• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1C
• /
• pp.34-42
• /
• 2007

The sphere decoder (SD) has recently been proposed to perform maximum likelihood (ML) decoding for multi-input multi-output systems. Employing a 'breadth-first' searching algorithm for closet points in a lattice, we propose a novel ML decoding scheme for multi-input multi-output systems. Simulation results show that the proposed scheme has the same bit error rate performance as the conventional ML decoders while allowing significantly lower computational burden than the SD.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.22 no.1
• /
• pp.1-5
• /
• 1986

In order to improve the net-mouth height of dragged gears, the authors devised models of floatingcollars of nylon cloth instead of floats and experimented with 4 types-A type (length 65em, breadth 3em), B type (length 65em, breadth 4em), C type (length 65em, breadth 5em) and D type (length 65 em, breadth 6em) attached respectively to the front edge of square of a model net after preliminary experimentation. These various types of floating collars were experimented in a circulating water channel to evaluate the characteristics of net-mouth height and hydrodynamic resistance and the effect of the length of bridles were also examined. The results obtained were as follows: 1. In case of attaching floats, the model net-mouth height reduced from 80 em to 20 em when current velocity was increased from 0.25m/see to 1m/sec. 2. In case of attaching floating collars, the model net-mouth heights were maintained 70 em, 71 em, 80 em, 78 em in maximum and 55 em, 63 em, 69 em, 73 em in minimum respectively even the current volocity was increased from 0.25 m/see to 1 m/see. 3. The model net-mouth height was reduced to 10 em maximum according to the current velocity and types of floating collars when the bridles were shortened 3~4 mm in length. 4. Hydrodynamic resistance of D type only was increased to 700 g in maximum and those of A, B, C type were reduced to 460 g in maximum at current velocity beyond 0.5 m/ see when bridles were shortened 3-4 mm in length. 5. But the model net-mouth heights became higher in accordance with breadth of floating coliars, B type was the best for this model net in case that hydrodynamic resistance was taken into account.

• Journal of Ocean Engineering and Technology
• /
• v.8 no.1
• /
• pp.114-122
• /
• 1994

X-ray stress constant, K, was determined for the diffraction line of (211)plane by using Cr-K$\alpha$ radiation. K was -340.87 MPa/deg. Fatigue crack propagation tests of SS41 steel were conducted under stress ratios of 0.1, 0.3 and 0.5. The half-value breadth of X-ray diffraction profile was measured at and beneath the fracture surface. The half-value breadth, B, on the fracture surface was found to increase with increasing $K_max$. The value of B was influenced by stress ratio in SS41 steel. The half-value breadth took the maximum value at the borden of reversed plastic zone, while it approached to the initial (pre-fatigue) value near the boundary of monotonic plastic zone. The maximum depth of the plasticzone was evaluated on the basis of the half-value breadth distribution. The depth $\omega$$_y$ is related to $K_max$by the following equation : $\omega$$_y$ = $\alpha$($K_max$/$\sigma$$_y$$)^2$ where .sigma.$\sigma$$_y$ is the yield strength obtength obtained in tension test .alpha.is 0.136 for SS41 steel.

• Journal of Sasang Constitutional Medicine
• /
• v.8 no.1
• /
• pp.101-186
• /
• 1996

