• Composites Research
• /
• v.15 no.4
• /
• pp.23-31
• /
• 2002

The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• Investigative Magnetic Resonance Imaging
• /
• v.1 no.1
• /
• pp.114-118
• /
• 1997

Purpose: Functional MR imaging is the method of demonstrating changes in regional cerebral blood flow produced by sensory, motor, and any other tasks. Functional MR of visual cortex is performed as a patient stares a photic stimulation, so adaptable photic stimulation is necessary. The purpose of this study is to evaluate whether the size of photic stimulator can affect the degree of visual cortex activation. Materials and Methods: Functional MR imaging was performed in 5 volunteers with normal visual acuity. Photic stimulator was made by 39 light-emitting diodes on a plate, operating at 8Hz. The sizes of photic stimulator were full field, half field and focal central field. The MR imager was Siemens 1.5-T Magnetom Vision system, using standard head coil. Functional MRI utilized EPI sequence (TR/TE= 1.0/51. Omsec, matrix $No.=98{\times}128$, slice thickness=8mm) with 3sets of 6 imaging during stimulation and 6 imaging during rest, all 36 scannings were obtained. Activation images were obtained using postprocessing software(statistical analysis by Z-score), and these images were combined with T-1 weighted anatomical images. The activated signals were quantified by numbering the activated pixels, and activation a index was obtained by dividing the pixel number of each stimulator size with the sum of the pixel number of 3 study using 3 kinds of stimulators. The correlation between the activation index and the stimulator size was analysed. Results: Mean increase of signal intensities on the activation area using full field photic stimulator was about 9.6%. The activation index was greatest on full field, second on half field and smallest on focal central field in 4. The index of half field was greater than that of full field in 1. The ranges of activation index were full field 43-73%(mean 55%), half field 22-40 %(mean 32%), and focal central field 5-24%(mean 13%). Conclusion: The degree of visual cortex activation increases with the size of photic stimulator.

• Journal of the Korean Society of Radiology
• /
• v.14 no.6
• /
• pp.773-780
• /
• 2020

With the development of the 4th industrial, research is being conducted to prevent diseases and reduce damage in various fields of science and technology such as medicine, health, and bio. As a result, artificial intelligence technology has been introduced and researched for image analysis of radiological examinations. In this paper, we will directly apply a deep learning model for classification and detection of pneumonia using chest X-ray images, and evaluate whether the deep learning model of the Inception series is a useful model for detecting pneumonia. As the experimental material, a chest X-ray image data set provided and shared free of charge by Kaggle was used, and out of the total 3,470 chest X-ray image data, it was classified into 1,870 training data sets, 1,100 validation data sets, and 500 test data sets. I did. As a result of the experiment, the result of metric evaluation of the Inception V3 deep learning model was 94.80% for accuracy, 97.24% for precision, 94.00% for recall, and 95.59 for F1 score. In addition, the accuracy of the final epoch for Inception V3 deep learning modeling was 94.91% for learning modeling and 89.68% for verification modeling for pneumonia detection and classification of chest X-ray images. For the evaluation of the loss function value, the learning modeling was 1.127% and the validation modeling was 4.603%. As a result, it was evaluated that the Inception V3 deep learning model is a very excellent deep learning model in extracting and classifying features of chest image data, and its learning state is also very good. As a result of matrix accuracy evaluation for test modeling, the accuracy of 96% for normal chest X-ray image data and 97% for pneumonia chest X-ray image data was proven. The deep learning model of the Inception series is considered to be a useful deep learning model for classification of chest diseases, and it is expected that it can also play an auxiliary role of human resources, so it is considered that it will be a solution to the problem of insufficient medical personnel. In the future, this study is expected to be presented as basic data for similar studies in the case of similar studies on the diagnosis of pneumonia using deep learning.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.25 no.4
• /
• pp.361-374
• /
• 2009

