• 대한토목학회논문집
• /
• 제32권6C호
• /
• pp.295-304
• /
• 2012

본 연구에서는 대형 지반구조물의 축조재료로 이용되는 대입경 조립재료의 동적 변형특성을 평가하기 위한 목적으로 국내 최대 규모의 대형 공진주시험시스템을 구축하였으며 그 성능 및 적용성을 검증하였다. 신규 시험기는 하단 고정, 상부 자유단에 코일-자석 시스템에 의한 가진 하중을 제어하는 전형적인 Stokoe 식 공진주시험 장치이며, 지름 200 mm, 높이 400 mm의 원주형 공시체에 대한 시험이 가능다. 시험기의 구동 및 계측 시스템은 굵은 자갈 이상의 조립재료에 대한 활용에 적합하도록 출력 및 정밀도를 확보하였으며, 고정밀의 제어 계측이 가능한 자동화 시스템으로 구성되었다. 공진주시험기의 동적응답특성 및 사용성을 검증하기 위한 방안으로 금속시편과 다수의 폴리우레탄 검증 시편을 이용하여 시험을 수행하였으며 타 시험기 또는 시험기법과의 비교를 통하여 정밀도를 평가하였다. 대형 시험기의 지반재료의 동적 변형특성 평가에 대한 신뢰성을 확인하기 위하여 동일한 사질토 시료에 대한 시험을 일반 공진주시험과 병행한 결과 공시체의 크기에 따른 효과가 일부 나타나지만 전반적으로 동일한 결과를 획득하였다. 최종적으로 댐 축조용 사력재료 시료에 대한 대형 공진주시험을 수행하였으며, 그 결과의 실효성을 확인하였다.

• Journal of Biosystems Engineering
• /
• 제8권2호
• /
• pp.39-48
• /
• 1983

This study was performed to obtain the basic data which could be used for the modification of the manual center-burner-type rice-husk furnace into a small scale automatic type for the multi-purpose use in the farm. For this purpose, first, the utilization feasibility of the rice-husk furnace in the farm was analyzed briefly in aspects of available amount of rice-husk for the fuel, annual operation time and replaceble amount of residential heating energy with rice-husk in the farm. For the experiment a prototype furnace geared with an automatic feeding device was fabricated, and feed rate, mold size and chimney height were changed to investigate the combustion efficiency of rice-husk and thermal efficiency of the furnace. Also, optimum and limiting operational factors were observed in each treatments. The results obtained are summarized as follows. 1. If the rice-husk is intensively used for residential heating in the farm for winter season, on an average 51 percent of the total heating energy can be replaced with the rice-husk. Therefore, development of a small scale automatic rice-husk furnace was recognized to be feasible. 2. The operational condition depending on husk-feed rates was very important factor for successive steady burning operation of the given furnace. When the feed-rate was 1.5 kg/hr, the top of the burning zone should be kept at the position about 55 cm from the bottom of the combustion chamber with the periodic removal of ash (termed as steady state position), which was 18 cm above the mold waist. When the feed rates were 2.4 kg/hr and 3.0 kg/hr, the steady state position was at about 4 cm above the mold waist. 3. The mold size affected inflow rate of air into the furnace and consequently CO content in the exhaust gas. The relatively bigger mold gave positive effect on the air-inflow rate. 4. When the husk-feed rates were 1.5 kg/hr, 2.4 kg/hr, 3.0 kg/hr, the combustion efficiencies of the rice-husk were 98.5%, 97.4% and 95.0%, the thermal efficiencies of the furnace were 93.4%, 93.2% and 87.6%, and CO content in the exhaust gas were 1.21%, 1.03%, and 2.43%, respectively. The air-inflow rates were decreased with the increase of feed rates. When the amount of excess air was 30-40%, the CO content in the exhaust gas was at the minimum level. 5. When the chimney height was lowered from 260 cm to 96 cm, the air-inflow rate was slightly decreased, but the average temperature in the combustion chamber, CO content in the exhaust gas and combustion and thermal efficiencies were not changed significantly. 6. The incidental problems associated with the protytype furnace were accumulation of the ash inside the mold, accumulation of the cinder between the outer-drum of the furnace and the combustion chamber wall, and accumulation of the cinder in the chimney.

