본 연구는 항공기 운용 중 발생하는 구조결함의 원인을 규명하고 개선형상에 대한 구조 건전성을 확인하고자 한다. 항공기 균열은 Bulkhead 체결구조로서 연료탱크 경계 Web 파열로 인한 연료누유 현상에서 식별되었다. 균열의 특성을 확인하기 위해 파단면을 분석하였고 반복하중에 의해 균열이 진전되어 최종 파단으로 이어지는 피로파괴로 판단하였다. 또한 다중 시작점에서 균열이 시작되는 것으로 소재의 결함이 균열의 주요 원인으로 판단되지 않는다. 항공기 운용 중 발생하는 기동하중에 대한 균열 영향을 확인하기 위해 항공기 지상 및 비행시험을 통해 분석을 수행하였다. 항공기 운용 중 균열 부위의 하중 측정 데이터와 항공기 설계하중과의 비교를 통한 분석 결과 측정하중은 설계 대비 30% 수준으로 파손을 유발할 수준은 아니라고 판단하였다. 항공기 운용 시 진동하중의 원인으로 조립 및 단품 제작공차가 최대 0.06inch 발생할 수 있는 Gap을 검토하였고, 분석결과 균열부위에서 큰 응력인 약 32ksi가 발생하였다. 또한 Pre-Load에 의해 M.S.(Margin of Safety)가 +0.71에서 +0.34로 약 50%이상 감소되는 것으로 확인되어 항공기 설계 하중과 조합 시 균열 가능성이 급격히 증가하였다. 따라서 항공기 균열부위에 대하여 구조 보강 및 Gap 제거를 통해 결함을 개선하였다. 개선형상에 대하여 구조강도 해석 결과 Bulkhead는 허용응력 대비 M.S.가 약 +0.88이고 Fitting 형상은 약 +0.48로서 충분한 마진이 확보되었다. 또한 수명해석 결과 형상 개선 전 수명인 약3,600 시간 대비 개선형상은 약84,000 시간으로서 항공기 설계수명 대비 구조건전성을 확인하였다.
Kim, Kwan;Choi, Jeong-Yong;Shin, Dong-Ha;Lee, Hyang-Bong;Shin, Kuan-Soo
Bulletin of the Korean Chemical Society
/
제32권spc8호
/
pp.2941-2948
/
2011
A nanogap formed by a metal nanoparticle and a flat metal substrate is one kind of "hot site" for surface-enhanced Raman scattering (SERS). The characteristics of a typical nanogap formed by a planar Au and either an Au and Ag nanoparticle have been well studied using 4-aminobenzenethiol (4-ABT) as a probe. 4-ABT is, however, an unusual molecule in the sense that its SERS spectral feature is dependent not only on the kinds of SERS substrates but also on the measurement conditions; thus further characterization is required using other adsorbate molecules such as 1,4-phenylenediisocyanide (1,4-PDI). In fact, no Raman signal was observable when 1,4-PDI was selfassembled on a flat Au substrate, but a distinct spectrum was obtained when 60 nm-sized Au or Ag nanoparticles were adsorbed on the pendent -NC groups of 1,4-PDI. This is definitely due to the electromagnetic coupling between the localized surface plasmon of Au or Ag nanoparticle with the surface plasmon polariton of the planar Au substrate, allowing an intense electric field to be induced in the gap between them. A higher Raman signal was observed when Ag nanoparticles were attached to 1,4-PDI, irrespective of the excitation wavelength, and especially the highest Raman signal was measured at the 632.8 nm excitation (with the enhancement factor on the order of ${\sim}10^3$), followed by the excitation at 568 and 514.5 nm, in agreement with the finite-difference timedomain calculation. From a separate potential-dependent SERS study, the voltage applied to the planar Au appeared to be transmitted without loss to the Au or Ag nanoparticles, and from the study of the effect of volatile organics, the voltage transmission from Au or Ag nanoparticles to the planar Au also appeared as equally probable to that from the planar Au to the Au or Ag nanoparticles in a nanogap electrode. The response of the Au-Ag nanogap to the external stimuli was, however, not the same as that of the Au-Au nanogap.