For successful osteogenesis around the implants, interaction between implant surface and surrounding tissue is important. Biomechanical bonding and biochemical bonding are considered to influence the response of adherent cells. But the focus has shifted surface chemistry. The purpose of this study is to evaluate the MC3T3-E1 osteoblast like cell responses of magnesium (Mg) ion implanted titanium surface produced using a plasma source ion implantation method. Commercially pure titanium disc was used as substrates. The discs were prepared to produce four different surface, A: Machine turned surface, B: Mg implanted surface, C: sandblasted surface, D: sandblasted and Mg implanted surface. MC3T3 El osteoblastic like cells were cultured on the disc specimens. Cell adhesion, proliferation, differentiation, and synthesis of extracellular matrix were evaluated. The cell adhesion morphology was evaluated by SEM. RT PCR assay was used for assessment of cell adhesion, proliferation and differentiation. ALP activity was measured for cell differentiation. The results of this study were as follows: 1. SEM showed that cell on Mg ion groups was more proliferative than that of non Mg ion groups. On the machine turned surface, cell showed some degree of contact guidance in aligning with the machining grooves. 2. In RT PCR analysis, osteonectin and c-fos mRNA were more expressed on sandblasted and Mg ion implanted group. 3. ALP activity was not significantly different among all groups. Within the limitations of this study, the following conclusions were drawn: It might indicate Mg ion implanted titanium surface induce better bone response than non Mg ion groups.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.1
• /
• pp.116-126
• /
• 2013

Glycol ethers are a group of solvents based on alkyl ethers of ethylene glycol commonly used in paints. These solvents typically have a higher boiling point, together with the favorable solvent properties of lower-molecular weight ethers and alcohols. The word "Glycol ethers" was registered as a United States trademark by Union Carbide Corp. Typically, glycol ethers are found in pharmaceuticals, sunscreens, cosmetics, inks, dyes and water based paints. On the other hand, glycol ethers are used in degreasers, cleaners, aerosol paints and adhesives. Most glycol ethers are relatively water soluble, biodegradable and only a few are considered toxic. Therefore, they are unlikely to pose an adverse risk to the environment. Recent study suggests that occupational exposure to glycol ethers is related to low motile sperm count in men, but the finding has been disputed by others. In this study, skin permeation of 3 types glycol ethers were studied in vitro using matrix such as solvent and detergent. The absorption of glycol ethers[methyl glycol ethers(MC), ethyl glycol ethers(EC) and butyl glycol ethers(BC)] has been measured in vitro through rat skin. Epidermal membranes were set up in Franz diffusion cells and their permeability to PBS measured to establish the integrity of the skin before the glycol ethers were applied to the epidermal surface. Absorption rates for each glycol ethers were determined and permeability assessment made to quantify any irreversible alterations in barrier function due to contact with the esters. Types of glycol ethers in vitro experimental results on MC> EC> BC quickly appeared in the following order: skin permeation was beneficial to the skin permeation small molecular weight, the difference in chemical structure, such as hydrophilic, because with the partition coefficient and solubility mechanisms and passive diffusion to increase the speed at which transmission is considered.

• Journal of Oral Medicine and Pain
• /
• v.36 no.1
• /
• pp.53-63
• /
• 2011

Osteoarthritis (OA), the most common form of arthritis, is a result of both mechanical and biological events that destabilize the normal coupling of degradation and synthesis of articular cartilage chondrocytes and extracelluar matrix, and subchondral bone. Although it is likely that the molecular basis of pathogenesis is similar to that of other joints, additional study of the temporomandibular joint (TMJ) is required due to its unique structure and function. This study was carried out to evaluate the epidemiologic characteristics of TMJ osteoarthritis. The purpose of this study was to investigate the prevalence of TMJ OA in Patients with temporomandibular disorders (1405 men and 2922 women whose mean age was $30.2\; {\pm}\; 15.4$ and $33.1\;{\pm}\;15.2$ years, respectively) who had visited the TMJ and Orofacial Pain Clinic of Seoul National University Dental Hospital in 2007. Orthopantomograms, TMJ tomograms and transcranial radiographs were used to evaluate degenerative change of the mandibular condyle. The obtained results were as follows: 1. Degenerative change of the mandibular condyle was observed in 883 (20.4%) of 4327 subjects. The prevalence was significantly higher in women (706 patients, 24.1%) than in men (177 patients, 12.6%), and this significant difference between genders was observed in all age groups. 2. The prevalence of degenerative change of the mandibular condyle in TMD patients showed a gentle increase along with age. Such increase was statistically significant in women (P < 0.001), but not in men. 3. Sclerosis was observed the most frequently in all age groups and the mean age of the patients with osteophyte was the highest among four types of degenerative change. 4. Although men showed degenerative change in the left side more often and women showed degenerative change more frequently in both sides, the difference of distribution in sides between genders was not significant. In conclusion, the prevalence of degenerative change of the mandibular condyle in TMD patients is higher in women than in men, and increases steadily with aging, but not as dramatically as in other joints that show a steep increase in prevalence around the age of 45 years. It can be suggested that the epidemiologic characteristic of OA of the TMJ differs from those of other joints, and that a more extensive study based on the general population is necessary.