• 대한인간공학회지
• /
• 제33권4호
• /
• pp.281-287
• /
• 2014

Objective: The objective of the study is to develop a portable assistance device to help elderly users reduce strain on the knee and leg muscle while the elderly are standing up. Background: The pose of standing up from a chair is a basic movement, but the elderly often have difficulty standing up due to their weak muscles. We focus on designing a solution that helps the elderly reduce physical problems and support them standing up. Method: This study consists of three parts. Part I explores the way to reduce the refrain of leg muscle while standing up from a chair. In the process of structural development, we found that the moment is minimized when user pushes down the armrests due to a decrease in the force acting on the center of mass. In part II, a user test of 20 participants was carried out to rank the order of comfort of two stimuli: the chair with fixed armrests and the chair with the four-link mechanism that we created-in three different ways; (1) to stand up without touching armrests, (2) to stand up by pushing down on fixed armrests, and (3) to stand up by pushing down on armrests and being supported by the mechanism. To examine the statistically significant differences among the rank means, a Friedman test was conducted. In part III, we analyze the results of the user test and interview feedbacks, focusing on establishing a design strategy from UPO and visualizing it in 1:1 scale. Results: In part I, we decided to develop the four-link mechanism. The bottom is lifted up as the link rises. In part II, based on the rank data, we empirically found that UPO was assessed as the most comfortable during the stimuli. The thigh angle is smaller and the bottom of UPO is separated from a seat. In part III, after assessing the results and feedbacks, we created a visualization strategy for UPO: light, friendly, and novel. Conclusion: The portable and non-mechanical UPO comprises a four-link system that lifts the user's hips while standing. It can help users avoid knee and leg muscle strain. Its universal design considers the elderly's difficulties. Application: In a future study, combining light and durable material in UPO is expected to increase its usability. And this study is an opportunity to design various types of standing assistance devices.

• 마이크로전자및패키징학회지
• /
• 제23권2호
• /
• pp.79-84
• /
• 2016

유연전자소자가 외부힘에 의해 변형될 경우 반도체 다이가 기계적 응력 때문에 변형되거나 파괴되고 이러한 변형이나 파괴는 channel의 전자이동도를 변화시키거나 배선의 저항을 증가시켜 집적회로의 동작 오류를 발생시킨다. 따라서 반도체 집적회로는 굽힘 변형이 발생해도 기계적 응력이 발생하지 않는 중립축에 위치하는 것이 바람직하다. 본 연구에서는 굽힘변형을 하는 flip-chip 접합공정이 적용된 face-down flexible packaging system에서 중립축의 위치와 파괴 모드를 조사하였고 반도체 집적회로와 집중응력이 발생한 곳의 응력을 감소시킬 수 있는 방법을 제시하였다. 이를 위해, 설계인자로 유연기판의 두께 및 소재, 반도체 다이의 두께를 고려하였고 설계인자가 중립축의 위치에 미치는 영향을 조사한 결과 유연기판의 두께가 중립축의 위치를 조절하는데 유용한 설계인자임을 알 수 있었다. 3차원 모델을 이용한 유한요소해석 결과 반도체 다이와 유연기판 사이의 Cu bump 접합부에서 항복응력보다 높은 응력이 인가될 수 있음을 확인하였다. 마지막으로 flexible face-down packaging system에서 반도체 다이와 Cu bump 의 응력을 감소시킬 수 있는 설계 방법을 제안하였다.

• 한국재료학회지
• /
• 제22권2호
• /
• pp.61-65
• /
• 2012

A $Li_2O-2SiO_2$ ($LS_2$) glass was investigated as a lithium-ion conducting oxide glass, which is applicable to a fast ionic conductor even at low temperature due to its high mechanical strength and chemical stability. The $Li_2O-2SiO_2$ glass is likely to be broken into small pieces when quenched; thus, it is difficult to fabricate a specifically sized sample. The production of properly sized glass samples is necessary for device applications. In this study, we applied spark plasma sintering (SPS) to fabricate $LS_2$ glass samples which have a particular size as well as high transparency. The sintered samples, $15mm\phi{\times}2mmT$ in size, ($LS_2$-s) were produced by SPS between $480^{\circ}C$ and $500^{\circ}C$ at 45MPa for 3~5mim, after which the thermal and dielectric properties of the $LS_2$-s samples were compared with those of quenched glass ($LS_2$-q) samples. Thermal behavior, crystalline structure, and electrical conductivity of both samples were analyzed by differential scanning calorimetry (DSC), X-ray diffraction (XRD) and an impedance/gain-phase analyzer, respectively. The results showed that the $LS_2$-s had an amorphous structure, like the $LS_2$-q sample, and that both samples took on the lithium disilicate structure after the heat treatment at $800^{\circ}C$. We observed similar dielectric peaks in both of the samples between room temperature and $700^{\circ}C$. The DC activation energies of the $LS_2$-q and $LS_2$-s samples were $0.48{\pm}0.05eV$ and $0.66{\pm}0.04eV$, while the AC activation energies were $0.48{\pm}0.05eV$ and $0.68{\pm}0.04eV$, respectively.

