• 한국전산유체공학회:학술대회논문집
• /
• 2008.03b
• /
• pp.205-208
• /
• 2008

The wind load on building surface is numerically investigated. The geometry of target building is a square cross section and aspect ratio (height (H) to width (d)) is 6. On building surface, the pressure was measured, compared to obtained value from numerical simulation. The numerical simulations were done using URANS with three different turbulence models such as v2-f model, k-${\omega}$model, and k-${\varepsilon}$ model, respectively. The v2-f model showed the best agreement with experimental data in simulating mean pressure coefficients on front, rear and side surface. But unsteady characteristics of pressure history measured on surface is shown a discrepancy between experiment and numerical simulation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.2
• /
• pp.42-50
• /
• 1995

This paper proposes a new method to investigate combustion phenomena using the variation of crankshaft speed, From the idea that the variation of crankshaft speed contains the information of combustion, the energy method is applied as a single degree of freedom. Through the comparison of measured and calculated crankshaft speed, the proposed energy model is proved to be effective. When the crankshaft speed is used in the energy equation, filtering of the speed is required. The frequency components of cylinder pressure are analyzed and the coefficients of Fourier series above the twelfth frequency of engine speed are considered as a noise. As an example of application of this research, some combustion analyses like mean effective pressure, heat release rate, and misfire detection were carried out.

• Journal of Ocean Engineering and Technology
• /
• v.11 no.2
• /
• pp.91-99
• /
• 1997

This paper presents theoretical formulations and numerical computations for predicting first-and second-order hydrodynamic force on a ship advvancing in waves. The theoretical formulation leads to linearized radiation and diffration problems solving the three-dimensional Green function integral equations over the mean wetted body surface. Green function representing a translating and pulsating source potantial for infinite water depth is used. In order to solve integral equations for three dimentional flows using Green function efficiently, the Hoff's method is adopted for numerical calculation of the Green function. Based on the first-order solution, the mean seconder-order forces and moments are obtained by directly integrating second-order pressure over the mean wetted body surface. The calculated items are carried out for analyzing the seakeeping characteristics of Series 60. The calculated items are hydrodynamic coefficients, wave exciting forces, frequency response functions and addd resistance in waves.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1993.10a
• /
• pp.13-20
• /
• 1993

The sorption equilibria and permeation rates for carbon dioxide in such glassy polymer membranes with high glass-transition temperature as polyimide, polyetherimide, polysulfone and polyethersulfone membranes, were measured. The sorption isotherms for these systems can be described well by the dual-mode sorption model, whereas the pressure dependences of the mean permeability coefficients are simulated better by a modified dual-mode mobility model than the conventional dual-mode mobility model in which the Henry's law and Langmuir populations execute four kinds of diffusive movement.

• Korean Journal of Adult Nursing
• /
• v.21 no.1
• /
• pp.95-104
• /
• 2009

Purpose: To examine pressure ulcer care from the standpoints of perceived importance, educational needs, knowledge and performance among clinical nurses. Methods: This descriptive study was conducted with a convenient sample of 289 nurses from four hospitals. Questionnaire data collected from June to August 2008 was analyzed using descriptive statistics, t-test, ANOVA, and Pearson's correlation coefficients. Results: The mean scores of importance and educational needs concerning pressure ulcer care were high, performance was moderate, and knowledge was low. Knowledge level differed significantly according to career, performance differed significantly according to pressure ulcer care education and the main healer(the person primarily responsible for treatment). Perceived importance differed significantly according to the main healer, and educational needs differed significantly according to working area and the main healer. Significant correlations were evident between performance and importance, performance and educational needs, importance and knowledge, and importance and educational needs. Conclusion: Focus on perceived importance and educational needs to clinical nurses about pressure ulcer care may be beneficial to improve knowledge and practice of pressure ulcer care, and should be reflected in the development of effective programs to enhance relevant nursing skills.

• Wind and Structures
• /
• v.23 no.3
• /
• pp.231-251
• /
• 2016

This paper presents the experimental results of the wind tunnel tests for three symmetric, rectangular, tall building models on a typical open terrain considering the torsional motion-induced vibrations. The time histories of the wind pressure on these models under different reduced wind speeds and torsional amplitudes are obtained through the multiple point synchronous scanning pressure technique. Thereafter, the characteristics of both the Root Mean Square (RMS) coefficients and the spectra of the base shear/torque in the along-wind, across-wind, and torsional directions, respectively, are discussed. The results show that the RMS coefficients of the base shear/torque vary in the three directions with both the reduced wind speeds and the torsional vibration amplitudes. The variation of the RMS coefficients in the along-wind direction results mainly from the change of the aerodynamic forces, but sometimes from aeroelastic effects induced by torsional vibration. However, the variations of the RMS coefficients in the across-wind and torsional directions are caused by more equal weights of both the aerodynamic forces and the aeroelastic effects. As such, for the typical tall buildings, the modification of the aerodynamic forces in the along-wind, across-wind, and torsional directions, respectively, and the aeroelastic effects in the across-wind and torsional directions should be considered. It is identified that the torsional vibration amplitudes and the reduced wind speeds are two significant parameters for the aerodynamic forces on the structures in the three directions.