• Journal of Periodontal and Implant Science
• /
• v.29 no.4
• /
• pp.873-893
• /
• 1999

The ultimate goal of periodontal therapy is the regeneration of periodontal tissue and repair of function. For more than a decade there have been many efforts to develop materials and bioactive molecule(such as growth factor and differentiation factors) to promote periodontal wound healing. Among the bioactive molecules, bone morphogenetic protein(BMP) was studied for periodontal wound healing. Since Urist demonstrated that demineralized bone matrix could induce the formation of cartilage and bone in ectopic site, many studies on BMP have been reported. Among those BMPs, it was reported that rhBMP-2 enhanced the healing of bone defects in animal studies and clinical studies. However, its efficacy in periodontal regeneration, especially 1-wall intrabony defects is still unknown. The purpose of this study was to examine the effect of rhBMP-2/ACS on the epithelial migration, gingival connective tissue adhesion, cementum formation, alveolar bone regeneration in intrabony defects of dogs. Four millimeter deep and four millimeter wide 1-wall defects were surgically created in the mesial aspects of the 3rd incisors. The test group received rhBMP-2/ACS with a flap procedure and the control underwent buffer/ACS with a flap procedure. Histologic analysis after 8 weeks of healing revealed the following results: 1. The length of epithelial growth(the distance from alveolar crest to the apical end of JE) was $0.9{\pm}1.5mm$ in the control group and $1.2{\pm}1.4mm$ in the test group. There was no statistically significant difference between the two groups. 2. The length of connective tissue adhesion was $2.4{\pm}1.3mm$ in the control group and $1.2{\pm}1.1mm$ in the test group. The control group showed significantly enhanced adhesion(P<0.05). 3. The length of new cementum was $0.9{\pm}1.0mm$ in the control group and $1.7{\pm}0.8mm$ in the test group. The test group showed significantly enhanced cementum regeneration(P<0.05). 4. The length of new bone height was $1.9{\pm}0.6mm$ in the control group and $2.4{\pm}0.9mm$ in the test group. There was no statistically significant difference between the two groups. 5. The new bone area was $4.7{\pm}1.7mm^2$ in the control group and $8.0{\pm}2.0mm^2$ in the test group. The test group showed significantly enhanced bone formed area(P<0.05). 6. The new bone density was $73.0{\pm}8.6%$ in the control group and $66.6{\pm}15.3%$ in the test group. There was no statistically significant difference between the two groups. These results suggest that the use of rhBMP-2 in 1-wall intrabony defects has significant effect on new cementum and new bone formation area, but doesn't have any significant effect on the prevention of junctional epithelium migration and new bone formation height.

