• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.676-683
• /
• 2000

For high quality storage of agricultural products, temperature, humidity and gas conditions in a storage house should be controlled properly. But most of the low temperature storage house is depending on temperature control. This study aimed to develop an automatic control system for low temperature storage house that can control storage conditions such as temperature, humidity and $CO_2$ gas concentration. The developed system alarms the user, by telephone or beeper, when abnormal condition has occurred. The farmer can also monitor the inside condition of warehouse in his residence, by Internet. From the results of the performance test, the temperature and relative humidity in the warehouse is controlled within the range of ${\pm}0.5^{circ}C$ and ${\pm}2%$, respectively.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 1996년도 International Conference on Agricultural Machinery Engineering Proceedings
• /
• pp.1055-1062
• /
• 1996

A method for automatically driving paddy vehicles, such as rice transplanters, etc., straight ahead in a paddy field was investigated . The direction of such vehicles must be precisely controlled to do the operations as straight. However, the alignment of the from wheels becomes distorted due to the unevenness of the ground, preventing the vehicle form going straight. If the proper alignment of the front wheels is maintained , the vehicle can be driven straight ahead greater precision. To investigate the influence of the ground uneveness, the behavior of a paddy vehicle running over an obstacle was quantified. The left wheel ran over an obstacle on a flat concrete road surfaced. When the steering wheel was free, the front wheels were forced toward the left when vehicle went up the obstacle and toward the right when the vehicle went down it. The torsion of the wheel when the vehicle went down the obstacle was larger than that when it went up ,so it turned right 5 degrees. Sinc hydraulic control steering decreased the steering angle , it turned right 3 degrees. These results suggest that a vehicle can be driven straight ahead with high precision when the steering angle is changed in response to the direction and inclination of the vehicle . Such results were obtained in a paddy field tests.

• Journal of Biosystems Engineering
• /
• 제27권5호
• /
• pp.417-424
• /
• 2002

This study was conducted to develop a vehicle, leading or following a worker at a certain distance to assist laborious transporting works in greenhouses. A prototype vehicle was tested in the practical field conditions using a developed control algorithm. Results of this study were summarized as following: 1. The sensing device consisted of infrared sensors was attached to the front of the vehicle and turning following algorithm was developed to make the vehicle turned as it follows a worker simultaneously. 2. The measured average power consumptions were 110W and 89W, equivalent to 5.2-6.4 hrs battery durations, at low speed with and without the maximum payload, respectively. 3. Results of the travel tests showed that the deviations from the center of row spacing were $\pm$100 mm along the ridge and $\pm$85 mm along the hydroponic bed in the greenhouse. Therefore, the worker-following transport vehicle was feasible to travel along the row without collision in the greenhouse.

• Journal of Biosystems Engineering
• /
• 제27권5호
• /
• pp.409-416
• /
• 2002

This study was conducted to develop a vehicle, leading or following a worker at a certain distance to assist laborious transporting works in greenhouses. A prototype vehicle, which consisted of the rear driving, the front steering and the console units, was designed and tested in the ideal indoor conditions. Results of this study were summarized as following: 1. The driving unit was designed to travel at the speed ranges of 0.3∼0.8 m/sec depending on the operating modes with a maximum payload of 100 kg. 2. The console unit consisted of a main-board including a 80C196KC microprocessor and peripheral devices, a power-board and safety interlock. Worker-leading, and following modes were available in automatic and manual modes. 3. Steering was achieved by turning the steering motor against the sensed direction. Proper steering angles for correcting travel direction were determined as 5 and 9 degrees when sensing cultivation beds and plants, respectively.

• Journal of Biosystems Engineering
• /
• 제25권5호
• /
• pp.385-390
• /
• 2000

The heat pump is one of heating and cooling systems driven by electricity using natural energy as a heat source. The heat pump system was mainly adopted to a cooling system or a refrigeration system. In regions with a large amount of electricity, it is used as a heating system or a heating and cooling system of houses, buildings and agricultural facilities. During cold weather, air source heat pumps do not work well because of some technical problems, such as frosting on evaporator coil when outside air temperature is below -5$^{\circ}C$. In this research, the heat regenerative technology was employed to eliminate the frosting on evaporator coil and improve the COP of the heat pump system. This fiber belt heat regeneration system(FBHRS) has very simple structure consisting of a geared motor and a porous fiber belt passing through alternatively between cold and warm air duct. The laboratory test showed that the heat pump system with a FBHRS yielded an impressive COP higher than 3.5 at the outside air temperature of -7$^{\circ}C$ in heating mode.