• Journal of Mechanical Science and Technology
• /
• v.20 no.3
• /
• pp.399-408
• /
• 2006

Nucleate pool boiling heat transfer coefficient (HTCs) were measured with one nonazeotropic mixture of propane/isobutane and two azeotropic mixtures of HFC134a/isobutane and propane/HFC 134a. All data were taken at the liquid pool temperature of $7^{\circ}C$ on a horizontal plain tube of 19.0mm outside diameter with heat fluxes of $10\;kW/m^2\;to\;80kW/m^2$ with an interval of $10\;kW/m^2$ in the decreasing order of heat flux. The measurements were made through electrical heating by a cartridge heater. The nonazeotropic mixture of propane/isobutane showed a reduction of HTCs as much as 41% from the ideal values. The azeotropic mixtures of HFC134a/isobutane and propane/HFC134a showed a reduction of HTCs as much as 44% from the ideal values at compositions other than azeotropic compositions. At azeotropic compositions, however, the HTCs were even higher than the ideal values due to the increase in the vapor pressure. For all mixtures, the reduction in heat transfer was greater with larger gliding temperature difference. Stephan and Korner's and lung et al's correlations predicted the HTCs of mixtures with a mean deviation of 11%. The largest mean deviation occurred at the azeotropic compositions of HFC134a/isobutane and propane/HFC134a.

• Wind and Structures
• /
• v.30 no.1
• /
• pp.55-67
• /
• 2020

Wind tunnel test is one of the most important means to study the flutter performance of bridges, but there are blockage effects in flutter test due to the size limitation of the wind tunnel. On the other hand, the size of computational domain can be defined by users in the numerical simulation. This paper presents a study on blockage effects of a simplified box girder by computation fluid dynamics (CFD) simulation, the blockage effects on the aerodynamic characteristics and flutter performance of a long-span suspension bridge are studied. The results show that the aerodynamic coefficients and the absolute value of mean pressure coefficient increase with the increase of the blockage ratio. And the aerodynamic coefficients can be corrected by the mean wind speed in the plane of leading edge of model. At each angle of attack, the critical flutter wind speed decreases as the blockage ratio increases, but the difference is that bending-torsion coupled flutter and torsional flutter occur at lower and larger angles of attack respectively. Finally, the correction formula of critical wind speed at 0° angle of attack is given, which can provide reference for wind resistance design of streamlined box girders in practical engineering.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.5 s.170
• /
• pp.181-188
• /
• 2005

The purpose of this study is to develop the new cuff improving the accuracy of blood pressure measurement, and to evaluate the performance of the developed system. We added a small bladder to the normal cuff which is called the double bladder system. The developed system for blood pressure measurement was based on the oscillometric method using a double bladder. This system was developed in order to reduce the oscillation noise and to amplify the signal of pure blood pressure An oscillometric signal database based on the developed system were evaluated following the standard ANSI/AAMI/SP10-1992. The correlation coefficients between cuff of double bladder and normal cuff were 0.98 for systolic and 0.94 for diastolic. Mean differences and the standard deviations between average blood pressure of mercury sphygmomanometer and automated sphygmomanometer were -0.7mmHg and 4.9mmHg for systolic, and -1.4mmHg and 5.4mmHg for diatolic, respectively. We conclude that the proposed double bladder based cuff system improves the accuracy of the oscillometric blood pressure measurement. The developed system reduces the error range about $44\~62\%$ for systolic and about $6\~21\%$ for diastolic compared to the recently developed commercially available sphygmomanometers.

• Fibers and Polymers
• /
• v.1 no.1
• /
• pp.59-65
• /
• 2000

In order to investigate psychoacoustic characteristics of fibers, and to compare them with sound physical parameters, each sound of 25 different fabrics consisted of a single fiber such as wool, cotton, silk, polyester, and nylon was recorded. Sounds of specimens were transformed into critical band diagram and psychoacoustic characteristics including loudness and sharpness for each sound were calculated based on Zwicker＇s models. Physical parameters such as the level pressure of total sound (LPT), level ranges (ΔL), frequency differences (Δf), AR coefficients (ARC, ARF, ARE) were obtained in fast fourier transform (FFT) spectrum. Nylon taffeta showed higher values for loudness than 2.5 sone corresponding to human low conversation, while most silk fibers generated less louder showing lower values for loudness than 1.0 sone. Wool fibers had higher loudness mean value than that of cotton, while the two fibers didn't differ in LPT. Loudness showed high positive correlation coefficients with both LPT and ARC. Sharpness values were higher for wool fiber group than other fibers. Sharpness was not concerned with loudness, LPT, and ARC, but the fabrics with higher values for sharpness tended to show higher ΔL.