• 한국정밀공학회지
• /
• 제23권5호
• /
• pp.155-161
• /
• 2006

This paper introduces a new type of mechanical tape feeder for chip mounter. The mechanical feeder is composed of a pneumatic linear actuator and a linear feeding module with the application of a cam-slider. As semiconductor chips are getting smaller, PCB assembly makers require the feeder to position the chip with high accuracy. The linear feeding system improves the positioning accuracy of the chip by getting rid of the index error, which brings into existence on the sprocket rotating feeder. It also can make greatly reduce the dumping rate. The dumping error is caused by the impact occurred as the pawl to interrupt ratchet wheel rotation. The paper discusses its mechanism and mechanical performance. The positioning accuracy and the dynamic characteristic were measured for long time operation and analyzed. As a result, the feeder showed very good performance. However, the feeding system was dynamically unstable due to the cover film eliminator that is required to be modified

• Journal of Positioning, Navigation, and Timing
• /
• 제7권4호
• /
• pp.277-284
• /
• 2018

The Satellite-based Augmentation System (SBAS), as a safety critical system, should be verified on an ongoing basis to ensure the adequate performance. This study proposes two methods to evaluate the performance of SBAS satellite correction. Analysis methods based on precise ephemeris and measurement were applied to present an evaluation method for SBAS satellite correction, and a test was performed based on real data. The precise ephemeris-based analysis method had no limitations on the position of the test user and showed a high precision, enabling an accurate performance analysis in various positions. Although the measurement-based analysis method has the advantage of fast data interval, it showed a relatively lower accuracy due to the effects of various error factors. Compared with the precise ephemeris-based analysis method, there was a large difference of more than 5 m at the beginning of smoothing filter, and a difference less than 50 cm when filtered for more than an hour.

• Journal of Positioning, Navigation, and Timing
• /
• 제8권2호
• /
• pp.59-68
• /
• 2019

This paper proposed a method to estimate the vertical delay from the slant delay, which can improve accuracy of the ionospheric correction of SBAS. Proposed method used Chapman profile which is a model for the vertical electron density distribution of the ionosphere. In the proposed method, we assumed that parameters of Chapman profile are given and the vertical ionospheric can be modeled with linear function. We also divided ionosphere into multi-layer. For the verification, we converted slant ionospheric delays to vertical ionospheric delays by using the proposed method and generated the ionospheric correction of SBAS with vertical delays. We used International Reference Ionosphere (IRI) model for the simulation to verification. As a result, the accuracy of ionospheric correction from proposed method has been improved for 17.3% in daytime, 10.2% in evening, 2.1% in nighttime, compared with correction from thin shell model. Finally, we verified the method in the SBAS user domain, by comparing slant ionospheric delays of users. Using the proposed method, root mean square value of slant delay error decreased for 23.6% and max error value decreased for 27.2%.

• Journal of Positioning, Navigation, and Timing
• /
• 제11권4호
• /
• pp.369-379
• /
• 2022

In weighted k-nearest neighbor (WkNN)-based Fingerprinting positioning step, a process of comparing the requested positioning signal with signal information for each reference point stored in the fingerprint DB is performed. At this time, the higher the number of matched base station identifiers, the higher the possibility that the terminal exists in the corresponding location, and in fact, an additional weight is added to the location in proportion to the number of matching base stations. On the other hand, if the matching number of base stations is small, the selected candidate reference point has high dependence on the similarity value of the signal. But one problem arises here. The positioning signal can be compared with the repeater signal in the signal information stored on the DB, and the corresponding reference point can be selected as a candidate location. The selected reference point is likely to be an outlier, and if a certain weight is applied to the corresponding location, the error of the estimated location information increases. In order to solve this problem, this paper proposes a WkNN technique including an outlier removal function. To this end, it is first determined whether the repeater signal is included in the DB information of the matched base station. If the reference point for the repeater signal is selected as the candidate position, the reference position corresponding to the outlier is removed based on the clustering technique. The performance of the proposed technique is verified through data acquired in Seocho 1 and 2 dongs in Seoul.

• Journal of Positioning, Navigation, and Timing
• /
• 제7권4호
• /
• pp.295-305
• /
• 2018