• 드라이브 ㆍ 컨트롤
• /
• 제16권4호
• /
• pp.74-79
• /
• 2019

In this study, an edible fresh corn harvest testing machine was designed and manufactured. And harvesting performance was analyzed through the field test. The testing machine is of the tractor attached type. It is connected to the tractor PTO shaft to transfer power to the each part of the harvesting machine. And it harvests fresh corn by one row through the processes of cutting, stem crushing, detaching, and collecting. The performance test was performed at PTO speed (540, 750, 1050 rpm, respectively), working speed (0.1, 0.15, 0.2 m/s, respectively), and cropping cultivation (row spacing·hill spacing 70·25 cm, 70·40 cm, 90·30 cm, respectively). The performance test was repeated three times in the 15 m section. The detachment loss ratio, uncollected crop ratio, damage ratio, and harvest ratio were analyzed. As a result of the performance test, it was analyzed that the PTO speed 540 rpm, running speed of 0.1 m/s, and row spacing·hill spacing 70·40 cm were the optimal condition.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.III
• /
• pp.698-706
• /
• 2000

It is very difficult to mechanize tomato harvesting because identifying a tomato partly covered with leaves and stalks is not easy. This research was conducted to develop tomato harvesting robot which can identify a target tomato, determine its three dimensional position, and harvest it in a limited time. Followings were major findings in this study. The first visual system of the harvesting robot was composed of two CCD cameras, however, this could not detect tomatoes which are not seen on the view finder of the camera especially those partly covered by leaves or stalks. The second visual device, combined with two CCD cameras and pan/tilt procedures was designed to minimize the positioning errors within ${\pm}10mm$, but this is still not enough to detect tomatoes partly covered with leaves etc. Finally, laser distance detector was added to the visual system that could reduce the position detecting errors within 10mm in X-Y direction and 5mm in Z direction for the partly covered tomatoes.

• Journal of Biosystems Engineering
• /
• 제28권3호
• /
• pp.245-252
• /
• 2003

This study was investigated the possibility of measuring chlorophyll in paddy crops using two kinds of chlorophyll meters(SPAD-502, Field Scout). The results of correlation analysis showed the 0.7758(r$^2$) relationship between the chlorophyll contents of paddy leaves measured by SPAD and spectrophotometer. It indicates that chlorophyll content in paddy crops could be measured using the SPAD. Considering the data of the SPAD and Field Scout there was significant difference between their chlorophyll contents measured by the SPAD and Field Scout. Likewise, such results were consistent with the corrected data using light intensity. According to the results, it can be concluded that it is difficult to describe the rice chlorophyll measured by the Field Scout more accurately than the SPAD when using one standard spectrum and another spectrum for reflectance measuring. The chlorophyll variance measured at a research institute and a farmer's field revealed that the output of SPAD was more reliable than that of the Field Scout.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.307-312
• /
• 2000

This study was carried out to develop an automatic grafting system suitable for fruit-vegetable seedlings. The study consisted of two research sections: 1) development of a medium-sized, low-cost automatic grafting system for cooperative farms and commercial seedlings production company, and 2) commercializing research for prototype development based on the above concepts. The grafting robot developed in this research can be described as follows, a. Developed grafting robot can cover the whole operations for grafting scion and rootstock, only if operator provides scion and rootstock tray. b. Five seedlings can be grafted at one time, and about 1,200 seedlings can be grafted in one hour. c. The success ratio of mechanical grafting scion and rootstock with ceramic pin bonding provided by the holder is more than 95% when the conditions of seedlings are satisfied. d. The grafting efficiency has improved over 10 times compared with manual work, and the grafting cost generated 44% savings.

• Agricultural and Biosystems Engineering
• /
• 제2권1호
• /
• pp.31-36
• /
• 2001

Based on the viscous flow characteristics of gas through capillary tube, a simple and cheap gas mixing system was developed for controlling gas compositions in CA chambers. The gas flow rate through capillary tube had a linear relationship with pressure, (length)$^{-1}$ and (radius)$^4$ of capillary tube, which agreed well with Hagen-Poiseuille’s law. The relationship between flow rate and combined parameters was described as Q=0.000209724($\pi$ r$^4$P/$\mu$L) and the coefficient of determination was 0.9984. The developed system could control gas concentrations in CA chambers within $\pm$0.3% deviation compared to the preset concentrations. It was possible to predict the required time and required gas flow rate for exchanging the gs in CA chamber to a certain concentration of gas by using the mathematical model developed in this study.