• Applied Microscopy
• /
• v.38 no.4
• /
• pp.293-306
• /
• 2008

The essential factor of acute respiratory distress syndrome (ARDS), an acute lung injury accompanied commonly by sepsis syndrome is accumulation of neutrophils in lung tissue. The study attempted to confirm whether a lung injury would be decreased with the anti-inflammatory effect of germanium by the treated germanium prior to the development of ARDS and whether nitric oxide influence in suppressing a lung injury. Test groups were divided in the following structure for experiment; CON that has been administered with sodium chloride to airway, LPS administered with endotoxin for 5 hours in the same amount and 5 hours of endotoxin administered Ge+LPS following 1 hours of pre-treated germanium. The result of a test using experimental animals, infilteration of neutrophils (p<0.001) in bronchoalveolar lavage fluid (BALF) was significantly decreased, the structure of lung tissue was preserved relatively well, and much neutrophils with distinct positive were observed on tunel staining which showed increase of apoptotic neutrophils in the pre-treated germanium group compare to the endotoxin administrated group. In observation of ultrastructural changes of cell in BALF, phagocytic alveolar macrophage was increased in alveolar space, the nucleus of most engulfed neutrophils were condensed, and some apoptosis neutrophils appears to be DNA fragmentation and effacement of cellular organelles were found in intercellular matrix in the pre-treated germanium group. However, the nitric oxide showed increase in all the groups excluding CON, and the nitric oxide effect such as degranulation diminishing of mast cells and apoptosis increase of neutrophils in the pre-treated group only. The situation appears that there was change in internal environment of the experimental animal by the pre-treated germanium before the nitric oxide is produced and the anti-inflammatory effect activated the pre-processed germanium by nitric oxide which activated following the change. Therefore, the nitric oxide created from macrophage in accordance with the pre-treated germanium appears to influence in alleviating a lung injury. Accordingly, acute lung injury is alleviated by the anti-inflammatory effect of germanium such as inhibition of neutrophils migration, induction of neutrophil apoptosis and increase of phagocytic function of phagocyte, and the nitric oxide produced from activated macrophage by germanium would influence in suppressing a lung injury.

• The Journal of Korean Academy of Prosthodontics
• /
• v.53 no.4
• /
• pp.325-329
• /
• 2015

Purpose: The aim of this study was to compare the film thicknesses of several resin cements as a function of time after mixing and to examine the effect of working time on the film thicknesses. Materials and methods: The film thickness (${\mu}m$) of 4 resin cements (n=10), 1 composite resin (Panavia F 2.0), 3 self-adhesive resin (Clearfil SA luting, Zirconite, RelyX U200) cements was measured at 20-second intervals after mixing of the cements up to 200 seconds under a load of 50 N. Linear regression was fitted to verify the effect of working time on the film thickness of each cement. Data were compared to the working time recommended by manufacturers using Wilcoxon test ($\alpha$=.05). Results: All of the materials showed a positive linear correlation between the film thickness and working time. There was no statistically significant difference between the working time based on our results and the values recommended by the manufacturers even though there was a discrepancy between those two values. Conclusion: The film thickness of resin cements could increase with the increase of working time. Working time to meet the ISO standard of $50-{\mu}m$ maximum film thickness could be different from the manufacturer's recommended value.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.26 no.4
• /
• pp.652-663
• /
• 1999

Craniosynostosis, the premature fusion of cranial sutures, presumably involves disturbance of the interactions between different tissues within the cranial sutures. Interestingly, point mutaions in the genes encoding for the fibroblast growth factor receptors(FGFRs), especially FGFR2, cause various types of human craniosynostosis syndromes. To elucidate the function of these genes in the early morphogenesis of mouse cranial sutures, we first analyzed by in situ hybridization the expression of FGFR2(BEK) and osteopontin, an early marker of osteogenic differentiation, in the sagittal suture of calvaria during embryonic(E15-E18) and postnatal stage(P1-P3). FGFR2(BEK) was intensely expressed in the osteogenic fronts, whose cells undergo differentiation into osteoprogenitor cells that ultimately lay down the bone matrix. Osteopontin was expressed throughout the parietal bones excluding the osteogenic fronts, the periphery of the parietal bones. To further examine the role of FGF-mediated FGFR signaling in cranial suture, we did in vitro experiments in E15.5 mouse calvarial explants. Interestingly, implantation of FGF2 soaked beads onto both the osteogenic fronts and mid-mesenchyme of sagittal suture after 36 hours organ culture resulted in the increase of the tissue thickness and cell number around FGF2 beads, moreover FGF4-soaked beads implanted onto the osteogenic fronts stimulated suture closure due to an accelerated bone growth, compared to FGF4 beads placed onto mid-mesenchyme of sagittal suture and BSA control beads. In addition FGF2 induced the ectopic expression of osteopontin and Msx1 genes. Taken together, these data indicate that FGF-mediated FGFR signaling has a important role in regulating the cranial bone growth and maintenance of cranial suture, and suggest that FGF-mediated FGFR signaling is involved in regulating the balance between the cell proliferation and differentiation through inducing the expression of osteopontin and Msx1 genes.