• Archives of Pharmacal Research
• /
• v.27 no.6
• /
• pp.646-652
• /
• 2004

The objective of this study was to determine the acute effect of trimetazidine (TMZ) on the pre-fatigue, fatigue and post-fatigue contractile characteristics and tension-frequency relationships of isolated rat diaphragm muscle. Muscle strips were taken from the ventral-costal aspects of the diaphragm muscle of rats killed by decapitation. The muscle strips were suspended in organ baths containing Krebs solution, with a gas mixture of 95% $O_2$ and 5% $CO_2$ at $37^{\circ}C$ and pH 7.35-7.45. After determining the thermoregulation and optimum muscle length the muscles were subjected to direct supramaximal stimulation with 0.05 Hz frequency square pulses for periods of 0.5 msec to obtain control values. After adding $5{\times}10^{-6}{\;}and{\;}5{\times}10^{-5}$ M trimetazidine solution to the respective bath media, the contractile parameters of the muscles were recorded. The contractile parameters were also recorded for both the trimetazidine and tri-metazidine-free media after application of the high frequency fatigue protocols. Later, the tension-frequency relationship was determined by applying stimulating pulses of 10, 20, 50 and 100 Hz to the muscle strips. Whilst the twitch tension obtained from the $5{\times}10^{-6}{\;}and{\;}5{\times}10^{-5}$ M trimetazidine media showed numerical increases compared to that of the controls, these were not statistically significant (p>0.05). The contraction time exhibited a dose dependent increase (p<0.001), whilst the contraction and relaxation rates did not differ significantly. The isometric contraction forces obtained with the different stimulating frequencies showed a significant increase in the tetanic contraction only at 100 Hz (p<0.05). A comparison of the pre- and post-fatigue twitch tensions in the trimetazidine media showed the post- fatigue twitch tensions to be significantly higher than those of the pre-fatigue contraction forces (p<0.05). In the $5{\times}10^{-6}{\;}and{\;}5{\times}10^{-5}$ M trimetazidine media the increases in the post-fatigue contraction force were 22 and 30%, respectively. These results demonstrated that in isolated rat diaphragm muscle, TMZ significantly limited the mechanical performance decrease during fatigue. It is our opinion that trimetazidine contributed to the observed fatigue tolerance by eliminating the factors of fatigue, due to preservation of intracellular calcium homeostasis, provision of the ATP energy levels needed by ATPase dependent pumps and especially by keeping the intracellular pH within cer-tain limits.

• Journal of the Korean Society for Railway
• /
• v.19 no.5
• /
• pp.629-637
• /
• 2016

In this paper, an investigation was conducted to evaluate the acoustic performance of low height noise barriers installed adjacent to rails; an easy-to-use approximation formula was suggested for the evaluation of insertion loss (IL), instead of using the boundary element method. At first, the acoustic performance of the low height noise barriers was measured in an anechoic chamber using a scaled down model; the overall IL according to the source location was analyzed with the equivalent IL contour line. Using the measurement results obtained from the scaled down model, an approximation formula was suggested for the IL of low height noise barriers having various shapes. Also, the prediction program was validated through a comparison between the actual measurement results in the anechoic chamber and the prediction results. Finally, using the prediction program, an approximation formula for IL was suggested for the low height noise absorption barriers. Considering the frequency characteristics of the noise sources of the train, the absorptive low height noise barriers have a 'ㄱ' type shape, a height of 1.0m, and a length of 0.5m when they are installed on the structure gauge for the train.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.52.2-52.2
• /
• 2014

The Immersion Grating Infrared Spectrometer (IGRINS) is an unprecedentedly minimized infrared cross-dispersed echelle spectrograph with a high-resolution and high-sensitivity optical performance. A silicon immersion grating features the instrument for the first time in this field. IGRINS will cover the entire portion of the wavelength range between 1.45 and $2.45{\mu}m$ accessible from the ground in a single exposure with spectral resolution of 40,000. Individual volume phase holographic (VPH) gratings serve as cross-dispersing elements for separate spectrograph arms covering the H and K bands. On the 2.7m Harlan J. Smith telescope at the McDonald Observatory, the slit size is $1^{\prime\prime}{\times}15^{\prime\prime}$. IGRINS has a $0.27^{\prime\prime}$ pixel-1 plate scale on a $2048{\times}2048$ pixel Teledyne Scientific & Imaging HAWAII-2RG detector with SIDECAR ASIC cryogenic controller. The instrument includes four subsystems; a calibration unit, an input relay optics module, a slit-viewing camera, and nearly identical H and K spectrograph modules. The use of a silicon immersion grating and a compact white pupil design allows the spectrograph collimated beam size to be 25mm, which permits the entire cryogenic system to be contained in a moderately sized rectangular vacuum chamber. The fabrication and assembly of the optical and mechanical hardware components were completed in 2013. In this presentation, we describe the major design characteristics of the instrument and the early performance estimated from the first light commissioning at the McDonald Observatory.