• 마이크로전자및패키징학회지
• /
• 제24권4호
• /
• pp.39-46
• /
• 2017

본 연구는 평판형 히터용 금속방열판상의 세라믹 절연층 제조, 즉 절연성 금속기판에 관한 것이다. 반도체나 디스플레이의 열처리 공정 등에 사용되는 평판형 히터를 제조함에 있어서, 온도 균일도를 높이기 위해 금속 방열판으로서 열전도율이 높고, 비교적 가벼우며, 가공성 좋은 알루미늄 합금 기판이 선호된다. 이 알루미늄 기판에 발열 회로 패턴을 형성하기 위해서는 금속 기판에 절연층으로서 고온 안정성이 우수한 세라믹 유전체막을 코팅하여야 한다. 금속 기판상에 세라믹 절연층을 형성함에 있어서 가장 빈번히 발생하는 첫 번째 문제는 금속과 세라믹의 이종재료 간의 큰 열팽창계수 차이와 약한 결합력에 의한 층간박리 및 균열발생이다. 두 번째 문제는 절연층의 소재 및 구조적 결함에 따른 절연파괴이다. 본 연구에서는 이러한 문제점 해소를 위해 금속소재 기판과 세라믹 절연층 사이에 완충층을 도입하여 이들 간의 기계적 매칭과 접합력 개선을 도모하였고, 다중코팅 방법을 적용하여 절연막의 품질과 내전압 특성을 개선하고자 하였다.

• 한국화재소방학회논문지
• /
• 제31권3호
• /
• pp.63-72
• /
• 2017

본 논문에서는 저압용 10회로 분전반을 전기공업협동조합(KEMC) 2102-610 규정에 근거하여 제작하였다. 또한, 개발된 10회로 분전반의 특성 평가를 실시하여 안전성을 확보하고자 한다. 개발된 10회로 분전반은 내식성, 절연 재료의 특성, 자외선 복사의 내성, 기계적 충격 등에 적합하도록 설계되었다. 개발된 분전반은 외함의 보호 등급, 감전방지와 보호회로, 개폐 장치와 구성품, 내부 전기 회로와 연결부, 외부 도체의 단자, 절연 특성, 온도 상승 시험, 열저항 등이 적합하도록 제작하였다. 개발된 10회로 분전반은 단상 회로와 3상 회로 등으로 구분되어 있다. 분기된 각각의 차단기 부하측에 센서 모듈을 설치하여 부하의 전선로에서 발생되는 누설전류의 크기를 실시간 측정할 수 있다. 그리고 부하의 용도 및 목적 등에 따라 회로를 증설할 수 있고, 각각의 부하 상태 역시 실시간 부하 관리 및 점검이 가능하다. 개발된 10회로 분전반의 온도 상승 시험을 실시한 곳은 인입 접속부, 주회로 및 분기회로 모선, 모선지지물 등 18 개소이다. 온도가 가장 높게 측정된 곳은 분기회로 모선용 MCCB 전원측 접속부의 R-phase으로 $65.3^{\circ}C$, 부하측은 T-phase으로 $61.6^{\circ}C$로 기록되었다. 그리고 내열 실험 장치를 이용하여 MCCB를 $180^{\circ}C$에서 6시간 동안 열적 스트레스를 인가하였을 때 작동 손잡이의 변형이 확인되었고, 트립 상태로 이동한 것이 확인되었다.

