• Journal of Korean Society for Atmospheric Environment
• /
• v.8 no.2
• /
• pp.93-99
• /
• 1992

Recently a passive $NO_2$ samplers have been frequently used for the measurement of $NO_2$ concentration in the atmosphere because of its simplicity and high accuracy. But these samplers have a defect that the amount of $NO_2$ adsorbed is increased by wind. In this study, the inlet of sampler was covered with a draft shield made by 325 mesh stainless sieve to eliminate the effect. But it was expected that $NO_2$ diffusion was interrupted by the draft shield. In order to conform this phenomenon, samplers with and without draft shield were exposed to a box filled with 1-1.1ppm $NO_2$. The result indicated that draft shield nearly did not disturb $NO_2$ diffusion. To protect samplers from dust, sunshine, precipitation and vertical wind effects, these samplers were placed into a shelter during the field test. The data obtained in this study was compared with the data from the ambient air monitoring network. The coefficient of correlation(r) between the two data was 0.9995 for the test period of up to 35days. The results of this study indicate that the type of $NO_2$ samplers with draft shield in shelter used in this study can be used for measuring $NO_2$ concentrations in the ambient air relatively for a long period over 30 days.

• Korean Journal of Materials Research
• /
• v.21 no.10
• /
• pp.546-549
• /
• 2011

Nano-sized $SnO_2$ thick films were prepared by a screen-printing method onto $Al_2O_3$ substrates. The sensing characteristics were investigated by measuring the electrical resistance of each sensor in a test box as a function of the detection gas. The nano-sized $SnO_2$ thick film sensors were treated in a $N_2$ atmosphere. The structural properties of the nano $SnO_2$with a rutile structure according to XRD showed a (110) dominant $SnO_2$ peak. The particle size of $SnO_2$:Ni nano powders at Ni 8 wt% was about 45 nm, and the $SnO_2$ particles were found to contain many pores according to the SEM analysis. The sensitivity of the nano $SnO_2$-based sensors was measured for 5 ppm $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature by comparing the resistance in air with that in the target gases. The results showed that the best sensitivity of $SnO_2$:Ni and $SnO_2$:Co sensors for $CH_4$ gas and $CH_3CH_2CH_3$ gas at room temperature was observed in $SnO_2$:Ni sensors doped with 8 wt% Ni. The response time of the $SnO_2$:Ni gas sensors was 10 seconds and recovery time was 15 seconds for the $CH_4$ and $CH_3CH_2CH_3$ gases.

• Journal of the Korean institute of surface engineering
• /
• v.35 no.1
• /
• pp.39-46
• /
• 2002

$Cu_2$$ZnSnS_4$(CZTS) thin film is one of the candidate materials for the solar cell. It has an excellent optical absorption coefficient as well as appropriate 1.4~1.5eV band gap. The purpose of this study is replacing a half of high-cost Indium(In) atoms with low-cost Zinc(Zn) atoms and the other half with low-cost Tin(Sn) atoms in the lattice of CIS. Thin films were deposited on ITO glass substrates using a compact target which were made by $Cu_2$S, ZnS, SnS$_2$ powder at room temperature by rf magnetron sputtering and were annealed in the atmosphere of Ar and $S_2$(g). We investigated potentialities of a low-cost material for the solar cell by measuring of thin film composition, the structure and optical properties. We could get an appropriate $Cu_2$$ZnSnS_4$ composition. Structure was coarsened with increasing temperature and (112), (200), (220), (312) planes appeared to conform to all the reflection Kesterite structure. A (112) preferred orientation was advanced with increasing the annealing temperature as shown in the diffraction peaks of the CIS cells and was available for photovoltaic thin film materials. The band gap increased from 1.51 to 1.8eV as the annealing temperature increased. The optical absorption coefficient of the thin film was about $10^4$$cm^{-1}$.

