• Journal of Welding and Joining
• /
• v.14 no.6
• /
• pp.37-47
• /
• 1996

An ultrasonic testing uses the directivity of the ultrasonic wave which propagates in one direction. The directivity is expressed as the relationship between the propagate direction and its sound pressure. The directivity of ultrasonic wave is related to determination of testing sensitivity, scanning pitch and defect location. This paper investigated the directivity of ultrasonic wave, which scattered from slit defect located in heat-affected zone (HAZ) in butt joint using visualization method. The directivity of shear waves scattered from slit defect were different according to probe direction (far defect, near defect) and probe position (forward movement, maximum echo position, backward movement). The difference of directivity of reflection wave was existed between 2 MHz and 4 MHz angle probes. In the case of 2 MHz angle probe, the directivity of reflection wave was appeared sharp form because of the relation wave length and defect size.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.8
• /
• pp.872-879
• /
• 2010

This paper describes the design for radiation pattern directivity of vehicle license plate RFID tag antenna to improve the readable range. Directivity pattern of the proposed passive antenna is decided by the meander line position and the bumper size attached to the tag antenna. In order to prove the verification of the calculated directivity pattern and readable range of the proposed antenna, the tag antenna has been fabricated and measured at the anechoic chamber. It is shown that the maximum directivity gain of the measured radiation pattern of active and passive tag antenna were observed 2.32 dBi and 3.1 dBi, respectively. The maximum readable range of passive tag antenna was measured about 8.5 m at ${\pm}45^{\circ}$ beam direction on the basis of the driving car direction($0^{\circ}$ of azimuth angle).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1995.11a
• /
• pp.202-204
• /
• 1995

An acoustic sensor using PVDF film is proposed in this paper. And its properties, such as sensitivity level, identification of sound source frequencies. and directivity, were experimented. Sensitivity level measured at the distance of 1[m] was limited in the range of ${\pm}$10dB. Adjacent three frequencies were also tested to identify the frequency of sound sources. In the range of audible frequencies, it could distinguish the frequencies of a complex sound. In addition, it was found that the sensor outputs were maximum in the coincided direction with a source, when directivity was experimented with three sound sources and FFT. The proposed PVDF film sensor has good characteristics of directivity and identifying ability as an acoustic sensor.

• Structural Engineering and Mechanics
• /
• v.56 no.5
• /
• pp.855-870
• /
• 2015

In this paper the effects of fling-step and forward-directivity on the seismic performance of steel eccentrically braced frames (EBFs) are addressed. Four EBFs with various numbers of stories (4-, 8-, 12- and 15-story) were designed for an area with high seismic hazard. Fourteen near-fault ground motions including seven with forward-directivity and seven with fling-step effects are selected to carry out nonlinear time history (NTH) analyses of the frames. Furthermore, seven more far-field records were selected for comparison. Findings from the study reveal that the median maximum links rotation of the frames subjected to three set of ground motions are in acceptable range and the links completely satisfy the requirement stated in FEMA 356 for LS performance level. The arrival of the velocity pulse in a near-fault record causes few significant plastic deformations, while many reversed inelastic cycles result in low-cycle fatigue damage in far-fault records. Near-fault records in some cases are more destructive and the results of these records are so dispersed, especially the records having fling-step effects.

• Earthquakes and Structures
• /
• v.17 no.1
• /
• pp.1-15
• /
• 2019

In the structures with high level of ductility, the earthquake energy dissipation in structural components is an important factor that describes their seismic behavior. Since the connection details play a major role in the ductile behavior of structure, in this paper, the seismic response of 3-, 5- and 8-story steel special moment frames (SMFs) is investigated by considering the effects of panel zone modeling and the influence of forward-directivity near-field ground motions. To provide a reasonable comparison, selected records of both near and far-field are used in the nonlinear time-history analysis of models. The results of the comparison of the median maximum inter-story drift under excitation by near-field (NF) records and the far-field (FF) ground motions show that the inter-story drift demands can be obtained 3.47, 4.86 and 5.92 times in 3-, 5- and 8-story structures, respectively, undergoing near-field earthquakes.

