• 대한기계학회논문집
• /
• 제14권2호
• /
• pp.358-366
• /
• 1990

As a basic study to clarify the scoring resistance in lubricated sliding contact, the temperature rise on frictional surface was analyzed by theoretical method and the effects of various factors on the temperature rise were examined. On the basic of the results obtained theoretically, the practical equations to calculate the maximum average temperature of the contact surface were proposed which are applicable to sliding contact. Then, the effects of sliding velocity and oil temperature on the seizure behavior, and the relation between seizure and temperature rise were investigated. The following conclusions are deduced : The maximum average temperature rise and the other bulk temperature. The former is affected by the size of heat supply region and the sliding velocity, the latter is affected by heat transfer coefficient. Without regard to the operating condition such as sliding velocity, oil temperature and operating time at each load-step, the maximum average temperature just before seizure is nearly constant except in the region of lower velocity. Consequently, the maximum average temperature of the contact surface in boundary lubrication is a useful criterion to predict the scoring of sliding contact.

• Journal of Electrical Engineering and Technology
• /
• 제13권2호
• /
• pp.800-811
• /
• 2018

This paper presents a regenerative braking control scheme for Switched Reluctance Machine (SRM) drive in Electric Vehicles (EVs). The main purpose is to maximize the recovered energy during battery charging by taking into account the nonlinear physical characteristics of the Switched Reluctance Machine. The proposed regenerative braking method employs the back-EMF in the generation process as a complicated position-dependent voltage source. The proposed maximum power recovery (MPR) operation of the regenerative braking is first based on the maximization of the extracted power from the machine and then the maximization of the power transferred to the battery. The maximum power extraction (MPE) from SRM is based on maximizing the energy conversion ratio by the calculation of the optimum PWM switching duty cycle, turn-on, and turn-off angles. By using the impedance matching theorem that allows the maximum power transfer (MPT) of the MPE, the proposed MPR is achieved. The parametric averaged value modeling of the machine phase currents in the chopping control mode is used for MPR realization. By following this model, a nonlinear equivalent input resistance is derived for the battery internal resistance matching. The effectiveness of the proposed regenerative braking method is demonstrated through simulation results and experimental implementation.

• 대한토목학회논문집
• /
• 제33권2호
• /
• pp.465-473
• /
• 2013

본 연구에서는 터널에서 발생되는 화재로부터 구조물을 보호하기 위해 내화패널이 부착된 프리캐스트 PSC 슬래브의 내화성능을 조사하기 위해 내화실험이 수행되었다. 내화실험은 독일의 RABT(Richtlinien fur die Ausstatung und den Betrieb von stra${\beta}$entunneln) 화재시간-온도곡선을 적용하여 내화성능을 평가하는 것으로 하였다. ITA(2004)에서 제시하는 기준에 따라 내화성능 시험을 수행한 결과, 콘크리트의 손상을 판단하는 위치인 t=0mm의 최대온도는 $367^{\circ}C$로서 손상한계온도 $380^{\circ}C$(ITA 2004)이하였으며, 철근의 손상을 판단하는 위치인 t=25mm의 최대온도는 $239^{\circ}C$로서 손상 한계온도인 $250^{\circ}C$이하로 나타났다. 실험결과로부터, 25mm두께의 내화패널이 부착된 프리스트레스 슬래브 시험체는 내화성능을 가진 것으로 입증되었다.

• 전기학회논문지P
• /
• 제66권4호
• /
• pp.219-223
• /
• 2017

In this paper, we calculated the losses in the high voltage lines of power distribution system. The losses caused by high voltage lines are calculated using maximum current, resistance, loss factor, and dispersion loss factor. The accurate extraction of these factors are very important to calculate the losses exactly. Thus, the maximum loads are subdivided to regions and calculated monthly for more accurate maximum current calculation. Also, the composite resistance is calculated according to the ratio of the used wire types. In order to calculate the loss factor, the load factors according to the characteristics of each region were calculated. Finally, the losses of the distribution system is calculated by adding the losses by the transformers and the low voltage lines.