Synthesis of ZnCo2O3 oxide is performed by sol-gel method via nitrate-citrate route. Powder X-ray diffraction (XRD) study shows monoclinic unit cell having lattice parameters: a = 5.721(1) Å, b = 8.073(2) Å, c = 5.670(1) Å, β = 93.221(8)°, space group P2/m and Z = 4. Average crystallite sizes determined by Scherrer equation are the range ~14-32 nm, whereas SEM micrographs show nano-micro meter size particles formed in ZnCo2O3. Endothermic peak at ~798 K in the Differential scanning calorimetric (DSC) trace without weight loss could be due to structural transformation and the endothermic peak ~1143 K with weight loss is due to reversible loss of O2 in air atmosphere. Energy Dispersive X-ray (EDX) analysis profile shows the presence of elements Zn, Co and O which indicates the purity of the sample. Magnetic measurements in the range of +12 kOe to -12 kOe at 10 K, 77 K, 120 K and at 300 K by PPMS-II Physical Property Measurement System (PPMS) shows hysteresis loops having very low values of the coercivity and retentivity which indicates the weakly ferromagnetic nature of the oxide. Observed X-band EPR isotropic lineshapes at 300 K and 77 K show positive g-shift at giso ~2.230 and giso ~2.217, respectively which is in agreement with the presence of paramagnetic site Co2+(3d7) in the oxide. DC conductivity value of 2.875 ×10-8 S/cm indicates very weakly semiconducting nature of ZnCo2O3 at 300 K. DRS absorption bands ~357 nm, ~572 nm, ~619 nm and ~654 nm are due to the d-d transitions 4T1g(4F)→2Eg(2G), 4T1g(4F)→4T1g(4P), 4T1g(4F)→4A2g(4F), 4T1g(4F)→4T2g(4F), respectively in octahedral ligand field around Co2+ ions. Direct band gap energy, Eg~ 1.5 eV in the oxide is obtained by extrapolating the linear part of the Tauc plot to the energy axis indicates fairly strong semiconducting nature of ZnCo2O3.
An, Ji Won;Choi, Eun Kyeong;Park, Chol Hee;Choi, Jong Bum;Ko, Dong-Kyun;Lee, Youn-Woo
The Korean Journal of Pain
/
제28권2호
/
pp.109-115
/
2015
Background: This study sought to determine safe ranges of oblique angle, skin entry point and needle length by reviewing computed tomography (CT) scans and to evaluate the usefulness of a bent tip needle during celiac plexus block (CPB). Methods: CT scans of 60 CPB patients were reviewed. Image of the uppermost margin of L2 vertebral body was used to measure the minimal and maximal oblique angles and the distances from the midline to skin puncture point. The imaginary needle trajectory distance was calculated by three-dimensional measurement. When the procedure was performed by using a $10^{\circ}$ bent tip needle under a $20^{\circ}$ oblique X-ray fluoroscopic view, the distance (GF/G'F) from the midline to the actual puncture site was measured. Results: The imaginary safe oblique angle range was $26.4-34.2^{\circ}$ and $27.7-36.0^{\circ}$ on the right and left, respectively. The distance from the midline to skin puncture point was 6.1-7.6 cm on the right and 6.3-7.6 cm on the left. The needle trajectory distance at minimal angle was 9.6-11.6 cm on the right and 9.5-11.5 cm on the left. The distance of GF/G'F was 5.1-6.5 cm and 5.0-6.4 cm on the right and left, respectively. All imaginary parameters were correlated with BMI except for GF/G'F. All complications were mild and transient. Conclusions: We identified safe values of angles and distances using a straight needle. Furthermore, using a bent tip needle under a $20^{\circ}$ oblique fluoroscopic view, we could safely perform CPB with smaller parameter values.
$Cu_xH_3-2_xPMo_{12}O_{40}{\cdot}_nH_2O$에서 구리의 치환양 x를 변화시켜 여러 가지의 헤테로폴리산 동염 촉매를 제조하고, 열분석, X-선 회절분석, 적외선 분광분석, 비표면적 측정, 전자현미경 분석, 암모니아의 승온탈착법 등으로 촉매의 특성을 조사하였다. 아크롤레인의 산화반응에 대한 이 촉매계의 반응특성은 고정층 연속반응기에서 조사하였다. 이 촉매들은 $200^{\circ}C$ 근처에서 결정수의 탈리가 일어났고 구리의 치환에 따른 구조수의 탈리는 $300{\sim}400^{\circ}C$ 사이에서 관찰되었다. 이들 촉매는 Keggin 구조를 가짐을 확인할 수 있었고, 구리의 치환양이 증가함에 따라 Keggin 음이온인 $(PMo_{12}O_{40})^{3-}$의 분해 정도가 증가하였으며, 이때 분해 생성물로 소량의 $MoO_3$와 $P_2O_5$가 관찰되었다. x가 증가할수록 아크롤레인의 전화율이 감소하였는데 이것은 비표면적과 전체 산점의 양이 감소하였기 때문인 것으로 판단된다. 그러나 단위면적당 반응속도와 아크릴산의 선택도는 x=1.0에서 가장 높게 나타났으며 이 촉매는 독특한 산점분포를 나타내었다.
