• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.35-41
• /
• 1999

Friction and wear test was performed for nylon, acetal resin, and PTFE(polytetrafluoroethylene) under reciprocating dry sliding conditions against a steel counterpart. Friction coefficient and specific wear rate were analysed as a function of sliding distance and applied load. The worn surfaces of plate and disc specimens were observed using SEM(Scanning Electron Microscopy). The experimental results show that acetal resin exhibited lowest wear rates whereas PTFE possessed lowest friction coefficient. The prominent wear mechanisms found were adhesion and abrasion.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 춘계학술대회 논문집 기술교육전문연구회
• /
• pp.31-34
• /
• 2003

The sapphire wafers for blue light emitting devices were manufactured by the implementation of the surface machining technology based on micro-tribology. This process has been performed by chemical and mechanical polishing(CMP) process. The sapphire crystalline wafers were characterized by double crystal X-ray diffraction. The sample quality of sapphire crystalline wafer at surfaces has a full width at half maximum 89 arcses. The surfaces of sapphire wafers were mechanically affected by residual stress and surface default. Sapphire wafers's waveness has higher abrasion rate in the edge of the wafer than its center due to Newton's Ring interference.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2016년도 추계학술대회 논문집
• /
• pp.115.2-115.2
• /
• 2016

Al alloys are being used widely for automobile, aerospace and mechanical components because of their high strength ratio to weight. However, still they suffer from abrasion or corrosion owing to insufficient resistances to friction or mechanical impact and chemical attack. Plasma electrolytic oxidation (PEO) method is one of the promising surface treatment methods for Al alloys which can render better hardness than aluminum anodic oxide (AAO) films prepared by conventional anodizing method in acidic solutions. In this presentation, some basic nature of PEO film formation and growth process on Al alloys will be presented based on the experimental results obtained and discussed in view of dielectric breakdown and reformation and the role of various anions in film breakdown and reformation of PEO films.

• Elastomers and Composites
• /
• 제54권4호
• /
• pp.279-285
• /
• 2019

Bio-based polyester polyols were synthesized using esterification with azelaic acid, sebacic acid, and 1,3-propanediol. Polyurethanes were prepared using chain extenders (1,4-Butanediol, 1,3-Propanediol, and isosorbide) and 4,4'-diphenylmethane diisocyanate with a mixing ratio of 1:1:1.1. Subsequently, the properties of the polymers prepared using the different chain extenders were compared. The synthesis of polyurethane was confirmed by FT-IR, TGA, and GPC. The mechanical properties (hardness, ball rebound, and tensile strength) of the materials were analyzed using shore A tester, taber abrasion, and UTM. heat, chemical, and water resistances of the prepared materials were measured by comparing the tensile strengths according to external changes.

• 한국분말재료학회지
• /
• 제26권3호
• /
• pp.195-200
• /
• 2019

Whisker-type magnesium hydroxide sulfate hydrate ($5Mg(OH)_2{\cdot}MgSO_4{\cdot}3H_2O$, abbreviated 513 MHSH), is used in filler and flame-retardant composites based on its hydrate phase and its ability to undergo endothermic dehydration in fire conditions, respectively. In general, the length of whiskers is determined according to various synthetic conditions in a hydrothermal reaction with high temperature (${\sim}180^{\circ}C$). In this work, high-quality 513 MHSH whiskers are synthesized by controlling the concentration of the raw material in ambient conditions without high pressure. Particularly, the concentration of the starting material is closely related to the length, width, and purity of MHSH. In addition, a ceramic-coating system is adopted to enhance the mechanical properties and thermal stability of the MHSH whiskers. The physical properties of the silica-coated MHSH are characterized by an abrasion test, thermogravimetric analysis, and transmission electron microscopy.

• Tribology and Lubricants
• /
• 제24권4호
• /
• pp.186-189
• /
• 2008

The flow induced vibration in the nuclear fuel assembly causes the fretting wear between the fuel cladding tubes and the supporting grids. The reduction in tube thickness due to the fretting wear could be related to the serious damage on nuclear fuel assembly. In this paper, the effect of the water flow on fretting wear of nuclear fuel cladding tube against supporting grid was investigated through the fretting wear tester with water spout equipment. The test results were compared with the data conducted in the stationary water. At stationary water environment the wear debris was trapped between fretting surfaces, and then the fretting wear occurred by three-body abrasion. However, in the case of water flow, the two-body abrasive wear was the dominant wear mechanism, because the wear debris was easily removed by water flow.