• Journal of Electrical Engineering and Technology
• /
• 제8권5호
• /
• pp.1221-1226
• /
• 2013

In this paper, the equivalent circuit for the efficiency calculation by precise estimation of the linkage flux, inductance and iron loss resistance was calculated accurately. In addition, the driving characteristics according to the current phase angle are analyzed and the maximum efficiency point is calculated. And then, analyzed and experimental values of the efficiency were compared. So, causes of error were expected to be vibration and noise by harmonic distortion of the voltage and current, and mechanical loss of dynamometer. In addition, the driving characteristics according to the current phase angle are analyzed and the maximum efficiency point is calculated.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권8호
• /
• pp.382-386
• /
• 2001

Presently, typical maximum probe spacing of soil resistivity survey(Wenners 4 pin method) is 20 m in case of 154 K substation grounding design of KEPCO. This paper examined the effects of maximum probe spacing of wenner method on the equivalent soil modeling and the accuracy of grounding resistance measurement by comparing the calculated FOP(Fall-of-Potential) curves of various soil models with the measured one at 154kV H substation. The comparison results showed that the inaccurate estimation of deep soil resistivity, which is caused from the short probe spacing of soil resistivity survey, can produce large errors on measurement of grounding resistance. In this paper a quantitative analysis of FOP at H substation has been presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 학술대회 논문집 전문대학교육위원
• /
• pp.162-166
• /
• 2000

In this paper, a maximum efficiency control technique of real-time processing in which parameter variation is compensated in vector control of an induction motors(I.M.) is proposed. Based on equivalent model of I.M., a loss minimization factor(LMF) with the variations of speed is derived. To solve problem of inaccuracy of LMF curves due to machine parameter variation, rotor resistance estimation is performed by using instantaneous reactive power. The estimated rotor resistance values are applied to the maximum efficiency control with a LMF.

• Journal of Electrical Engineering and Technology
• /
• 제8권1호
• /
• pp.110-117
• /
• 2013

Maximum Torque Per Amp (MTPA) control for induction motor drives seeks to achieve a desired torque with the minimum possible stator current. This is favorable in terms of inverter operation and nearly optimal in terms of motor efficiency. However, rotor resistance variation can cause significant performance degradation. This work demonstrates that existing MTPA controls perform sub-optimally as temperature varies. An adaptive MTPA control strategy is proposed that always achieves optimal performance without exhibiting hunting phenomenon regardless of rotor temperature. The proposed control is experimentally shown to accurately achieve the desired torque.

• 대한설비공학회지:설비저널
• /
• 제8권1호
• /
• pp.1-9
• /
• 1979

Heat transfer characteristics of an annular heat pipe is investigated theoretically and experimentally. An annular heat pipe transports maximum heat which is found to be a cubic polynomial function of the thickness of annulus when the annulus becomes large, maximum heat transfer rate Is limited by boiling criterion. The limit decreases inversely proportional to the thickuess of annulus. Theoretical formula for thermal resistance of annular heat pipe Is proposed. Experimental results on the maximum heat transfer rate satisfactorily agree with theory. Measured thermal resistance is found to be lower than the predicted results as the thickness of annulus becomes large.

• 한국표면공학회지
• /
• 제28권5호
• /
• pp.289-299
• /
• 1995

The effects of phosphate coating have been studied on physical properties and corrosion resistance of painted aluminum alloy sheet for automobile body. The physical properties (surface roughness, paint adhesion, impact resistance and pencil hardness) and corrosion resistance(cyclic corrosion and filiform corrosion) were investigated. Phosphate coatings enhanced the physical properties of painted Al alloy sheet, especially paint adhesion after the 240hours water immersion test. Phosphate coating also markedly improved the resistance for cyclic corrosion and filiform corrosion of painted cold rolled steel and Zn-Ni plated steel sheet as well as painted Al alloy sheet. The corrosion resistance of painted Al sheets was varied with the concentration of free fluoride ion and metal additives like Ni and Mn in the phosphating bath. A maximum corrosion resistance was obtained at about 300ppm of fluoride ion and additives of Ni and Mn obviously increased the corrosion resistance of painted specimens.