시화지구 인공습지에 식재된 정수식물인 갈대(Phragmites australis)의 관리 방안을 모색하기 위해 갈대에 의한 질소 및 인 흡수 제거 양상과 갈대 생장과 관련된 토양 특성을 조사하였다. 습지 조성 초기에 갈대의 생장은 토양 염농도에 의해 저해된 것으로 나타났으며, 토양 유기물 함량은 갈대 비생육기 동안 고사체의 집적에 의해 증가하였지만, 서서히 분해되어 감소한 것으로 조사되었다. 갈대의 건물중과 질소 및 인 흡수량은 생장기인 여름과 가을에는 증가하였지만, 비생육기인 가을에는 감소하였다. 따라서 생장기 동안 갈대의 흡수에 의해 상당한 양의 질소와 인이 제거되었지만, 비생장기 동안 갈대 고사체의 형태로 토양에 환원되어 미생물의 분해에 의해 영양염류가 재방출될 가능성이 높은 것으로 판단되었다. 본 연구 결과에 의하면 인공습지 조성의 목적인 수질 정화와 생태공원으로서의 기능을 위해서는 갈대를 생육기간 중에 수확하는 방안을 적극적으로 모색해야 될 필요성이 있다.
The aim of present investigation was to clinically measure the thickness of palatal masticatory mucosa in the hard palate as potential donor site for mucogingival surgery, to determine the relation to shape of palatal vault, form of tooth, gender, and to serve the clinical criteria t o choose the proper surgical technique. 84(mean age:25yrs) systemically and periodontally healthy volunteers participated in this study and 18 standard measurement points were defined in the hard palate, located on 3 lies which ran at different distances parallel to the gingival margin. 6 positions were designated on each of these 3 lines between the level of canine and 2nd molar and a bone sounding technique using a periodontal probe with minimal local anesthesia was utilized to assess the thickness of palatal masticatory mucosa. Student t-test was used to determine the difference in mucosal thickness between 2 groups gender, shape of palatal vault (high palatal vault vs. low palatal vault), tooth form (short-wide vs. long narrow) The result of this study were as follows: 1. Soft tissue thickness progressively increased in sites further away from the gingival margin (p<0.01). 2. Depending on position, in line a and line c the masticatory mucosal thickness increased from Ca to M2(p<0.01), but in line b the thickness increased from Ca to P2, and decreased to M1 and increased again to M2. 3. Gender did not influence the thickness of masticatory mucosa. 4. Palatal vault shape was associated with the thickness of masticatory mucosa. Thickness of low palatal vault group was thicker than high palatal group between P2 and M2 position. 5. Form of tooth did not influence the thickness of masticatory mucosa. In conclusion, palatal vault shape was associated with the thickness of masticatory mucosa. So, mucogingival surgery can be considered as a treatment modality in high palatal vault group. But, Gender and tooth form did not influence the thickness of masticatory mucosa.