• Steel and Composite Structures
• /
• v.38 no.6
• /
• pp.671-690
• /
• 2021

Seismic responses of RC core wall with two outriggers are investigated in this study. In the models analyzed here, one of the outriggers is fixed at the top of the building and the second is placed at different levels along the height of the system. Each of the systems resulting from the placement of the outrigger at different locations is designed according to the prescriptive codes. The location of the outrigger changes along the height. Linear design of all the structures is accomplished by using prescriptive codes. Buckling restrained braces (BRBs) are used in the outriggers and forward directivity near fault and far fault earthquake record sets are used at maximum considered earthquake (MCE) level. Results from nonlinear time history analysis demonstrate that BRB outriggers can change the seismic responses like force distribution and deformation demand of the RC core-walls over the height and lead to the new plastic hinge arrangement over the core-wall height. Plasticity extension in the RC core wall occurs at the base as well as adjacent to the outrigger levels. Considering the maximum inter-story drift ratio (IDR) demand as an engineering parameter, the best location for the second outrigger is at 0.75H, in which the maximum IDR at the region upper the second outrigger level is approximately equal to the corresponding value in the lower region.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.719-722
• /
• 2002

This paper reports the characteristics of a bidirectional antenna by using a planar array of a probe excited circular ring. The element of a bidirectional antenna is first designed to achieve the maximum directivity. The directivity can be further increased by arranging these elements to form the linear array. There are two types of linear array to be investigated i.e., on axis and off axis arrangement. On-axis linear array yields better directivity than off-axis linear array. Therefore, this orientation is further used to form the planar array. The radiation characteristics of this optimum planar array are rigorously reported. The proposed structure is very useful to extend the distance between the base station in PCT system.

• Earthquakes and Structures
• /
• v.7 no.6
• /
• pp.1259-1281
• /
• 2014

This research has been conducted in order to investigate the effects of peak ground velocity (PGV) of near-field earthquakes on base-isolated structures mounted on Single Friction Pendulum (SFP), Double Concave Friction Pendulum (DCFP) and Triple Concave Friction Pendulum (TCFP) bearings. Seismic responses of base-isolated structures subjected to simplified near field pulses including the forward directivity and the fling step pulses are considered in this study. Behaviour of a two dimensional single story structure mounting on SFP, DCFP and TCFP isolators investigated employing a variety range of isolators and the velocity (PGV) of the forward directivity and the fling step pulses as the main variables of the near field earthquakes. The maximum isolator displacement and base shear are selected as main seismic responses. Peak seismic responses of different isolator types are compared to emphasize the efficiency of each one under near field earthquakes. It is demonstrated that rising the PGVs increases the isolator displacement and base shear of structure. The effects of the forward directivity are greater than the fling step pulses. Furthermore, TCFP isolator is more effective to control the near field effects than the other friction pendulum isolators are. This efficiency is more significant in pulses with longer period and greater PGVs.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.4
• /
• pp.267-271
• /
• 2018

A high directivity TIR (total internal reflection) lens in the UV-A region was designed using a silicone resin, and a UV light source module with a maximum irradiation density of $150mW/cm^2$ was fabricated. The beam angle of the TIR lens was designed to be $8.04^{\circ}$ and the maximum diameter of the TIR lens was Ø13.5. A silicone resin having a UV transmittance of 93% and a refractive index of 1.4 at a wavelength of 365 nm was used, and the lens was manufactured using an aluminum mold, from which silicone could be easily released. The module was fabricated in a metal printed circuit board of COB (chip on board) type using a $0.75{\times}0.75mm^2$ UV chip. A jig was used to adjust the focal length between lens and chip and to fix the position of the lens. The optical characteristics such as illumination distributions of the lens and module were designed using 'LightTools' optical simulation software. The heat dissipation system was designed to use a forced-air cooling method using a heat-sink and fan.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.6 no.1
• /
• pp.83-90
• /
• 2010

DTNs (Delay Tolerant Networks) refer to the networks that can support data transmission in the extreme networking situations such as continuous delay and no connectivity between ends. DTMNs (Delay Tolerant Networks) are a specific range of DTNs, and its chief considerations in the process of message delivery in the routing protocol are the transmission delay, improvement of reliability, and reduction of network loading. This article proposes a new LCN (Largest Common Neighbor) routing algorism to improve Spray and Wait routing protocol that prevents the generation of unnecessary packets in a network by letting mobile nodes limit the number of copies of their messages to all nodes to L. Since higher L is distributed to nodes with directivity to the destination node and the maximum number of common neighbor nodes among the mobile nodes based on the directivity information of each node and the maximum number of common neighbor nodes, more efficient node transmission can be realized. In order to verify this proposed algorism, DTN simulator was designed by using ONE simulator. According to the result of this simulation, the suggested algorism can reduce average delay and unnecessary message generation.