• Journal of Adhesion and Interface
• /
• v.8 no.3
• /
• pp.16-23
• /
• 2007

Polyester fabrics and knits were corona treated with different current intensity (5, 10, 15, 20 A) and feeding speed (5, 10, 15 m/min). We confirmed the surface change of polyester fabrics and knits using scanning electron microscopy (SEM) and X-ray photoelectron spectrometer (XPS). And the change of physical properties through measuring the tensile strength, dry and wet bonding strength. Thermosetting reactive polyurethane hot melt adhesive was used in the adhesion of polyester fabrics and knits. Functional groups were introduced on PET fabrics and knits surface by treating the PET fabrics and knits in air atmosphere with corona discharge, and take placed unevenness, the result adhesion was improved. When consider both dry and wet bonding strength, we think that appropriate conditions in the PET fabrics corona treatment are feeding speed 10 m/min, current intensity 15 A and appropriate conditions in the mesh type PET knits corona treatment are feeding speed 10 m/min, current intensity above 10 A.

• Journal of Adhesion and Interface
• /
• v.17 no.3
• /
• pp.104-109
• /
• 2016

Compare AC corona and DC corona treatment effects, polyester fabrics were AC corona treated with different current intensity (5, 10, 15 A) and feeding speed (5, 10, 15 m/min) as the same DC corona treatment conditions of the preceding research. We confirmed the surface change of polyester fabrics using scanning electron microscopy (SEM) and X-ray photoelectron spectrometer (XPS), and the change of physical properties through measuring the dry and wet bonding strength. The surface changes of polyester fabrics by treating in air atmosphere with AC corona discharge are shown similar tendency with DC corona discharge. Generally dry bonding strength were increased with increasing current intensity and feeding speed, but wet bonding strength were increased with increasing current intensity and decreasing feeding speed in both AC and DC corona treatment. When the current is 20 A, carbonization occurs in DC corona discharge but carbonization does not occur in DC corona discharge.

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.299-302
• /
• 2011

[ $WO_3$ ]powders were ball-milled with an alumina ball for 0-72 hours. $In_2O_3$ doped $WO_3$ was prepared by soaking ball-milled $WO_3$ in an $InCl_3$ solution. The mixed powder was annealed at $700^{\circ}C$ for 30 min in an air atmosphere. A paste for screen-printing the thick film was prepared by mixing the $WO_3$:In2O3 powders with ${\alpha}$-terpinol and glycerol. $In_2O_3$ doped $WO_3$ thick films were fabricated into a gas sensor by a screen-printing method on alumina substrates. The structural properties of the $WO_3$:$InO_3$ thick films were a monoclinic phase with a (002) dominant orientation. The particle size of the $WO_3$:$InO_3$ decreased with the ball-milling time. The sensing characteristics of the $In_2O_3$ doped $WO_3$ were investigated by measuring the electrical resistance of each sensor in the test-box. The highest sensitivity to 5 ppm $CH_4$ gas and 5 ppm $CH_3CH_2CH_3$ gas was observed in the ball-milled $WO_3$:$InO_3$ gas sensors at 48 hours. The response time of $WO_3$:$In_2O_3$ gas sensors was 7 seconds and recovery time was 9 seconds for the methane gas.

• Hwankyungkyoyuk
• /
• v.8 no.1
• /
• pp.66-80
• /
• 1995

The purpose of this study was to investigate the housewives's recognition and practice on prevention of environmental pollution. The subjects of this study were 250 housewives, school students' mothers, living in Cheong-ju. Major findings were as follows: 1. In washing their faces and brushing their teeth, they saved the water very well, but in taking bath, washing the dished, using the water of the lavatory they did not save the water so well. 2. The kinds of the cleansers differed in taking a bath, washing the hair, and doing the laundry respectively : what they use most was hard soaps in taking bath, liquid cleansers mixed with shampoo and linse in washing the hair, and synthetic powder detergent in laundrying. They used more synthetic detergent than natural soaps, which is known to be a cause of water pollution. Especially, when they cleansed, they did not use a measuring cup. It resulted in the waste of detergent and accelerating of water pollution. Therefore, the environmental education for them was very urgently needed. 3. In handling domestic waste, the separate collection rate of empty bottles and old newspapers was very high, but that of used phone-call cards and used batteries was extremely low. It was truly nessesary to educate and step up publicic activities on the separate collection of phone-call cards and batteries caused environmental pollution. 4. The housewives had much knowledge about environmental pollution, but they did not practice it so well in their home. 5. The housewives made more effort than their children in preventing environmental pollution and saving resources. In conclusion, what is most important for solving environmental problem was for each citizen to make an effort to prevent environmental pollution, and the government's support and producing the atmosphere of the society for this was really needed.