연속적인 지표 플럭스 관측으로부터 축적되는 엄청난 양의 자료를 체계적으로 처리분석하고 종합하여 일관성 있는 결과를 도출해 내려면 에디 공분산 자료 처리 방법의 표준화가 우선되어야 한다. 이 논문에서는 국내 타워 플럭스 관측 네트워크인 KoFlux의 표준화된 자료 처리 방법을 소개하고, 처리 방법이 다른 경우에 생길 수 있는 지표 플럭스의 불확실성을 평가하였다. 광릉 활엽수림에서 관측된 탄소 플럭스의 경우, 순생태계교환량(net ecosystem exchange, NEE)과 생태계호흡량(ecosystem respiration, Re)은 각각 자료 처리 방법의 차이에 따라 민감한 반응을 보였다. 그러나 두 양이 서로 상쇄되어, 총일차생산량(gross primary productivity, GPP=NEE+Re)은 자료 처리 방법이 다른 경우에도 불구하고 오차 범위 내에서 일치하였다. 이러한 결과는 GPP를 산출할 때에 Re를 독립적으로 관측하는 것이 중요함을 시사한다. 반면 수증기 플럭스(증발산)의 경우, 야간 토양 증발이 작아서 연 적산증발산량은 자료 처리 방법에 민감하지 않았다. 이렇게 표준화된 자료처리 프로토콜을 아시아 타워 플럭스 네트워크인 AsiaFlux에 적용할 경우, 지역 규모 탄소 순환, 역학 식생 및 지면과정 모형의 검증을 위한 일관성 있는 데이터베이스의 구축이 가능해 질 것이다.
본 논문에서는 찬우$\mid$강하법에 의한 접지저항 및 대지첸위 분표의 측캠시 전휴보조전극의 영향에 대하여 기술하였으며, 측정시 오치를 최소화하는 기법을 제안하였다. 전위강해법은 전위와 천류의 측정에 이론적인 비1깅을 두고 있으며, 측정오차는 주로 측정시 설치하는 보조전극의 위치와 자체저항에 기인한다. 피측정 접지전극의 접지저항은 전위강하법에서 전위보조전극을 피측정 접지전극과 전류보조전극이 이루는 일직선상에 위치시킬 때 61.8[%]법칙을 적용하여 측정한다. 하지만 건물이나 포장도로, 구조물 등이 산재해 있는 도심의 경우에는 현장에서 피측정 접지전극과 전류보조전극 사이에 적결한 이격거리 확보가 불가능하거냐 전류보조전극의 접지저행값이 피측정 챔 지전극에 비하여 큰 값을 가지는 경우가 있다. 파측정 접지천극과 전류보조전극을 충분히 이격시키지 않거나 전류류보조전극의 접지저항값이 피측청 접지전극의 접지저항보다 비정상척으로 큰 경우 접지저항의 측정은 오차를 수반하게 되며, 측정된 접지저항값은 오차즐 보정해 주어야 한다. 본 연구애서 측정대상 전극은 길이 2.4[m]의 봉형 접지전극으호 하였으며, 전류보조전극의 영향을 고려할 때 피측정 접지전극과 전류보조전극의 적정한 이격거리는 피측정 접치전극 길이의 5배 이상으로 하여야 전위보조전극을 사설하기가 용이하며 측정정확도의 확보에 유리하다. 또한 전류보존전극의 접지저항값이 피측정 접지전극의 접지저항값 약 36.5배 이하에서는 거의 오차를 발생시키지 않는다.
원자력시설의 해체를 위한 표면오염도를 측정함에 있어 기존의 일반적인 단일층 함침 복합체의 단점을 개선한 치밀한 구조의 지지층 위에 활성층의 2차막을 도포 하여 제조된 이중 구조의 고분자 복합체를 제조하고 이들의 특성을 분석하였다. 세륨활성화된 이트리움실리케이트(Cerium-activated ytttrium silicate, CAYS)를 함침시킨 폴리설폰 이중구조 필름은 1차 지지층으로서 폴리설폰 (polysulfone, PSF)과 메틸렌클로라이드 (methylene chloride, MC)로 이루어진 2액용액을 유리판 위에 제막하고 증발을 통해 MC를 제거하여 고분자의 유리화(vitrification)를 통해 치밀한 구조로 고형화하도록 하였다. 고형화한 1차층 위에 CAYS 와 용매로 이루어진 2차 제막용액을 덧붙여 도포하고 물에 침지시키거나 대기방치를 통해 고형화시켰다. 이렇게 이루어진 2중 구조의 무기섬광체 함침 복합체 필름은 2차 제막층에 손가락 형태의 큰 기공이 생성되었으며, 1차층과 2차층이 완전히 결합되어 있어 우수한 기계적 물성을 나타냈다. 한편, 섬광체인 CAYS를 첨가하였을 때 필름에 생성되는 은 기공의 형성이 증대되는 특성을 보였으며, 용매의 증발에 의해 고형화 된 필름은 치밀한 구조의 형상을 보였다. 제조된 필름들은 방사성핵종의 탐지에 있어 신뢰할만한 탐지 결과를 보였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.