The clinical application of constitutional Diagnosis is the most important part of Sasang constitutional medicine. It has been studied in various way. However, the study of morphologic characteristics on the face is applied for the first time. For quantitative analysis of the correlation between the sasang constitution and the shape of the face, the head-facial part of 170 cases were measured by Martin's measurement and analysis of a) the measurement value of height and the component ratio from the Gnathion to each part of face by constitution. b) the measurement value of depth and the component ratio from T-projected to each part of the face by constitution. c) the measurement value of breadth and component ratio between each parts of the facial breadth by constitution. d) the ratio of square on every part of face by constitution. e) the characteristics on each part of the face by constitution. f) the contour line of the forehead. g) the result of discriminant analysis about the constitution. Authors obtained the results from the study as follows; 1. The characteristics of Taeum-IN (1) The measurement value of Height, Breadth, T-Projected had a tendency to maximum value in general. (2) The value of lower opthal height and the square of lower opthal part was maximum. (3) The value of Pronasal T-projected length and Subnasal T-projected length was minimum, so Taeum-In has characteristics of depression in middle face, nasal part. (4) In the ratio of Breadth, T-Projected, T-Projected was minimum. (5) It was maximum that the square of nose, Alare, Middle face, Lower face and it was minimum that the square of eye. The square of nose, Alare, Middle facc, Lower face was maximum and the square of eye was minimum. (6) The curvature of the eyebrow was minimum. (7) The projection of jaw (Pogonion T-projection length) was maximum. (8) The breadth of eye was minimum. (9) There was a tendency that the projection of the forehead to the right in general. 2. The characteristics of Soeum-In (1) In all cases of projected length the measurement value was minimum. (2) The value of lower opthal height and the square of lower opthal part was minimum. (3) By the Pupulare T-projected length, the value of Pronasal T-projected length and Subnasal T-projected length was minimum, so the Soeum In's face shape is flat. (4) The square of eye, mouth, forehead was maximum and the square of nose, Alare, Middle face, Lower face was minimum. (5) The curvature of the eyebrow was maximum. (6) The projection of mouth was minimum. (7) The jaw was flat. (8) The breadth of eye was maximum. (9) There was a tendency that the projection of the forehead to the left in general. 3. The characteristics of Soyang-In. (1) In most cases of 고경 length the measurement value was minimum. (2) By the Pupulare T-projected length, each ratio of projected length was maximum, so the Soyang-In's face shape has many protrusions (3) In the ratio of Breadth, T-Projected, T-Projected was maximum. (4) The square of mouth was minimum. (5) The inclination of the forehead was minimum. (6) The projection of mouth was maximum. (7) The breadth of eye was minimum. (8) There was a tendency that the projection of the forehead to the left in general. (9) The middle face was protruded. 4. Discriminant about the constitution. According to the result of discriminant, the accuracy probability of discriminant was 85.58% in total and Taeum-In was 90.5%, Soeum-In was 70.8%, Soyang-In was 89.5%. The accuracy probability of discriminant about 3 constitutional group increased by 49.03% than the accident probility 36.55% 5. Suggestion (1) The study which gather and analysis the data should be continued. (2) The study which subdivide the characteristics of each part of the face by the constitution should be continued. (3) The analysis method about Moire should be supplement. (4) The study about the morphologic characteristics of the whole body should be continued. (5) Computer program of constitution diagnosis should be developed. (6) To increase utility of this method, the measurement should be automation.

• Journal of Ocean Engineering and Technology
• /
• v.16 no.3
• /
• pp.54-58
• /
• 2002

This study investigates a relationship between fracture mechanics parameters (Stress Intensity Factor Range: ΔK, Maximum Stress Intensity Factor; Kmax) and X-ray parameters (residual stress:$\sigma$r half-value breadth: B) for SG365 steel at elevated temperature up to 30$0^{\circ}C$. The fatigue crack propagation test were carried out and X-ray diffraction technique according to the direction of crack length was applied to fatigue fractured surface. The residual stress on the fracture surface was found to increase at low ΔK region, to reach a maximum value at a certain value of Kmax or ΔK and then to decrease. Residual stress was independent of stress ratio by arrangement of ΔK and half value breadth were independent of the arrangement of Kmax. The equation of $\sigma$r-ΔK was established by the experimental data. therefore, fracture mechanics parameters could be estimated by the measurement of X-ray parameters.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.4
• /
• pp.117-123
• /
• 2002

X-ray diffraction observation of fracture surfaces yields useful information to analyze the causes of failure accidents of engineering structures. This experimental technique, named X-ray fractography, has been developed especially in metal and mechanical engineering fields. The distributions of the residual stress and the half value breadth of diffraction profiles beneath the fatigue fracture surface were measured with SNCM 439, HT100 and Ti-6Al-4V alloy. The size of the maximum plastic zone was successfully determined on the basis of the measured distributions. This size was correlated to maximum stress intensity factor. The distributions of the half value breadth of diffraction profiles on the fatigue fracture surfaces were measured with SNCM 439. HT100. The equations of x-ray parameter distribution were possible to estimated fracture parameters of fatigue fracture surfaces.