• 한국주조공학회지
• /
• 제8권3호
• /
• pp.296-309
• /
• 1988

In this study the mechanical properties of ferritic ductile cast iron in as-cast are discussed by metallographic considering the effect of phosphorus content(about 0 - 0.8wt.%). In ferritic S.G. cast iron containing about 4.2wt.% Si, 0.5wt.% Ni, 0.02wt.%B, these samples are investigated for castability, microstructure, machinability, wear resistance, mechanical and thermal properties. The main results are summarized as follows. 1) The chill depth increased greatly with P addition up to about 0.6wt.% but the tensile strength and the elongation are decreased smoothly. 2) The size of S.G. and the amount of steadite increase with increasing P content. This means the tendency of increasing the number of S.G. 3) The maximum value of wear by mechanical fracture was appeared at the abrasion speed of 1.14m/sec and the plastic Flow layers are stretched longly on the wear surface with decreasing P content. 4) Although the coefficient of thermal expansion increased with P addition, the cast iron growth was slowing down extremely at 0.6w.% P or more.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.123-129
• /
• 2022

Quartz (SiO2) has high abrasion and heat resistances and excellent chemical and mechanical properties; therefore, it is used in various industries, such as machinery, chemistry, optics, and medicine. Quartz is a high-hardness and brittle material and is classified as the topmost difficult-to-cut material, which is because of the cracking or chipping at the edge during processing. Corner wear, such as cracks and chippings that occur during cutting, is a major cause for the deterioration in the machining quality. Therefore, many researchers are investigating various techniques to process quartz effectively. However, owing to the mechanical properties of quartz, most studies have been conducted on grinding, micromachining, and microdrilling. Few studies have been conducted on quartz processing. The purpose of this study was to analyze the machining characteristics according to the machining factors during the slot machining of quartz using a cubic boron nitride (CBN) tool and to select the optimal machining conditions using the Taguchi method. The machining experiment was performed considering three process variables: the spindle speed, feed rate, and depth of cut. The cutting force and surface roughness were analyzed according to the processing conditions.

• 한국기계가공학회지
• /
• 제14권2호
• /
• pp.19-24
• /
• 2015

Gears are produced through a variety of methods. In general, a metal piece is formed into the general shape of a gear through rough cuts. The gear then moves on to a more precise machine that removes more material. Grinders work via abrasion, rubbing a rough surface against a work piece at such high speeds that it literally scrapes unwanted material away from the item. Since the grinder is spinning so fast, the material is removed very quickly. This allows a grinder to remove a very small amount without taking any unwanted material with it. This study investigates the effect of grinding process parameters like grinding spindle speed and table transfer speed on the gear grade and grinding efficiency.

• 한국의류산업학회지
• /
• 제14권4호
• /
• pp.635-640
• /
• 2012

In this study, thermoplastic urethane (TPU) coating yarns were prepared at various extruding temperatures. The fine structure and mechanical properties of resultant TPU coating yarns examined by the wide angle X-ray diffractometer (WAXD), differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile test. TPU coating yarns (prepared at extruding temperatures at $175^{\circ}C$) were confirmed as a stable fine structure that obtained excellent tensile strength and flexibility. The C samples prepared by optimized conditions made by TPU woven floor mat. The structure of the woven mat is $4{\times}4$ basket weave and have laminated with the EVA foam to obtained final TPU woven floor mat products. The resultant TPU woven floor mat was obtained to 1.5MN of tensile strength, 22% of the elongation, and 0.2MN of tear strength. The weight loss abrasion and the resilience by the ball rebound of the TPU-woven floor mat was prior to those of the PVC subsequently, we were able to develop a woven floor mat with TPU coating yarn and produce an eco-friendly high valuable woven floor mat using an interior product.