• Korean Journal of Remote Sensing
• /
• v.28 no.2
• /
• pp.237-243
• /
• 2012

In this paper, an atmospheric effect of repetitive measurements of X-band (9.65 GHz) arc-rail type GB-SAR (ArcSAR) system was quantitatively analyzed. Four artificial triangular trihedral corner reflectors as stationary targets for getting stable back scattered signal during 43 hours continually. The results of the analysis showed that the phase of those stationary targets had changed maximum of 5 radian (12.4 mm) and total RMS error had was 1.62 radian (4 mm) during 65 repeated measuring time. The refractive index of air which was calculated using the temperature;humidity and pressure of atmosphere showed very close relationship with the phase difference. We could check the atmospheric correction was fulfilled by the correction of an atmospheric effect using refractive index during the selected 16 hours period showed that RMS error was dropped from 1.74 radian (4.3 mm) to 0.10 radian (0.24 mm).

• Journal of The Korean Society of Agricultural Engineers
• /
• v.62 no.6
• /
• pp.11-20
• /
• 2020

We estimated the spatio-temporally distributed soil moisture using Sentinel-1A/B SAR (Synthetic Aperture Radar) sensor images and soil moisture data assimilation technique in South Korea. Soil moisture data assimilation technique can extract the hydraulic parameters of soils using observed soil moisture and GA (Genetic Algorithm). The SWAP (Soil Water Atmosphere Plant) model associated with a soil moisture assimilation technique simulates the soil moisture using the soil hydraulic parameters and meteorological data as input data. The soil moisture based on Sentinel-1A/B was validated and evaluated using the pearson correlation and RMSE (Root Mean Square Error) analysis between estimated soil moisture and TDR soil moisture. The soil moisture data assimilation technique derived the soil hydraulic parameters using Sentinel-1A/B based soil moisture images, ASOS (Automated Synoptic Observing System) weather data and TRMM (Tropical Rainfall Measuring Mission)/GPM (Global Precipitation Measurement) rainfall data. The derived soil hydrological parameters as the input data to SWAP were used to simulate the daily soil moisture values at the spatial domain from 2001 to 2018 using the TRMM/GPM satellite rainfall data. Overall, the simulated soil moisture estimates matched well with the TDR measurements and Sentinel-1A/B based soil moisture under various land surface conditions (bare soil, crop, forest, and urban).

• Journal of the Korean institute of surface engineering
• /
• v.49 no.2
• /
• pp.202-210
• /
• 2016

This study was intended to investigate the effect of the amount of magnesium addition and heat treatment in the Al-Mg coating film in order to improve corrosion resistance of aluminum coating. Al-Mg alloy films were deposited on cold rolled steel by physical vapor deposition sputtering method. Heat treatment was fulfilled in an nitrogen atmosphere at the temperature of $400^{\circ}C$ for 10 min. The morphology was observed by SEM, component and phase of the deposited films were investigated by using GDLS and XRD, respectively. The corrosion behaviors of Al-Mg films were estimated by exposing salt spray test at 5 wt.% NaCl solution and measuring polarization curves in deaerated 3 wt.% NaCl solution. With the increase of magnesium content, the morphology of the deposited Al-Mg films changed from columnar to featureless structure and particle size was became fine. The x-ray diffraction data for deposited Al-Mg films showed only pure Al peaks. However, Al-Mg alloy peaks such as $Al_3Mg_2$ and $Al_{12}Mg_{17}$ were formed after heat treatment. All the sputtered Al-Mg films obviously showed good corrosion resistance compared with aluminum and zinc films. And corrosion resistance of Al-Mg film was increased after heat treatment.