• Journal of Acupuncture Research
• /
• 제19권3호
• /
• pp.64-76
• /
• 2002

Objective : The purpose of this study is to investigate the mechanism and effect of moxibustion objectively and to be used as the quantitative data for developing the new thermal stimulating treatment by observing the combustion characteristics of commercial moxaes. Methods : We have selected two types(large-size moxa A(LMA), large-size moxa B(LMB)) among large moxaes used widely in the clinic. We examined combustion times, temperatures, temperature gradients in each period during a combustion of moxa. Results : 1. The ascending temperature gradient measured in the central point of non-contacted surface was fastest, the average ascending temperature gradient of both moxaes was $0.0384^{\circ}C/sec$, $0.0123^{\circ}C/sec$ respectively, 3.1 times faster in LMA. The maximum ascending temperature gradient was also about 2.9 times faster in LMA. The time required for the maximum ascending temperature gradient from ignition was 254sec, 411sec respectively. 2. The minimum descending temperature gradient in the retaining period was $-0.0250^{\circ}C/sec$, $-0.0090^{\circ}C/sec$ respectively and the average descending temperature gradient was $-0.0160^{\circ}C/sec$, $-0.0037^{\circ}C/sec$ respectively on the non-contact surface. 3. On the basis of the non-contact surface($A_I$), the time at which the effective stimulus period began to occur was about 264sec, 796sec respectively after an ignition, the time at which the maximum temperature began to occur was about 373sec, 1323sec respectively after an ignition, and the maximum temperature was $0.9^{\circ}C$ higher in LMA. The maximum ascending temperature gradient was also about 4.2 times faster in LMA. Conclusion : It was thought that not only the figure of moxicombustion device, but also the form and size of moxa had influence on the combustion characteristics deciding the performance of stimulus seriously.

• 구강회복응용과학지
• /
• 제31권4호
• /
• pp.301-309
• /
• 2015

목적: 무치악 부위를 임플란트 보철로 수복하면 기능저하 상태였던 대합치는 생리적인 자극을 받게 된다. 본 연구는 하악 구치부 임플란트에 대합되는 상악치아의 골변화를 평가하였다. 연구 재료 및 방법: 보철물 장착시(기준점) 및 3, 6개월 후에 방사선 사진을 채득하였다. 맞춤형 필름유지기구를 제작하여 대합치의 연속적인 방사선 사진에 대한 투사를 표준화하였다. 디지털사진에서 관심부위에 대한 그레이수치를 시간별로 측정하여 95% 유의수준으로 반복측정분산분석으로 통계적 유의성을 검증하였다. 결과: 대합치의 그레이수치는 시간이 흐름에 따라 증가하였다. 치조정부위보다 중앙부위의 변화가 더 컸으나 근심과 원심의 그레이수치는 큰 차이를 나타내지 않았다. 그레이수치의 변화는 하중을 가하지 않았던 기간에 따라 다른 양상을 나타내었다. 결론: 기능저하였던 치아주변의 골조직에 기능적 하중이 가해지면 골조직의 변화가 발생할 수 있는 것으로 사료된다.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2017년도 춘계공동학술대회
• /
• pp.156-156
• /
• 2017

Most crop damages have been occurred by vermin(e.g., wild birds and herbivores) during the period between seeding and the cotyledon level. In this study, to minimize the damage by vermin and acquire the benefits such as protection against weeds and maintenance of water content in soil, immediately vinyl mulching after seeding was devised. Vinyl mulching has been generally covered with black color vinyl, that crop seeding locations cannot be detected by visible light range. Before punching vinyl, non-contact and non-destructive methods that can continuously determine the locations are necessary. In this study, a crop position detection method was studied that uses infrared thermal image sensor to determine the cotyledon position under vinyl mulch. The moving system for acquiring image arrays has been developed for continuously detecting crop locations under plastic mulching on the field. A sliding mechanical device was developed to move the sensor, which were arranged in the form of a linear array, perpendicular to the array using a micro-controller integrated with a stepping motor. The experiments were conducted while moving 4.00 cm/s speed of the IR sensor by the rotational speed of the stepping motor based on a digital pulse width modulation signal from the micro-controller. The acquired images were calibrated with the spatial image correlation. The collected data were processed using moving averaging on interpolation to determine the frame where the variance was the smallest in resolution units of 1.02 cm. For this study, the spline method was relatively faster than the other polynomial interpolation methods, because it has a lower maximum order of formulation when using a system such as the tridiagonal linear equation system which provided the capability of real-time processing. The temperature distribution corresponding to the distance between the crops was 10 cm, and the more clearly the leaf pattern of the crop was visually confirmed. The frequency difference was decreased, as the number of overlapped pixels was increased. Also the wave pattern of points where the crops were recognized were reduced.