• Journal of the Korea Concrete Institute
• /
• v.23 no.1
• /
• pp.3-12
• /
• 2011

The structural behavior of continuous reinforced concrete deep beams is mainly controlled by the mechanical relationships associated with the shear span-to-effective depth ratio, flexural reinforcement ratio, load and support conditions, and material properties. In this study, a simple indeterminate strut-tie model which reflects characteristics of the complicated structural behavior of the continuous deep beams is presented. In addition, the reaction and load distribution ratios defined as the fraction of load carried by an exterior support of continuous deep beam and the fraction of load transferred by a vertical truss mechanism, respectively, are proposed to help structural designers for the analysis and design of continuous reinforced concrete deep beams by using the strut-tie model approaches of current design codes. In the determination of the load distribution ratio, a concept of balanced shear reinforcement ratio requiring a simultaneous failure of inclined concrete strut and vertical steel tie is introduced to ensure a ductile shear failure of reinforced concrete deep beams, and the primary design variables including the shear span-to-effective depth ratio, flexural reinforcement ratio, and concrete compressive strength are implemented after thorough parametric numerical analyses. In the companion paper, the validity of the presented model and load distribution ratio was examined by applying them in the evaluation of the ultimate strength of multiple continuous reinforced concrete deep beams, which were tested to failure.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.2 no.1
• /
• pp.136-143
• /
• 2006

In this study, recently it is urgently required that demolition waste concrete has to be recycled on the construction because urban development is accelerated and redevelopment project is rapidly expanded, production quantity of construction and demolition waste concrete is being increased. As a results of drying shrinkage test under restrained and unrestrained condition, although workability and mechanical properites of concrete using HQRS were similar to that of concrete using natural sand, there were a great difference in deformation characteristic of dry shrinkage according to replacement ratio of HQRS. And, it makes sure that use of HQRS instead of partial nature sand was effective because drying shrinkage of concrete using 30 volume percentage of HQRS was smaller than that using only natural sand. Therefore, it is the objective of this study to provide the fundamental data about the re-application as an analysis of the drying shrinkage characteristics of concrete using HQRS and it is able to creta a high value-added by using HQRS.

• Korean Chemical Engineering Research
• /
• v.45 no.4
• /
• pp.328-334
• /
• 2007

Chemical heat pump system of 2-propanol/acetone/hydrogen is most suitable to the recovery of waste heat of power plant. various types of 5 wt% Pt-alumina catalysts were prepared for 2-propanol dehydrogenation using sol-gel method. The characteristics and the dehydrogenation reaction rate of each catalyst were investigated. Pt-alumina xerogel catalyst has excellent reaction rate and good durability in comparison with the existing alumina supported Pt catalysts. Pt-alumina aerogel catalyst had the highest reaction rate in all prepared catalysts, but sufficient aging time was necessary to maintain its reaction rate. A potential advantage of the aerogel catalyst is the fact that the high temperature heat treatment is not required. Without heat treatment or with low temperature heat treatment, the Pt-alumina aerogel catalyst has excellent reaction rate as well as durability and this gives us the economic advantage. Alumina xerogel supported Pt catalyst prepared by incipient wetness method showed good reaction rate, and had good mechanical strength. Blank alumina xerogel prepared by sol-gel method can be used for the support of metal catalysts.

• Journal of dental hygiene science
• /
• v.17 no.2
• /
• pp.87-98
• /
• 2017

The purpose of this study was to understand the effectiveness of oral health education (OHE) or oral hygiene instruction (OHI) involving professional plaque control/removal, as compared to conventional plaque control/removal. By means of a systematic review of the literature, in the review of literature by using systematic method, Korean articles of plaque control including OHE or OHI, were studied in order to analyze and conclude the literature to enhance oral health. We found that self and professional plaque control/removal, in addition to tooth brushing instructions, decreased incidence and prevalence of loss of teeth. Taken together, professional mechanical plaque removals were most effective 4~5 visits every 1~2 weeks. Use of disclosing agent was more effective than oral education or model education. In line with oral hygiene education, professional brushing, oral prophylaxis, scaling and root planing, it was advisable to repeat the training according to the characteristics of the patient. Routine OHE or OHI would be help to increase to oral health. For a quality of life related oral health, reliability and validity of data are needed to develop and its data should be applied to dental health insurance policy.

