant thereafter as in Synthesis 1 and Synthesis 2, The peak temperature and time decreased as well, whereas ${\Delta}H$ and viscosity increased with the increase of hardener content. On the other hand, ${\Delta}H$ was not changed up to the extender content of 5% and then decreased with its further addition, And the pH value and peak temperature showed no change with the increase of extender content at the hardener content of 5% in three types of UMF resin, The effect of hardener content in this experiment, however, appeared more conspicuous in Control A than in the other two types of Synthesis 1 and Synthesis 2, These results might be caused by higher molecular weight with longer chains of methylene ($-CH_2-$) and methylene ($-CH_2-O-CH_2-$) ether bridges or much more branched chains in Control A.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.200-209
• /
• 2019

To improve the water resistance of melamine-urea-formaldehyde (MUF) resins, different levels of blocked polymeric 4,4 diphenyl methane diisocyanate (B-pMDI) were blended with MUF resins to prepare B-pMDI/MUF hybrid adhesives, and their adhesion performances were evaluated for the surface lamination of fancy veneer on plywood. FT-IR spectra showed that the de-blocked -NCO groups reacted with the -OH of hydroxymethyl groups of the MUF resins to form urethane bonds at 2% B-pMDI/MUF, which was detected before and after their hydrolysis. The mass loss after the hydrolysis consistently decreased as the B-pMDI level increased, indicating an improvement in the water resistance. As the B-pMDI level increased, the activation energy of hybrid adhesives decreased, which improved the reactivity of the hybrid adhesives. Additionally, the water resistance improvement of the hybrid adhesives increased the tensile shear strength of the surface laminated plywood in semi-water proof and water-proof by 23 % and 8 %, respectively, at 2% B-pMDI level. This was likely due to the urethane linkages in the hybrid adhesives. However, the formaldehyde emission from plywood panels bonded with the hybrid adhesives increased in the dry state, indicating incomplete curing of the hybrid adhesives.

• Journal of Adhesion and Interface
• /
• v.12 no.4
• /
• pp.105-110
• /
• 2011

Polyester/melamine cured coatings had been used for pre-primed coatings and pre-coated metal coatings, because it has good mechanical,chemical properties, and mar resistance. But it has weak points such as stiffness and low formability for making automotive components. Polyester had been synthesized using polycarbonate diol of long alkyl chain which can improve flexibility and formability which is one of the important factors for pre-coated steel sheets (PCM). In this study, strain and tensile strength were examined by the tensile test and formability was examined by the drawing test. Also, Those polyester resins were also measured by DMA to verify flexibility of cured coatings.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.37-45
• /
• 2006

The viscoelastic properties of blends of melamine-formaldehyde (MF) resin and poly(vinyl acetate) (PVAc) for engineered flooring used on the Korean traditional ONDOL house floor heating system were investigated by dynamic mechanical thermal analysis (DMTA). Because MF resin is a thermosetting adhesive, the effect of MF rein was shown across all thermal behaviors. The addition of PVAc reduced the curing temperature. The DMTA thermogram of MF resin showed that the storage modulus (E') increased as the temperature was further increased as a result of the cross-linking induced by the curing reaction of the resin. The storage modulus (E') of MF resin increased both as a function of increasing temperature and with increasing heating rate. From isothermal DMTA results, peak $T_{tan{\delta}}$ values, maximum value of loss modulus (E") and the rigidities (${\Delta}E$) of MF/PVAc blends at room temperature as a function of open time, peak $T_{tan{\delta}}$ and maximum loss modulus (E") values were found to increase with blend MF content. Moreover, the rigidities of the 70:30 and 50:50 MF/PVAc blends were higher than those of the other blends, especially of 100% PVAc or MF. We concluded that blends the MF/PVAc blend ratios correlate during the adhesion process.

• Textile Coloration and Finishing
• /
• v.23 no.2
• /
• pp.107-117
• /
• 2011

Polyurethane (PU) was synthesized by one-shot process and the PU nanofiber was prepared by electrospinning. In this study, electrospun PU multi-membranes were prepared with various coating thickness ratio of base resin to top resin, where the base resin contains melamine curing agent and acid catalyst and the top resin contains water-repellent agent of fluoro-carbon compounds. The PU nanofiber multi-membranes were analyzed by field-emission scanning electron microscopy, differential scanning calorimeter, breathability, tensile strenth, air permeability and water resistance. The results showed that the PU multi-membrane provided excellent waterproof and moisture permeability.

• Elastomers and Composites
• /
• v.26 no.3
• /
• pp.193-201
• /
• 1991

Epoxy resin and CTBN(carboxyl terminated butadiene acrylonitrile) rubber were reacted at $150^{\circ}C$. Epoxy mixtures containing reactant in a ratio $0{\sim}75%(wt%)$ of total liquid component were with dicyandiamide(DICY) at $130{\sim}200^{\circ}C$. Cure, thermal and adhesive properties were investigated in relation to rubber content, cure temperature, hardner content and promoter content. $CTBN{\times}13$ showed better properties in miscibility, curing time and adhesive strength. 2PZ-CNS was more excellent in Tg, and melamine was in adhesive strength. Adhesive strength represented best at rubber content $12{\times}15%$.