Network RTK is a highly practical technology that can provide high positioning accuracy at levels between cm~dm regardless of user location in the network by extending the available range of RTK using reference station network. In particular, unlike other carrier-based positioning techniques such as PPP, users are able to acquire high-accuracy positions within a short initialization time of a few or tens of seconds, which increases its value as a future navigation system. However, corrections must be continuously received to maintain a high level of positioning accuracy, and when a time delay of more than 30 seconds occurs, the accuracy may be reduced to the code-based positioning level of meters. In case of SSR, which is currently in the process of standardization for PPP service, the corrections by each error source are transmitted in different transmission intervals, and the rate of change of each correction is transmitted together to compensate the time delay. Using these features of SSR correction is expected to reduce the performance degradation even if users do not receive the network RTK corrections for more than 30 seconds. In this paper, the simulation data were generated from 5 domestic reference stations in Gunwi, Yeongdoek, Daegu, Gimcheon, and Yecheon, and the network RTK and SSR corrections were generated for the corresponding data and applied to the simulation data from Cheongsong reference station, assumed as the user. As a result of the experiment assuming 30 seconds of missing data, the positioning performance compensating for time delay by SSR was analyzed to be horizontal RMS (about 5 cm) and vertical RMS (about 8 cm), and the 95% error was 8.7 cm horizontal and 1cm vertical. This is a significant amount when compared to the horizontal and vertical RMS of 0.3 cm and 0.6 cm, respectively, for Network RTK without time delay for the same data, but is considerably smaller compared to the 0.5 ~ 1 m accuracy level of DGPS or SBAS. Therefore, maintaining Network RTK mode using SSR rather than switching to code-based DGPS or SBAS mode due to failure to receive the network RTK corrections for 30 seconds is considered to be favorable in terms of maintaining position accuracy and recovering performance by quickly resolving the integer ambiguity when the communication channel is recovered.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 Proceedings of the Korea Automatic Control Conference, 11th (KACC); Pohang, Korea; 24-26 Oct. 1996
• /
• pp.385-388
• /
• 1996

A time delay controller with state feedback is proposed for azimuth motion control of the frictionless positioning device which is subject to the variations of inertia in the presence of measurement noise. The time delay controller, which is combined with a low-pass filter to attenuate the effect of measurement noise, ensures the asymptotic stability of the closed loop system. It is found that the low-pass filter tends to increase the robustness in the design of time delay controller as well as the gain and phase margins of the closed loop system. Numerical and experimental results support that the proposed controller guarantees a good tracking performance irrespective of the variation of inertia and the presence of measurement noise.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 학술대회 논문집 정보 및 제어부문
• /
• pp.465-467
• /
• 2004

This paper deals with the design and analysis of automatic virus infection machine, which can be used in blood testing at veterinary hospital. It consists of the mechanical positioning parts and electrical control parts. Two of driving motor and ball screws are used to move the liquid container into the test position and mix the blood on litmus paper. In addition, a thermal controller is installed to keep the container temperature on constant level. The user interface using with a LCD and some keys are supplied with a 8-bit single chip controller. All of the designs issue related with the mechanism and controllers are discussed in detail. Finally the proposed machine is tested in real experiment with the formal processing to judge the virus infection, and also the usefulness of designed algorithm is verified through the experiments.

• International Journal of Aeronautical and Space Sciences
• /
• 제12권1호
• /
• pp.37-42
• /
• 2011

An extended scalar adaptive filter for guided missiles using a global positioning system receiver is presented. A conventional scalar adaptive filter is adequate filter for eliminating sudden abnormal jumping measurements. However, if missile or vehicle velocities have variation, the conventional filter cannot eliminate abnormal measurements. The proposed filter utilizes an acceleration term, which is an improvement not used in previous conventional scalar adaptive filters. The proposed filter continuously estimates noise measurement variance, velocity error variance and acceleration error variance. For estimating the three variances, an innovation method was used in combination with the least square method for the three variances. Results from the simulations indicated that the proposed filter exhibited better position accuracy than the conventional scalar adaptive filter.

• 한국전산유체공학회지
• /
• 제21권1호
• /
• pp.72-77
• /
• 2016

In this study, effects of thurster axis tilting angle on the thruster-hull interaction and propulsion performance in a dynamic positioning system of offshore plant are numerically investigated. Straight and 7-degree tilted downward thruster models as a form of ducted propeller are considered. For numerical simulations, Reynolds averaged Navier-Stokes equations with SST turbulence model are solved by using STAR-CCM+. Results show that thruster-hull interaction is reduced in 7-degree tilted thruster model with lower vortex strength between thruster and hull bottom, although the propulsion performance does not have noticeable difference in a bollard condition.

• 대한기계학회논문집A
• /
• 제30권5호
• /
• pp.609-614
• /
• 2006

Recently linear motor has been used mainly for high speed feeding performance of machine tools. The advantages of linear motor are not only high speed but high accuracy, because it is not required the coupling and ballscrew for converting rotary to liner motion. Before applying in different moving system, the dynamometer is necessary to test the performance. In Korea, the linear motor is producing in a couple of company However, the liner motor dynamometer is not commercialized yet, like as rotary motor dynamometer. In this paper, a linear motor dynamometer is designed and manufactured using a MR damper. The dynamometer system developed in this study could be used for testing the positioning accuracy fur different loading conditions, traction forces, dynamic performance and so on.