• Advanced Composite Materials
• /
• v.17 no.1
• /
• pp.25-40
• /
• 2008

The research and development in soundproof materials for preventing noise have attracted great attention due to their social impact. Noise insulation materials are especially important in the field of soundproofing. Since the insulation ability of most materials follows a mass rule, the heavy weight materials like concrete, lead and steel board are mainly used in the current noise insulation materials. To overcome some weak points in these materials, fiber reinforced composite materials with lightweight and other high performance characteristics are now being used. In this paper, innovative insulation sheet materials with carbon and/or glass fabrics and nano-silica hybrid PU resin are developed. The parameters related to sound performance, such as materials and fabric texture in base fabric, hybrid method of resin, size of silica particle and so on, are investigated. At the same time, the wave analysis code (PZFlex) is used to simulate some of experimental results. As a result, it is found that both bundle density and fabric texture in the base fabrics play an important role on the soundproof performance. Compared with the effect of base fabrics, the transmission loss in sheet materials increased more than 10 dB even though the thickness of the sample was only about 0.7 mm. The results show different values of transmission loss factor when the diameters of silica particles in coating materials changed. It is understood that the effect of the soundproof performance is different due to the change of hybrid method and the size of silica particles. Fillers occupying appropriate positions and with optimum size may achieve a better effect in soundproof performance. The effect of the particle content on the soundproof performance is confirmed, but there is a limit for the addition of the fillers. The optimization of silica content for the improvement of the sound insulation effect is important. It is observed that nano-particles will have better effect on the high soundproof performance. The sound insulation effect has been understood through a comparison between the experimental and analytical results. It is confirmed that the time-domain finite wave analysis (PZFlex) is effective for the prediction and design of soundproof performance materials. Both experimental and analytical results indicate that the developed materials have advantages in lightweight, flexibility, other mechanical properties and excellent soundproof performance.

• Computers and Concrete
• /
• v.3 no.5
• /
• pp.301-312
• /
• 2006

Experimental research revealed that the spatial dispersion of aggregate grains exerts pronounced influences on the mechanical and durability properties of concrete. Therefore, insight into this phenomenon is of paramount importance. Experimental approaches do not provide direct access to three-dimensional spacing information in concrete, however. Contrarily, simulation approaches are mostly deficient in generating packing systems of aggregate grains with sufficient density. This paper therefore employs a dynamic simulation system (with the acronym SPACE), allowing the generation of dense random packing of grains, representative for concrete aggregates. This paper studies by means of SPACE packing structures of aggregates with a Fuller type of size distribution, generally accepted as a suitable approximation for actual aggregate systems. Mean free spacing $\bar{\lambda}$, mean nearest neighbour distance (NND) between grain centres $\bar{\Delta}_3$, and the probability density function of ${\Delta}_3$ are used to characterize the spatial dispersion of aggregate grains in model concretes. Influences on these spacing parameters are studied of volume fraction and the size range of aggregate grains. The values of these descriptors are estimated by means of stereological tools, whereupon the calculation results are compared with measurements. The simulation results indicate that the size range of aggregate grains has a more pronounced influence on the spacing parameters than exerted by the volume fraction of aggregate. At relatively high volume density of aggregates, as met in the present cases, theoretical and experimental values are found quite similar. The mean free spacing is known to be independent of the actual dispersion characteristics (Underwood 1968); it is a structural parameter governed by material composition. Moreover, scatter of the mean free spacing among the serial sections of the model concrete in the simulation study is relatively small, demonstrating the sample size to be representative for composition homogeneity of aggregate grains. The distribution of ${\Delta}_3$ observed in this study is markedly skew, indicating a concentration of relatively small values of ${\Delta}_3$. The estimate of the size of the representative volume element (RVE) for configuration homogeneity based on NND exceeds by one order of magnitude the estimate for structure-insensitive properties. This is in accordance with predictions of Brown (1965) for composition and configuration homogeneity (corresponding to structure-insensitive and structure-sensitive properties) of conglomerates.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.387-392
• /
• 2015

A method for measuring and analyzing the $NO_x$ in ships is described in $NO_x$ Technical Code 2008. The analysis device, as required by the Code, has been to use a Chemi-luminescence detection method or Heated Chemi-luminescence detection. on the other hand, selective catalytic reduction using $NH_3$ as a reducing agent has an interference effect on the analyzer, and causes measurement error. In this study, the Chemi-luminescence detection method was examined according to how it affects the concentration of $O_2$, CO, $SO_2$, $NH_3$. Fourier transform infrared spectrometry analysis equipment and measurement methods were compared. In order to confirm the effect of the physical interference of the measuring device, it was confirmed by decomposing a measuring device. Consequently, white precipitate and moisture were generated inside the chemiluminescence detection system and I found that affecting interference. The influence of interference highlights the need to consider the minimized $NO_x$ measurement method.