• Korean Journal of Agricultural and Forest Meteorology
• /
• v.15 no.3
• /
• pp.153-160
• /
• 2013

This study was conducted to investigate the effect of ecological factors affecting Pinus densiflora forest distribution associated with climate change in the future. Ecological niche is used as a method to quantify the position occupied in biological communities, space, influence and all ecological factors. Ecological niche breadth was analyzed on meteorological and growth factors of P. densiflora. Nine sites (i.e., Gangneung, Jeongseon, Pyeongchang, Hamyang, Bonghwa, Yeongyang, Uljin, Uiseong and Boseong) were selected to set $20m{\times}20m$ quadrat from September to October 2010. The height, DBH, clearlength, crown width and basal area were measured at each quadrat and used as growth factors. In addition, the measured values from the closest weather stations of each survey area of the maximum, mean and minimum temperature, humidity and precipitation were used as meteorological factors. The ecological niche breadth of the five meteorological factors except humidity was low. It is considered that precipitation could effect on the distribution of P. densiflora forest. In particular, maximum temperature showed low ecological niche breadth less than 0.4 in most of the survey areas. However, the ecological niche breadth of the five growth factors was high in all survey areas.

• Journal of KIISE:Computer Systems and Theory
• /
• v.37 no.1
• /
• pp.27-34
• /
• 2010

Web crawlers are fundamental programs which iteratively download web pages by following links of web pages starting from a small set of initial URLs. Previously several web crawling orderings have been proposed to crawl popular web pages in preference to other pages, but some graph search techniques whose characteristics and efficient implementations had been studied in graph theory community have not been applied yet for web crawling orderings. In this paper we consider various graph search techniques including lexicographic breadth-first search, lexicographic depth-first search and maximum cardinality search as well as well-known breadth-first search and depth-first search, and then choose effective web crawling orderings which have linear time complexity and crawl popular pages early. Especially, for maximum cardinality search and lexicographic breadth-first search whose implementations are non-trivial, we propose linear-time web crawling orderings by applying the partition refinement method. Experimental results show that maximum cardinality search has desirable properties in both time complexity and the quality of crawled pages.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.9
• /
• pp.782-791
• /
• 2013

This paper proposes the location estimation techniques of distributed targets with the multi-sensor data perceived through IR sensors of the military robots. In order to match up targets with measured azimuths, we apply the maximum likelihood (ML), depth-first, and breadth-first tree search algorithms, in which we use the measured azimuths and the number of pixels on IR screen for pruning branches and selecting candidates. After matching up targets with azimuths, we estimate the coordinate of each target by obtaining the intersection point of the azimuths with the least square error (LSE) algorithm. The experimental results show the probability of missing target, mean of the number of calculating nodes, and mean error of the estimated coordinates of the proposed algorithms.

• Journal of Sasang Constitutional Medicine
• /
• v.11 no.2
• /
• pp.195-207
• /
• 1999

1. PURPOSE This research is a study on constitutional diagnosis through the external appearances, and for finding shape differences of the hand and foot according to the Sasang Constitution. 2. Method We collected 148 person who were healthy and measured length, breadth, circumference and thickness of their hands and feet with 'The Measurement of R. Martin'. We analyzed shape differences of hand and foot according to the Sasang Constitution and made a certain conclusion. 3. Results and Conclusions We got the morphologic characteristics of hand and foot according to the Sasang Constitution. (1) The physical characteristics. The weight is heaviest in Taeumin. (2) The morphologic characteristics of Hand. (1) The wrist circumference is longest in Taeumin. (2) The finger length / hand length(ratio) is higher Soeumin than Taeumin. (3) The wrist breadth is largest in Taeumin(only male). (4) The wrist breadth is larger Taeumin than Soeumin(only female). (5) The palm length is longer Taeumin than Soyangin(only male). (6) The maximum hand breadth is larger Taeumin than Soeumi (only male). (7) The 2nd, 3rd and 4th finger length is longer Soeumin than Soyangin(only male). (3) The morphologic characteristics of Foot. (1) The foot thickness is thickest in Taeumin. (2) The foot breadth is largest in Taeumin. (3) The ankle circumference is longest in Taeumin(only male).